Traffic is not re-routed over secondary internet connection (PPPOE), once it returns from being down.

w0w

@bnetworker
I have plain PPPoE, no modem, just ethernet cable. I'll try some other methods tomorrow, I hope, and let you know.

w0w

@bnetworker
No, I can not re-produce this on the 22.05.b.20220524.1701, what build you have now?

BNetworker

@w0w

22.05.b.20220524.0600, but I've had this issue on every recent version. So, it may be a difference in config that is causing the issue. My setup is

DSL -> Modem in Bridge Mode (Carrier VLAN setup here) -> PFSense (Auth here)

w0w

@bnetworker
How did you configure the default gateway? Mine is configured as group and using tiers to prioritize which one is the primary.

BNetworker

@w0w -

Yes the overall default gateway is my primary gateway group, WAN1WAN2, with WAN 1 having tier 1 priority, WAN2 Tier 2.

But... configured in the firewall for INSIDE, I have explicitly setup the WAN1WAN2 gateway group as being their default gateway. The Guest network explicitly has WAN2WAN1.

Now that the filters are reloading at the end of the rc.newwanip, I've had zero failover issues. It's been working great.

w0w

@bnetworker
I've similar configuration and anyway I've tried — I don't have this re-routing issue on the last build without any patching.

BNetworker

@w0w - It would be interesting to see if when your PPPoE returns, if you see "Filter Reload" in your logs. Mine does not, until I put in the manual workaround.

w0w

@bnetworker
Looks like yes... but not sure...
When it's going down

Jun 4 07:11:46 	php-fpm 	61963 	/rc.openvpn: MONITOR: WAN_PPPOE has packet loss, omitting from routing group WAN_FAIL_BACK
Jun 4 07:11:46 	check_reload_status 	47693 	Reloading filter

When it's UP


Jun 4 07:17:25 	check_reload_status 	47693 	Reloading filter
Jun 4 07:17:25 	check_reload_status 	47693 	Restarting OpenVPN tunnels/interfaces
Jun 4 07:17:25 	check_reload_status 	47693 	Restarting IPsec tunnels
Jun 4 07:17:25 	check_reload_status 	47693 	updating dyndns HENETV6_TUNNELV6
Jun 4 07:17:25 	rc.gateway_alarm 	16761 	>>> Gateway alarm: HENETV6_TUNNELV6 (Addr:x001:xx0:27:191::1 Alarm:1 RTT:0.000ms RTTsd:0.000ms Loss:100%)
Jun 4 07:17:23 	php-fpm 	93505 	/rc.newwanip: Removing static route for monitor 8.8.8.8 and adding a new route through x0.0.x00.1
Jun 4 07:17:22 	php-fpm 	93505 	/rc.newwanip: Default gateway setting Interface HENETV6_TUNNELV6 Gateway as default.
Jun 4 07:17:22 	php-fpm 	93505 	---xxx.xxx.xxx.xxx---|---xxx.xxx.xxx.xxx---|WAN_PPPOE|0.254ms|0.022ms|0.0%|online|none
Jun 4 07:17:22 	php-fpm 	93505 	/rc.newwanip: MONITOR: WAN_PPPOE is available now, adding to routing group WAN_FAIL_BACK
Jun 4 07:17:22 	kernel 		gif0: link state changed to UP
Jun 4 07:17:22 	kernel 		gif0: link state changed to DOWN 
*********
Jun 4 07:17:20 	ppp 	17338 	[wan] IFACE: Up event
Jun 4 07:17:20 	check_reload_status 	47693 	rc.newwanip starting pppoe0 
*********

This "Reloading filter" appears several times, not just PPPoE, but also Ipv6 tunneling and IPSEC, Openvpn (Resyncing OpenVPN instances for interface WAN) and so on, and I have other "spam" in logs too, like snort. So sometimes it's very difficult to understand what was exactly happened.

BNetworker

Hey @jimp - Just wanted to give an update on this. Been working perfectly with the modifications as below. I just have to remember to insert the filter_configure after every update:

}
} else {
	/* signal filter reload */
	filter_configure();
}

filter_configure();
?>

If there is any way I can help narrow down the issue as to why this is needed, please let me know.

Thanks!

jimp

Leave a note on https://redmine.pfsense.org/issues/13228 that the fix works for you.

It's still something I plan on changing for the next release it just hasn't happened yet.