Grafana Dashboard using Telegraf with additional plugins

[VictorRobellini]

@wrightsonm My influx sits around 6GB. Every now and then I start reading up on Influx retention and downsampling, but I end up just truncating my db since it's faster.

[SeaMonkey]

@seamonkey said in Grafana Dashboard using Telegraf with additional plugins:

@victorrobellini 7.1.1, but I wouldn't think that would make a difference regarding my particular issue. Your design applies the value mapping function to all fields within the panel, but instead it should only be applied to the Status column exclusively under the Override settings. I've fixed this on my own dashboard and I started to attempt a pull request to fix it, but didn't have the patience to manually adjust only the relevant lines in your JSON file and reimport for testing.

I just updated my dashboard and this is still an issue. Anyone with interfaces that have a MAC address starting with 00 will have 'DOWN' listed as their physical address.

[VictorRobellini]

@seamonkey What does the data in influx show?

Good point about the value mapping and threshold. I've updated the interfaces widget to apply thresholds and value mapping to just the Status column.

[SeaMonkey]

@victorrobellini said in Grafana Dashboard using Telegraf with additional plugins:

What does the data in influx show?

Sounds like you got it fixed, but just in case it's still relevant...

> select * from  interface where mac_address!='Unavailable' limit 2
name: interface
time                friendlyname host             ip4_address ip4_subnet ip6_address ip6_subnet ip_address    mac_address       name source   status
----                ------------ ----             ----------- ---------- ----------- ---------- ----------    -----------       ---- ------   ------
1607846650000000000 LAN          fallia.thegalaxy                                               192.168.0.1   00:15:17:xx:xx:xx em0  pfconfig 1
1607846650000000000 WAN          fallia.thegalaxy                                               00.00.00.00   00:15:17:xx:xx:xx em1  pfconfig 1

[VictorRobellini]

@seamonkey The data looks good. I've already committed the update that isolates the value/thresholds to status.

Is your IP really null?

[SeaMonkey]

@victorrobellini The mac addresses are there, I've just censored the last three hex pairs for the sake of privacy. Same for the WAN IP. There's nothing wrong with the influx data, and as I mentioned previously, I was able to fix the problem by moving the value mappings under the Field tab to the Overrides tab in order to explicitly apply them to the Status field - which it sounds like you've implemented in the latest update.

[wrightsonm]

@victorrobellini I've done a bit of investigation into the Series Cardinality of the database.

We changed the ip_block_log grok pattern to tag more fields. As a result the cardinality of the database increased significantly. The downside to this is querying the database to show the new pfBlocker detail section became very RAM intensive. I was using > 20GB RAM in influxdb to display the last 10mins on the grafana dashboard. I had an OOM Out of Memory issue that crashed my Docker VM, so at this point I dropped the entire measurement and influx memory memory usage looked much happier again.

After 2 days of collecting new pfblocker data, I looked at the Cardinality of the database using this query (I am using Influx 2.0.4):

import "influxdata/influxdb/v1"
cardinalityByTag = (bucket) =>
v1.tagKeys(bucket: bucket)
|> map(fn: (r) => ({
tag: r._value,
_value: if contains(set: ["_stop","_start"], value:r._value) then
0
else
(v1.tagValues(bucket: bucket, tag: r._value)
|> count()
|> findRecord(fn: (key) => true, idx: 0))._value
}))
|> group(columns:["tag"])
|> sum()
|> keep(columns: ["tag","_value"])
cardinalityByTag(bucket: "pfsense")

(Whilst Influx 2 does have a cardinality function, it is only currently available in the Cloud variant, not the OSS variant....
The above function does the job though)

Cardinality was 34540! Influx is currently using 6GB RAM at this level.
Breaking this down it is attributed to:

• src_port: 15780
• dest_port:10603
• src_ip:7980
• other metrics (not many)

I have now changed my telegraf config to tag less stuff. For now i've untagged src_ip, dest_ip, src_port, dest_port

grok_patterns = ["^%{SYSLOGTIMESTAMP:timestamp:ts-syslog},%{NUMBER:rulenum},%{DATA:interface},%{WORD:friendlyname},%{WORD:action},%{NUMBER:ip_version},%{NUMBER:protocolid},%{DATA:protocol:tag},%{IPORHOST:src_ip},%{IPORHOST:dest_ip},%{WORD:src_port},%{NUMBER:dest_port},%{WORD:direction},%{WORD:geoip_code:tag},%{DATA:ip_alias_name},%{DATA:ip_evaluated},%{DATA:feed_name:tag},%{HOSTNAME:resolvedhostname},%{GREEDYDATA:clienthostname},%{GREEDYDATA:ASN},%{GREEDYDATA:duplicateeventstatus}"]

The next step is to look into rewriting the dashboard to perform the required grouping and aggregation.

I've started with this table:
IP - Top 10 Blocked - IN (By Host/Port)

Original query:

SELECT TOP("blocked",10),src_ip,dest_ip, protocol FROM
(
SELECT count("action") as "blocked" FROM "autogen"."tail_ip_block_log" WHERE ("host" =~ /^$Host$/ AND "action" = 'block' AND "direction" = 'in' ) AND $timeFilter GROUP BY src_ip,dest_ip,protocol
)

New V2 Query using Flux:

from(bucket: "pfsense")
  |> range(start: v.timeRangeStart, stop: v.timeRangeStop)
  |> filter(fn: (r) => r["_measurement"] == "tail_ip_block_log")
  |> filter(fn: (r) => r["_field"] == "src_ip" or r["_field"] == "dest_ip" or r["_field"] == "dest_port" or r["_field"] == "action" or r["_field"] == "direction" or r["_field"] == "protocolid" or r["_field"] == "host")
  |> pivot(rowKey:["_time"], columnKey: ["_field"], valueColumn: "_value")
  |> filter(fn: (r) => r.host =~ /^.*$/ and r.action == "block" and r.direction == "in" and r.protocolid =~ /^(6$|17$)/)
  |> group(columns:["src_ip","dest_ip","dest_port"])
  |> rename(columns:{action: "Blocked"})
  |> count(column: "Blocked")
  
  |> group()  //use group to ungroup data and return to a single table
  |> top(n:10, columns: ["Blocked"])  
  |> sort(columns: ["Blocked"], desc: true)
  |> yield()

This is as far as I have got for the time being.
Thought I would share this before I got too far into updating the dashboard.
I suspect I won't get a good view of performance imrpovement until I've redone all of the pfBlocker Details section.
Also raising this now as it involves an update from Influx v1 to v2 to support the flux language.
Once you get used to flux, it is really quite powerful.
The old influxql language can still be used with v2, they are backwards compatible.

You thoughts & opinions are appreciated.

[bigjohns97]

Is anyone else noticing some broken pfblocker panels with the latest pfblocker update?

Looks like the $timefilter seems to make the panel show no data for some reason, I tried messing with it with no success outside of removing the time filter all together which isn't really a usable solution.

[wrightsonm]

@bigjohns97 is this pfsense v2.6?
I think some logging was broken and there is a patch that you can apply. Can't remember where I read it, it might be an issue on the GitHub issues for the grafana dashboard.

I haven't upgraded yet and am waiting for the next official release.

[wrightsonm]

@wrightsonm
https://github.com/VictorRobellini/pfSense-Dashboard/issues/58

[bigjohns97]

@wrightsonm said in Grafana Dashboard using Telegraf with additional plugins:

@bigjohns97 is this pfsense v2.6?
I think some logging was broken and there is a patch that you can apply. Can't remember where I read it, it might be an issue on the GitHub issues for the grafana dashboard.

I haven't upgraded yet and am waiting for the next official release.

I remember applying this patch when 2.6 came out so I didn't think it was the same but it turns out the newest update to pfblocker requires the same patch to be re-implemented.

At least until 3.1.0_3 is released it seems.

[bigjohns97]

Anyone else have their pfblockerng panels break recently (guessing with the new version of grafana?)

[wrightsonm]

@bigjohns97 working for me on grafana v9.2.1

[bigjohns97]

@wrightsonm Don't upgrade, this was working for me not too long ago.

[bigjohns97]

Noticed this was working again this morning, version is now 9.4.7, so I am guessing this was a bug.

[thimplicity]

I have probably missed it in the thread. Is there a way to get this up and running with InfluxDB 2.x?

[bigjohns97]

@thimplicity You should see this being mentioned above
https://forum.netgate.com/post/992280