Interfaces not showing in Dataplane KVM

Ralms 0 · Mar 17, 2021, 3:15 PM

@derelict I didn't even do anything special, was just a standard installation from the ISO :(

Ralms 0 · Mar 17, 2021, 3:38 PM

@derelict
So, doing nmclid device status I can confirm that those 2 interfaces are not being managed:

Now how to make them literally not show, I haven't figured it out.

Derelict · Mar 17, 2021, 6:30 PM

@ralms-0 I get this:

[root@tnsr-a1 etc]# nmcli device status
Error: NetworkManager is not running.

Wonder what the difference between your KVM install and mine is.

I have not yet installed 21.03-2 from ISO here and have only upgraded existing installations. Let me see if I can do that soon and if there is any difference.

Derelict · Mar 17, 2021, 7:18 PM

@ralms-0 No idea what the difference is. After reinstalling fresh with three vtnet adapters and configuring the third one in the installer as a host interface, Networkmanager is still not running and the first two interfaces are available to the dataplane with no action by me.

Ralms 0 · Mar 17, 2021, 7:43 PM

@derelict hm ok, I can reinstall again.
There must be something different.
What did you configure regarding networking during the wizard?

Derelict · Mar 17, 2021, 8:07 PM

@ralms-0 I just enabled the third interface and enabled DHCP on it. Set it to apply after boot and to the installer wizard. When I quit that it showed it had received a DHCP address on ens20.

Ralms 0 · Mar 17, 2021, 9:12 PM

@derelict hm ok, that was the same thing I've done, with the difference that I've set also DNS on the ens20, but that shouldn't be any different.

I will reinstall it and report back all the steps I've took :)

Ralms 0 · Mar 17, 2021, 9:40 PM

@derelict To split my replies, here is the installation wizard phase:

VM:

The network devices were added to the VM with Firewall off:

VM starting point:

Installation Wizard base:

Wizard starting point:

Changed timezone to Lisbon:

Setting storage:

Installation Wizard Network:

Starting point:

Set hostname to tnsr:

Configure ens20:

Set IPv4 to dhcp and IPv6 to ignore:

Tick option 7 and 8 for Connect automatically after reboot and Apply Configuration in installer

Go back to wizard home and not touch the other 2 interfaces:

Installation Wizard finish:

Confirm the Software Selection:

Processing:

All set:

Being installation:

Ralms 0 · Mar 17, 2021, 10:06 PM

@derelict

Installation Complete:

Automatic Reboot.
First Login:

Interfaces and Network Manager:

So it shows as "Not running", so I might have enabled it by accident when I set the NM_CONTROLLED.

show interface returns nothing.

Set Interfaces Down as mention in the docs:

Default config from ENS18:

Set NM_CONTROLLED to no:

Without Reboot, still nothing:

Rebooted the system.

Interfaces still now showing up.

Set network name:

So yeah, I have no idea what is going on, what I'm doing wrong.

This is a Proxmox 6.3-6 running on an HP DL360p Gen8.

lastactionhero · Mar 19, 2021, 10:57 PM

@ralms-0
@Derelict

I am also struggling with this. This is my first time attempting to install, registered earlier this week. I am not using Proxmox, but KVM libvirt natively. I installed latest version from ISO, serial setup, with 8 virtio network bridge interfaces. I am not looking to pass anything through or use SR-IOV, as eventually I'd like this to migrate between my hosts. Upon completed installation, only my configured host interface is active. I tried both static and/or dhcp, this always works.

tnsr# show version

Version: tnsr-v21.03-2
Build timestamp: Thu Mar  4 10:29:54 2021 CST

I dropped to host shell, NetworkManager service is not running.

systemctl start NetworkManager
systemctl enable NetworkManager

This get's NetworkManager going again. I am not sure why it wasn't running and enabled. I am then able to issue "nmcli device status" to get results of all my interfaces. I then apply "NM_CONTROLLED=no" to respective ifcfg-enp1s0, etc interfaces so they are unmanaged. Reboot for good measure.

And thats where I'm at... It's still not working after reboot.

tnsr(config)# dataplane dpdk dev 
  0000:01:00.0          Ethernet controller: Red Hat, Inc. Virtio network device (rev 01)                                                                                                                                                      
  0000:02:00.0          Ethernet controller: Red Hat, Inc. Virtio network device (rev 01)                                                                                                                                                      
  0000:03:00.0          Ethernet controller: Red Hat, Inc. Virtio network device (rev 01)                                                                                                                                                      
  0000:04:00.0          Ethernet controller: Red Hat, Inc. Virtio network device (rev 01)                                                                                                                                                      
  0000:05:00.0          Ethernet controller: Red Hat, Inc. Virtio network device (rev 01)                                                                                                                                                      
  0000:06:00.0          Ethernet controller: Red Hat, Inc. Virtio network device (rev 01)                                                                                                                                                      
  0000:07:00.0          Ethernet controller: Red Hat, Inc. Virtio network device (rev 01)                                                                                                                                                      
  0000:08:00.0          Ethernet controller: Red Hat, Inc. Virtio network device (rev 01)                                                                                                                                                      
  default

Trying to configure name's for interfaces.

tnsr(config)# dataplane dpdk dev 0000:01:00.0 network name WAN1
Changes to dataplane startup settings require a dataplane restart to take effect.
tnsr(config)# dataplane dpdk dev 0000:02:00.0 network name WAN2
Changes to dataplane startup settings require a dataplane restart to take effect.
tnsr(config)# service dataplane restart

Show interface results in nothing.

I've read through release notes known issues and I am not sure if this is not a supported configuration or not and known. My KVM hosts, running Ubuntu 20.10, netplan interfaces are configured as bridges with VLAN's, on bonded 10Gbit interfaces.

lastactionhero · Mar 20, 2021, 2:20 AM

Some more troubleshooting

[root@esg01 admin]# sudo dmesg | grep virtio_net
[    4.078543] virtio_net virtio1 enp2s0: renamed from eth1
[    4.084586] virtio_net virtio2 enp3s0: renamed from eth2
[    4.091946] virtio_net virtio3 enp4s0: renamed from eth3
[    4.101909] virtio_net virtio4 enp5s0: renamed from eth4
[    4.136131] virtio_net virtio0 enp1s0: renamed from eth0
[    4.146091] virtio_net virtio5 enp6s0: renamed from eth5
[    4.171685] virtio_net virtio7 enp8s0: renamed from eth7
[    4.203872] virtio_net virtio6 enp7s0: renamed from eth6

[root@esg01 admin]# sudo tnsrctl status
vpp.service: activating
clixon-backend.service: activating
clixon-restconf.service: activating
tnsr-boot.service: active
tnsr-dataplane-netns.service: active
frr-dataplane.service: inactive
strongswan-dataplane.service: inactive
nginx-dataplane.service: inactive
ntpd-dataplane.service: inactive
unbound-dataplane.service: inactive
sshd-dataplane.service: inactive
snmp-subagent-dataplane.service: inactive
snmpd-dataplane.service: inactive
nginx.service: inactive
ntpd.service: inactive
snmp-subagent.service: inactive
snmpd.service: inactive
DHCPv4 server: inactive

[root@esg01 admin]# sudo systemctl status vpp
● vpp.service - Vector Packet Processing Process
   Loaded: loaded (/usr/lib/systemd/system/vpp.service; enabled; vendor preset: enabled)
  Drop-In: /usr/lib/systemd/system/vpp.service.d
           └─intentional-restart.conf, nm-wait-online.conf, on-failure.conf, requires-dataplane.conf
   Active: activating (auto-restart) (Result: exit-code) since Fri 2021-03-19 16:24:36 PDT; 4s ago
  Process: 2591 ExecStopPost=/bin/cp /etc/tnsr/tnsr-running.xml /etc/tnsr.xml (code=exited, status=0/SUCCESS)
  Process: 2590 ExecStopPost=/bin/echo TNSR startup mode switch : using running DB (code=exited, status=0/SUCCESS)
  Process: 2588 ExecStopPost=/bin/echo VPP stopped, modifying TNSR startup mode (code=exited, status=0/SUCCESS)
  Process: 2586 ExecStart=/usr/bin/vpp -c /etc/vpp/startup.conf (code=exited, status=1/FAILURE)
  Process: 2584 ExecStartPre=/sbin/modprobe uio_pci_generic (code=exited, status=0/SUCCESS)
  Process: 2582 ExecStartPre=/bin/rm -f /dev/shm/db /dev/shm/global_vm /dev/shm/vpe-api (code=exited, status=0/SUCCESS)
 Main PID: 2586 (code=exited, status=1/FAILURE)
    Tasks: 0 (limit: 49476)
   Memory: 0B
   CGroup: /system.slice/vpp.service
[root@esg01 admin]# sudo systemctl status clixon-backend         
● clixon-backend.service - Clixon backend
   Loaded: loaded (/usr/lib/systemd/system/clixon-backend.service; enabled; vendor preset: enabled)
   Active: activating (start-post) since Fri 2021-03-19 16:24:21 PDT; 46s ago
  Process: 2404 ExecStartPost=/usr/bin/echo TNSR startup mode switch : using none (code=exited, status=0/SUCCESS)
  Process: 2403 ExecStartPost=/usr/bin/cp -f /etc/tnsr/tnsr-none.xml /etc/tnsr.xml (code=exited, status=0/SUCCESS)
  Process: 2402 ExecStartPost=/usr/bin/echo clixon_backend started successfully, modifying TNSR startup mode (code=exited, status=0/SUCCESS)
  Process: 2341 ExecStart=/usr/sbin/clixon_backend (code=exited, status=0/SUCCESS)
    Tasks: 1 (limit: 49476)
   Memory: 23.8M
   CGroup: /system.slice/clixon-backend.service
           └─2401 /usr/sbin/clixon_backend

Mar 19 16:24:21 esg01 clixon_backend[2341]: os_priv_change: changing uid from 0 to 0
Mar 19 16:24:21 esg01 clixon_backend[2341]: Mar 19 16:24:21: os_priv_change: changing uid from 0 to 0
Mar 19 16:24:21 esg01 clixon_backend[2341]: Startup successful, no backup needed
Mar 19 16:24:21 esg01 clixon_backend[2341]: Mar 19 16:24:21: Startup successful, no backup needed
Mar 19 16:24:21 esg01 clixon_backend[2401]: clixon_backend: 2401 Started
Mar 19 16:24:21 esg01 systemd[1]: clixon-backend.service: Can't convert PID files /var/tnsr/tnsr.pidfile O_PATH file descriptor to proper file descriptor: Permission denied
Mar 19 16:24:21 esg01 echo[2402]: clixon_backend started successfully, modifying TNSR startup mode
Mar 19 16:24:21 esg01 echo[2404]: TNSR startup mode switch : using none
Mar 19 16:24:21 esg01 systemd[1]: clixon-backend.service: Can't convert PID files /var/tnsr/tnsr.pidfile O_PATH file descriptor to proper file descriptor: Permission denied
Mar 19 16:24:21 esg01 systemd[1]: clixon-backend.service: Can't convert PID files /var/tnsr/tnsr.pidfile O_PATH file descriptor to proper file descriptor: Permission denied
[root@esg01 admin]# sudo systemctl status clixon-restconf
● clixon-restconf.service - Clixon restconf
   Loaded: loaded (/usr/lib/systemd/system/clixon-restconf.service; enabled; vendor preset: enabled)
   Active: activating (auto-restart) (Result: exit-code) since Fri 2021-03-19 16:25:19 PDT; 2s ago
  Process: 2711 ExecStart=/www-data/clixon_restconf (code=exited, status=203/EXEC)
 Main PID: 2711 (code=exited, status=203/EXEC)

Derelict · Mar 20, 2021, 2:20 AM

@lastactionhero Does the host see the interfaces when running something like

sudo ip link

in the host namespace?

If so, then you must get the host to relinquish the interfaces before you can add them to the dataplane.

I do not know off-hand the particular recipe for doing so in your case. All I know is I have zero problems installing tnsr in proxmox-wrapped KVM virtual machines using virtio NICs. If I ever do find myself in that predicament I just add ONBOOT and NM_CONTROLLED set to no and reboot.

tnsr-b1 tnsr# host shell ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
4: ens20: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000
    link/ether 2a:d4:de:20:c8:db brd ff:ff:ff:ff:ff:ff

tnsr-b1 tnsr(config)# dataplane dpdk dev 
  0000:00:12.0          Ethernet controller: Red Hat, Inc. Virtio network device                                                    
  0000:00:13.0          Ethernet controller: Red Hat, Inc. Virtio network device                                                    
  0000:00:14.0          Ethernet controller: Red Hat, Inc. Virtio network device                                                    
  0000:00:15.0          Ethernet controller: Red Hat, Inc. Virtio network device                                                    
  default              

tnsr-b1 tnsr# show config run json
snip

      "dpdk": {
        "dev": [
          {
            "id": "0000:00:12.0",
            "name": "outside"
          },
          {
            "id": "0000:00:13.0",
            "name": "inside"
          },
          {
            "id": "0000:00:15.0",
            "name": "opt1"
          }
        ]
      },
                                                                                
tnsr-b1 tnsr# show interface ip
Interface: inside
    IPv4 MTU: 0 bytes
    IPv4 Route Table: ipv4-VRF:0
    IPv4 addresses:
        172.29.101.1/29

Interface: loop0
    IPv4 MTU: 0 bytes
    IPv4 Route Table: ipv4-VRF:0

Interface: opt1
    IPv4 MTU: 0 bytes
    IPv4 Route Table: ipv4-VRF:0
    IPv4 addresses:
        172.29.105.1/24

Interface: outside
    IPv4 MTU: 0 bytes
    IPv4 Route Table: ipv4-VRF:0
    IPv4 addresses:
        172.25.228.57/24

I wish I could be more help right now but that's really all I have.

lastactionhero · Mar 20, 2021, 5:31 AM

Some more troubleshooting. This looks to be permissions related issue.

@Derelict When you install, are you enabling root account with a password? Or are you creating a user account, making it a member of administrator (root)? I'm doing the later, making an admin user account, member of administrators (root). The root account remains disabled.

I was able to get this working, but only for troubleshooting more of the issue, not resolving it. I think I would need support at this point to chime in, fix a bug here, which I'm not going to pay for at this time. I really want this to just work because I've heard good things regarding performance and I really want this. I'd like to switch from my current VyOS which just works.

My steps above with NetworkManager work to sort out the interfaces making them unmanaged. As the journalctl -xe logs indicated, vpp.service is the issue, it's not starting. I can manually start this if I drop to host shell and execute vpp with the config.

[admin@esg01 ~]$ sudo /usr/bin/vpp -c /etc/vpp/startup.conf
[sudo] password for admin: 
/usr/bin/vpp[7433]: perfmon: skipping source 'intel-uncore' - intel_uncore_init: no uncore units found
/usr/bin/vpp[7433]: tls_init_ca_chain:609: Could not initialize TLS CA certificates
/usr/bin/vpp[7433]: tls_mbedtls_init:644: failed to initialize TLS CA chain
/usr/bin/vpp[7433]: tls_init_ca_chain:710: Could not initialize TLS CA certificates
/usr/bin/vpp[7433]: tls_openssl_init:784: failed to initialize TLS CA chain

Once this is running, I am then able to see my interfaces in tnsr CLI, dataplane dpdk dev. Everything jives up at this point as you mention in your replies as it should. No more errors in the CLI either.

esg01 tnsr# show interface 
Interface: Guest
    Admin status: down
    Link down, link-speed 10 Gbps, unknown duplex
    Link MTU: 1500 bytes
    MAC address: 52:54:00:7b:f7:69
    IPv4 MTU: 0 bytes
    IPv4 Route Table: ipv4-VRF:0
    IPv6 MTU: 0 bytes
    IPv6 Route Table: ipv6-VRF:0
    VLAN tag rewrite: disable
    Rx-queues
        queue-id 0 : cpu-id 1
    counters:
      received: 0 bytes, 0 packets, 0 errors
      transmitted: 0 bytes, 0 packets, 0 errors
      protocols: 0 IPv4, 0 IPv6
      0 drops, 0 punts, 0 rx miss, 0 rx no buffer

Interface: Management
    Admin status: down
    Link down, link-speed 10 Gbps, unknown duplex
    Link MTU: 1500 bytes
    MAC address: 52:54:00:d4:64:23
    IPv4 MTU: 0 bytes
    IPv4 Route Table: ipv4-VRF:0
    IPv6 MTU: 0 bytes
    IPv6 Route Table: ipv6-VRF:0
    VLAN tag rewrite: disable
    Rx-queues
        queue-id 0 : cpu-id 1
    counters:
      received: 0 bytes, 0 packets, 0 errors
      transmitted: 0 bytes, 0 packets, 1 errors
      protocols: 0 IPv4, 0 IPv6
      0 drops, 0 punts, 0 rx miss, 0 rx no buffer

Interface: WAN1
    Admin status: down
    Link down, link-speed 10 Gbps, unknown duplex
    Link MTU: 1500 bytes
    MAC address: 52:54:00:a5:5c:04
    IPv4 MTU: 0 bytes
    IPv4 Route Table: ipv4-VRF:0
    IPv6 MTU: 0 bytes
    IPv6 Route Table: ipv6-VRF:0
    VLAN tag rewrite: disable
    Rx-queues
        queue-id 0 : cpu-id 1
    counters:
      received: 0 bytes, 0 packets, 0 errors
      transmitted: 0 bytes, 0 packets, 0 errors
      protocols: 0 IPv4, 0 IPv6
      0 drops, 0 punts, 0 rx miss, 0 rx no buffer

Interface: WAN2
    Admin status: down
    Link down, link-speed 10 Gbps, unknown duplex
    Link MTU: 1500 bytes
    MAC address: 52:54:00:f1:5a:97
    IPv4 MTU: 0 bytes
    IPv4 Route Table: ipv4-VRF:0
    IPv6 MTU: 0 bytes
    IPv6 Route Table: ipv6-VRF:0
    VLAN tag rewrite: disable
    Rx-queues
        queue-id 0 : cpu-id 1
    counters:
      received: 0 bytes, 0 packets, 0 errors
      transmitted: 0 bytes, 0 packets, 0 errors
      protocols: 0 IPv4, 0 IPv6
      0 drops, 0 punts, 0 rx miss, 0 rx no buffer

Interface: WiFi
    Admin status: down
    Link down, link-speed 10 Gbps, unknown duplex
    Link MTU: 1500 bytes
    MAC address: 52:54:00:22:9e:9b
    IPv4 MTU: 0 bytes
    IPv4 Route Table: ipv4-VRF:0
    IPv6 MTU: 0 bytes
    IPv6 Route Table: ipv6-VRF:0
    VLAN tag rewrite: disable
    Rx-queues
        queue-id 0 : cpu-id 1
    counters:
      received: 0 bytes, 0 packets, 0 errors
      transmitted: 0 bytes, 0 packets, 0 errors
      protocols: 0 IPv4, 0 IPv6
      0 drops, 0 punts, 0 rx miss, 0 rx no buffer

Interface: Workstation
    Admin status: down
    Link down, link-speed 10 Gbps, unknown duplex
    Link MTU: 1500 bytes
    MAC address: 52:54:00:45:31:92
    IPv4 MTU: 0 bytes
    IPv4 Route Table: ipv4-VRF:0
    IPv6 MTU: 0 bytes
    IPv6 Route Table: ipv6-VRF:0
    VLAN tag rewrite: disable
    Rx-queues
        queue-id 0 : cpu-id 1
    counters:
      received: 0 bytes, 0 packets, 0 errors
      transmitted: 0 bytes, 0 packets, 0 errors
      protocols: 0 IPv4, 0 IPv6
      0 drops, 0 punts, 0 rx miss, 0 rx no buffer

esg01 tnsr#

I will reinstall again tomorrow trying with root account enabled. I don't know what else to do beyond this.

Derelict · Mar 20, 2021, 8:31 PM

@lastactionhero I usually make an additional admin-level account but I never enable root. I generally log in using the tnsr user.

lastactionhero · Mar 21, 2021, 1:44 AM

Installing using virt-manager works. I have no issues performing a install and interfaces are present for use right away. No errors.

Installing via my kvm host, using virt-install seems to be where the issue is. Reviewing the domain XML's for any difference, I cannot find any difference. Very strange. If I find what's missing I'll update the post, but it works fine as a VM and virtio installing using virt-manager.

Ralms 0 · Mar 23, 2021, 9:15 PM

So, destiny decided that I should have received a support ticket with Netgate about this. (I was very surprised about it)

The support experience was very impressive and the engineer identified the issue really fast.

Proxmox uses QEMU, which integrates KVM.
It happens that the default CPU Type, "kvm64", doesn't have all the instruction extensions required, such as SSE 4.2, as mentioned here:
https://docs.netgate.com/tnsr/en/latest/platforms/kvm/#creating-a-vm

I've changed the VM to use CPU Type "Nehalem" and it worked out of the box, with the steps I've shared before.

Hope it helps others in the future :)

Thanks.

lastactionhero · Mar 23, 2021, 10:14 PM

I too was able to resolve my issue. I apologize for hijacking this thread thinking it was similar underlying issue.

The difference between working and not working was when using virt-install, I need to use --cdrom for specifying the install ISO. Using --location ends up not working. While the installation completes, network interfaces do not. Virt-manager worked because it was using cdrom and not location.

Works:

sudo virt-install --cdrom tnsr.iso

Does not work:

sudo virt-install --location tnsr.iso