How to setup a Host Override

johnpoz · Nov 13, 2021, 2:20 PM

@jimfreeze again yes home.arpa is default... And right there in your dhcp server it clearly states that system will be used

And again if unbound has no entry for the system name.. Did you change that or get rid of it?

From your previous post

So again - if unbound has no entry for pfsense.home.arpa or whatever other domain you might set in system. Then NO it could not respond for a query.. How would it know what to respond with, etc..

jimfreeze · Nov 13, 2021, 2:37 PM

@johnpoz I don't think you understand the problem. The problem is not that I believe the router should break the laws of physics or that it should function in a way it's not supposed to. The problem is there are multiple touchpoints in configuring a system to work, and they do not work out of the box. That is, they do not define the home.arpa domain and clients are not able to resolve home.arpa when that domain is defined in "General Setup".

So far we have talked about 3 configuration points to get a local domain defined and resolvable:

"General Setup": Hostname and Domain
"DHCP Server": Gateway and 'Domain name' left blank to use default host
"DNS Resolver": No config added

The above steps do not allow clients to resolve home.arpa.
I am not seeing in the docs how this setup should be done. It seems like it should be a basic procedure.

johnpoz · Nov 13, 2021, 2:54 PM

@jimfreeze said in How to setup a Host Override:

and they do not work out of the box.

Sorry but they do.. I have setup pfsense countless times.. All of it just works out of the box..

are not able to resolve home.arpa when that domain is defined in "General Setup".

What would they resolve home.arpa too? That is just the domain, there is no host there.. So no trying to resolve just home.arpa wouldn't resolve to anything... What should resolve is pfsense.home.arpa since that would be the default fqdn..

Out of the box pfsense

Working just fine...

Here is that other file I said to look at - on a default fire up of pfsense..

So I am not sure what you have going on - but this works just out of the box..

jimfreeze · Nov 13, 2021, 3:00 PM

@johnpoz So, that is the real question. Why is that line not getting defined on my router?

arm64:~ % nslookup pfsense.home.arpa
Server:		192.168.100.1
Address:	192.168.100.1#53

** server can't find pfsense.home.arpa: SERVFAIL

arm64:~ % ping pfsense.home.arpa
ping: cannot resolve pfsense.home.arpa: Unknown host

It's almost certain that I have some config that is preventing that from happening, but I don't know what it could be. You have verified the settings are correct on General setup, DNS resolver and DHCP server.

/etc/hosts is still the same and does not include the pfSense line like yours does.

[21.05.2-RELEASE][admin@pfSense.home.arpa]/root: cat /etc/hosts
127.0.0.1	localhost localhost.home.arpa
::1	localhost localhost.home.arpa
[21.05.2-RELEASE][admin@pfSense.home.arpa]/root:

Can you think of a configuration setting that I changed that would cause this?

MoonKnight · Nov 13, 2021, 3:05 PM

@jimfreeze

What DNS servers do you have in your General Setup?

jimfreeze · Nov 13, 2021, 3:07 PM

@ciscox None

MoonKnight · Nov 13, 2021, 3:17 PM

@jimfreeze
Are you behind your own router/modem from your ISP?
Does pfSense get WAN IP (public IP) or private IP from the modem/router?
If it gets a private IP, it means that your modem/router is acting as a router with DHCP. Are you sure you don't have any kind of IP conflicts?

Could you please take a screenshot of your DNS Resolver/General Settings?

johnpoz · Nov 13, 2021, 3:24 PM

none of what his wan IP is public or not, etc.. has anything to do with resolving just the local name of pfsense. Pfsense wan could be unplugged, and would still be able to resolve its own name.

What is ODD.. Is what he shows in general setup is not actually listed in unbound configuration files. Which if not there then no he would not be able to resolve it..

Why that is or what could cause that I have no idea to be honest..

Simple solution might be to just redo pfsense, or do a factory reset.. But all of this is just out of the box works. I don't even know what could of been done to F it up..

jimfreeze · Nov 13, 2021, 3:27 PM

Are you behind your own router/modem from your ISP?

It is an ATT modem, which I have set as a pass through.
The pfSense gets an address via DHCPS-dynamic.
All packet filter and firewall settings are off.

Does pfSense get WAN IP (public IP) or private IP from the modem/router?

 ifconfig ix3
ix3: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: WAN
	options=e138bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6>
	ether 90:ec:77:1d:1a:a0
	inet6 fe80::92ec:77ff:fe1d:1aa0%ix3 prefixlen 64 scopeid 0x8
	inet6 2600:1702:4c72:c400::22 prefixlen 128
	inet6 2600:1702:4c72:c400:92ec:77ff:fe1d:1aa0 prefixlen 64 autoconf
	inet 107.131.42.156 netmask 0xfffffe00 broadcast 107.131.43.255
	media: Ethernet autoselect (1000baseT <full-duplex,rxpause,txpause>)
	status: active
	nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>

If it gets a private IP, it means that your modem/router is acting as a router with DHCP. Are you sure you don't have any kind of IP conflicts?

No IP conflicts that I can tell.

Could you please take a screenshot of your DNS Resolver/General Settings?

MoonKnight · Nov 13, 2021, 3:30 PM

@johnpoz
You're right, but I liked to start with the simple settings, that's probably has nothing to do with the problem, but nice to make sure the settings are okay :)

I believe there is something with his unbound settings or just a bad config.
Maybe like you say, doing a clean install would probably solve it?

MoonKnight · Nov 13, 2021, 5:31 PM

@jimfreeze

That's strange. I just did a clean install of pfsense 2.5.2 on new VM.
It did work out of the box.

johnpoz · Nov 13, 2021, 6:23 PM

@ciscox said in How to setup a Host Override:

That's strange.

Not strange ;) Over the years I have done hundreds of pfsense installs. Always works out of the box every single time.. Follow the bouncing ball - bam working system out of the box 100% of the time..

I do not recall ever having an issue with a clean install.. Over the years when playing with snapshot versions I have had some issues on some snapshots, etc.

Really having a hard time coming up with why/how it could even be messed up to where the settings in system are not in the unbound config..

jimfreeze · Nov 13, 2021, 7:54 PM

@johnpoz I rebuilt from factory defaults and it had the proper pfsense.home.arpa in /etc/hosts and /var/unbound/host....

However, after making some changes (my guess is in LAN or creating a bridge) it went back to not including pfsense.home.arpa.

So, I triggered the issue a second time.

Now I'm seeing if I can pinpoint how that is happening.

johnpoz · Nov 13, 2021, 8:53 PM

@jimfreeze said in How to setup a Host Override:

creating a bridge

Why are you creating a bridge?

jimfreeze · Nov 13, 2021, 10:18 PM

@johnpoz To bridge some LAN ports.

johnpoz · Nov 13, 2021, 10:25 PM

@jimfreeze if you need more ports, use a switch.. You could pick up a 8 port gig smart switch for like $40..

https://www.amazon.com/NETGEAR-8-Port-Gigabit-Ethernet-Managed/dp/B07PLFCQVK/ref=psdc_281414_t3_B08P2C2GXF

Dumb switch for like $20

What exactly are you doing?
https://docs.netgate.com/pfsense/en/latest/bridges/interfaces.html