Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    How to setup IPv6 on PFsense behind ER-X (ISP modem)

    IPv6
    3
    30
    3.3k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • A
      appollonius333 @JKnott
      last edited by

      @jknott I will keep that in mind, thank you for the tip :) As I am not that experienced with IPv6. So looking at my main post what would be the first thing to do for me to get my setup to work?

      JKnottJ 1 Reply Last reply Reply Quote 0
      • JKnottJ
        JKnott @appollonius333
        last edited by

        @appollonius333

        Yep. BTW, I have been using IPv6 on my network for almost 11 years.

        One piece of advice I often give is to keep things simple. Get it working first. Since you apparently have multiple LANs, get one going first, then add the others, repeating what you did with the first, but using a unique prefix ID.

        Just last week, I built a new pfsense firewall, as the computer I had previously run it on died. My first goal was to get it working with just the WAN & LAN. Then I imported my previous config and made sure my VLAN and test LAN worked. And this morning, I redid my OpenVPN config. When you do things in a step by step manner, instead of Trying to do everything at once, you can see what might be causing the problems.

        Also, get in the habit of downloading config backups. It just takes a few seconds, but make it easy to back out of a bad config.

        PfSense running on Qotom mini PC
        i5 CPU, 4 GB memory, 32 GB SSD & 4 Intel Gb Ethernet ports.
        UniFi AC-Lite access point

        I haven't lost my mind. It's around here...somewhere...

        A 1 Reply Last reply Reply Quote 0
        • A
          appollonius333 @JKnott
          last edited by

          @jknott What do you mean by Unique Prefix ID? The /subnet notation or this part: ab997d24-9f15-43be-9d6e-5c96cc884394-image.png

          JKnottJ 1 Reply Last reply Reply Quote 0
          • JKnottJ
            JKnott @appollonius333
            last edited by

            @appollonius333

            In the "IPv6 Prefix ID" box, you put a unique ID for each interface. Typically, you'd use 0 for the main LAN, but you could choose whatever you want within the range of 0 - ffff. I have a /56 and use 0 for main, 3 for my guest WiFi VLAN, 4 for my test LAN and ff for my OpenVPN tunnel. As I mentioned, the subnet should always be /64 for LANs.

            PfSense running on Qotom mini PC
            i5 CPU, 4 GB memory, 32 GB SSD & 4 Intel Gb Ethernet ports.
            UniFi AC-Lite access point

            I haven't lost my mind. It's around here...somewhere...

            A 1 Reply Last reply Reply Quote 0
            • A
              appollonius333 @JKnott
              last edited by

              @jknott Ahh, but when I do that I get this error and I don't know why, couldnt find anything about it which I could understand...

              The specified IPv6 Prefix ID is out of range. (wan) - (0) - (0)

              JKnottJ 1 Reply Last reply Reply Quote 0
              • JKnottJ
                JKnott @appollonius333
                last edited by

                @appollonius333

                Are you getting a /48? And what values are you selecting?

                PfSense running on Qotom mini PC
                i5 CPU, 4 GB memory, 32 GB SSD & 4 Intel Gb Ethernet ports.
                UniFi AC-Lite access point

                I haven't lost my mind. It's around here...somewhere...

                A 1 Reply Last reply Reply Quote 0
                • A
                  appollonius333 @JKnott
                  last edited by

                  @jknott Yeah I am getting a /48 on the ER-X, which delegates a /64 to my HomeLAN, where my PFsense is connected to.

                  I have selected these values on the WAN interface and DHCP6 configuration:
                  b5c79dd8-1d4e-4c9a-b763-c56844c21994-image.png

                  JKnottJ 1 Reply Last reply Reply Quote 0
                  • JKnottJ
                    JKnott @appollonius333
                    last edited by

                    @appollonius333

                    Any reason you're using DHCPv6? Generally, SLAAC is used. Also, Android devices won't work with DHCPv6, as for some unfathomable reason it's not supported.

                    PfSense running on Qotom mini PC
                    i5 CPU, 4 GB memory, 32 GB SSD & 4 Intel Gb Ethernet ports.
                    UniFi AC-Lite access point

                    I haven't lost my mind. It's around here...somewhere...

                    A 1 Reply Last reply Reply Quote 0
                    • A
                      appollonius333 @JKnott
                      last edited by

                      @jknott Yeah when I do that I don't see any IPv6 addresses assigned to my WAN interface. It just has a Link Local address now

                      JKnottJ 2 Replies Last reply Reply Quote 0
                      • JKnottJ
                        JKnott @appollonius333
                        last edited by JKnott

                        @appollonius333

                        Actually, that's entirely normal. Link local addresses are often used for routing. If there is a public WAN address, it's likely not used for routing. Did you have one before?

                        PfSense running on Qotom mini PC
                        i5 CPU, 4 GB memory, 32 GB SSD & 4 Intel Gb Ethernet ports.
                        UniFi AC-Lite access point

                        I haven't lost my mind. It's around here...somewhere...

                        A 1 Reply Last reply Reply Quote 0
                        • A
                          appollonius333 @JKnott
                          last edited by

                          @jknott yeah when I configured the WAN interface as DHCP6. But this means that I should see a Ipv6 Address on the LAN interface?

                          JKnottJ 1 Reply Last reply Reply Quote 0
                          • JKnottJ
                            JKnott @appollonius333
                            last edited by

                            @appollonius333

                            No, one has nothing to do with the other. I have DHCPv6-PD on the WAN side and SLAAC on the LAN side. The nice thing about SLAAC is it works without any configuration needed. The router advertises the 64 bit LAN prefix and the client provides the lower 64 bits, based on either the MAC address or a random number.

                            PfSense running on Qotom mini PC
                            i5 CPU, 4 GB memory, 32 GB SSD & 4 Intel Gb Ethernet ports.
                            UniFi AC-Lite access point

                            I haven't lost my mind. It's around here...somewhere...

                            1 Reply Last reply Reply Quote 1
                            • JKnottJ
                              JKnott @appollonius333
                              last edited by

                              @appollonius333 said in How to setup IPv6 on PFsense behind ER-X (ISP modem):

                              eah when I do that I don't see any IPv6 addresses assigned to my WAN interface. It just has a Link Local address now

                              Here's my configuration. You should have 48, instead of 56 for the prefix size.

                              8c3b22bb-c757-4506-827b-9f5690ca9958-image.png

                              PfSense running on Qotom mini PC
                              i5 CPU, 4 GB memory, 32 GB SSD & 4 Intel Gb Ethernet ports.
                              UniFi AC-Lite access point

                              I haven't lost my mind. It's around here...somewhere...

                              A 1 Reply Last reply Reply Quote 0
                              • A
                                appollonius333 @JKnott
                                last edited by appollonius333

                                @jknott Would the /48 still apply when the PFsense machine gets a /64 address from the /64 LAN subnet on the ER-X? Also where do you use the DHCP6 Client Configuration on? The LAN interface?

                                A 1 Reply Last reply Reply Quote 0
                                • A
                                  appollonius333 @appollonius333
                                  last edited by appollonius333

                                  @JKnott

                                  This is how my Network looks:
                                  cf50af06-ab7e-4005-9b37-687a5fd81f3f-image.png

                                  JKnottJ 1 Reply Last reply Reply Quote 0
                                  • JKnottJ
                                    JKnott @appollonius333
                                    last edited by

                                    @appollonius333

                                    Is that ER-X in bridge or gateway mode? You want bridge mode for pfsense to provide multiple /64s. Otherwise, you're only getting a single /64 from your ISP, not a /48.

                                    PfSense running on Qotom mini PC
                                    i5 CPU, 4 GB memory, 32 GB SSD & 4 Intel Gb Ethernet ports.
                                    UniFi AC-Lite access point

                                    I haven't lost my mind. It's around here...somewhere...

                                    A 1 Reply Last reply Reply Quote 0
                                    • A
                                      appollonius333 @JKnott
                                      last edited by

                                      @jknott the Er-X is a gateway, so it receives and has all the settings for TV, phones etc. KPN in the Netherlands is giving us a /48 subnet on residential connections

                                      JKnottJ 1 Reply Last reply Reply Quote 0
                                      • JKnottJ
                                        JKnott @appollonius333
                                        last edited by

                                        @appollonius333

                                        If you're in gateway mode, you do not have a /48. I have a similar setup, with Rogers in Canada. I have a box that provides Internet, IPTV and phone. I put it into bridge mode, as in gateway mode it would provide only a single /64. In bridge mode I get a /56. Also, in bridge mode you'll get a public IPv4 address, unless your ISP uses carrier grade NAT.

                                        Bridge vs gateway mode should have no effect on the other services. In my case, the home phone plugs into the modem. The IPTV works on the same network as my LAN.

                                        PfSense running on Qotom mini PC
                                        i5 CPU, 4 GB memory, 32 GB SSD & 4 Intel Gb Ethernet ports.
                                        UniFi AC-Lite access point

                                        I haven't lost my mind. It's around here...somewhere...

                                        A 1 Reply Last reply Reply Quote 0
                                        • A
                                          appollonius333 @JKnott
                                          last edited by appollonius333

                                          @jknott Yeah the ISP gives us a /48. But from that /48 a /64 is assigned to my LAN environment.
                                          I don't think it is in either mode to be honest.
                                          The bridge mode I know, but gateway mode well we don't use that here in NL I think.

                                          JKnottJ 1 Reply Last reply Reply Quote 0
                                          • JKnottJ
                                            JKnott @appollonius333
                                            last edited by

                                            @appollonius333

                                            I noticed your IPv4 address, which is within the RFC1918 range and indicates NAT is used. You don't want that. Put it in bridge mode or you will not be able to use most of the /48. There's no two ways about it.

                                            PfSense running on Qotom mini PC
                                            i5 CPU, 4 GB memory, 32 GB SSD & 4 Intel Gb Ethernet ports.
                                            UniFi AC-Lite access point

                                            I haven't lost my mind. It's around here...somewhere...

                                            A 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.