GW configuration - some questions

viragomann · Feb 22, 2023, 5:34 PM

@empbilly
Did you run the capture on VLAN interface set the protocol filter to ARP?
So it shouldn't show any public IP. You can hide the MACs if you want.

empbilly · Feb 22, 2023, 6:14 PM

@viragomann

I capture all packets.
https://www.dell.com/support/kbdoc/pt-br/000184095/dell-emc-networking-os6-series-switches-how-to

I scp the .pcap file from the switch to my computer and opened it in wireshark.

I couldn't find an option where I could specify the vlan for packet capture.

Can it be with all traffic?

viragomann · Feb 22, 2023, 6:38 PM

@empbilly said in GW configuration - some questions:

I couldn't find an option where I could specify the vlan for packet capture.

This should be possible in the capture configuration. Isn't there any interface setting?

Can it be with all traffic?

Yes.

Run the capture on the port which your PC is connected. Start it and try to ping a CARP VIP.
If the IP isn't in the PCs ARP table there should be an ARP request and a response in the capture. But presumably it doesn't get a response.

Then run a capture on the port which is connected to pfSense to see if the request is passed through.

empbilly · Feb 22, 2023, 7:42 PM

I have configured VIP CARP of vlan IOT as GW in dhcp. The file below is from a direct capture from pfsense.
packetcapture.cap

@viragomann said in GW configuration - some questions:

Then run a capture on the port which is connected to pfSense to see if the request is passed through.

Tomorrow I will do that part.

viragomann · Feb 22, 2023, 9:20 PM

@empbilly said in GW configuration - some questions:

I have configured VIP CARP of vlan IOT as GW in dhcp.

And which IP are we lookinf for?

empbilly · Feb 22, 2023, 11:10 PM

@viragomann

vlan IOT: 10.10.56.0/27
VIP CARP/GW: 10.10.56.1
DHCP server/interface: 10.10.56.2 (pfmaster)

Test from IP: 10.10.56.13

viragomann · Feb 22, 2023, 11:19 PM

@empbilly
So you can see the ARP requests for the VIP and responses with the CARP MAC.
If these responses reach the device at 10.10.56.13, it should add the MAC to its ARP table.

But obviously there is something going wrong. Even though there are ARP requests and correct responses for the CARP, the VIP is never addressed.

empbilly · Feb 23, 2023, 1:34 PM

@viragomann said in GW configuration - some questions:

Even though there are ARP requests and correct responses for the CARP, the VIP is never addressed.

That is not good!!! :(

Yesterday I tried disabling the IGMP protocol on the switch, but anyway, I still can't get internet access when I configure VIP CARP as GW in DHCP.

I made new packet captures and they seem to say the same thing as the one above that I shared.

I would have to disable IGMP on all the switches in our infrastructure, correct?

EDIT1:
Anyway I disabled IGMP Snooping on the switches connected from our NOC to our office, but it still didn't go. Either they don't support the CARP traffic or there is some configuration to be done.

viragomann · Feb 23, 2023, 1:34 PM

@empbilly
To you see the ARP responses from 10.10.56.1 also on 10.10.56.13?
And if so, do you see the entry in its ARP table?

If the ARP responses from the VIP reache the device, the issue can't be caused by the switch.

Is it the same result if you try to access a CARP VIP from another device?

empbilly · Feb 23, 2023, 2:34 PM

@viragomann said in GW configuration - some questions:

To you see the ARP responses from 10.10.56.1 also on 10.10.56.13?
And if so, do you see the entry in its ARP table?

10.10.56.13, now .11 is my celphone

packetcapture.cap (new capture)

@viragomann said in GW configuration - some questions:

Is it the same result if you try to access a CARP VIP from another device?

From the machine I use for work, I can ping all the CARP VIPs.

In pfsense packet capture I have selected the vlan (ADM_LAN) corresponding to the IP of my work machine.

The result is below:
23 2.599865 10.60.0.7 10.10.56.1 ICMP 98 Echo (ping) request id=0x002a, seq=1/256, ttl=64 (reply in 24)
24 2.599953 10.10.56.1 10.60.0.7 ICMP 98 Echo (ping) reply id=0x002a, seq=1/256, ttl=64 (request in 23)
31 3.614359 10.60.0.7 10.10.56.1 ICMP 98 Echo (ping) request id=0x002a, seq=2/512, ttl=64 (reply in 32)
32 3.614376 10.10.56.1 10.60.0.7 ICMP 98 Echo (ping) reply id=0x002a, seq=2/512, ttl=64 (request in 31)
35 4.638379 10.60.0.7 10.10.56.1 ICMP 98 Echo (ping) request id=0x002a, seq=3/768, ttl=64 (reply in 36)
36 4.638397 10.10.56.1 10.60.0.7 ICMP 98 Echo (ping) reply id=0x002a, seq=3/768, ttl=64 (request in 35)

If I configure it to capture packets from the IOT vlan and ping from my work machine to GW 10.10.56.1, nothing is captured.

But, I tried pinging another IP (10.10.56.7 - Solar Converter), it didn't ping, but the captured packets appeared.

62 13.745105 10.60.0.7 10.10.56.7 ICMP 98 Echo (ping) request id=0x002e, seq=1/256, ttl=63 (no response found!)
64 14.767583 10.60.0.7 10.10.56.7 ICMP 98 Echo (ping) request id=0x002e, seq=2/512, ttl=63 (no response found!)
67 15.791683 10.60.0.7 10.10.56.7 ICMP 98 Echo (ping) request id=0x002e, seq=3/768, ttl=63 (no response found!)
72 16.815664 10.60.0.7 10.10.56.7 ICMP 98 Echo (ping) request id=0x002e, seq=4/1024, ttl=63 (no response found!)
77 17.839493 10.60.0.7 10.10.56.7 ICMP 98 Echo (ping) request id=0x002e, seq=5/1280,

Other information. I removed VIP CARP 10.10.56.1 from Virtual VIP, tried to ping from my machine and it did not ping. I reconfigured and it pinged.

empbilly · Feb 23, 2023, 6:46 PM

EDIT:

Other information. I removed VIP CARP 10.10.56.1 from Virtual VIP, tried to ping from my machine and it did not ping. I reconfigured and it pinged.
show arp on n1524 shows:

#show arp 

Static ARP entries are only active
when the IP address is reachable on a local subnet


Age Time (seconds)............................. 1200
Response Time (seconds)........................ 1
Retries........................................ 4
Cache Size..................................... 893
Dynamic Renew Mode ............................ Enable
Total Entry Count Current / Peak .............. 14 / 18
Static Entry Count Configured / Active / Max .. 0 / 0 / 16

IP Address       MAC Address        Interface       Type      Age
---------------  -----------------  --------------  --------  -----------
172.16.0.2       8444.6478.FE49     Vl1             Gateway    0h  0m  1s
172.16.4.49      20FD.F146.7102     Vl1             Dynamic    0h  2m 59s
172.16.4.56      D07E.28D5.9073     Vl1             Dynamic    0h 18m 13s
172.16.4.217     E4F0.04D8.8F21     Vl1             Local         n/a
172.16.7.129     D07E.28D7.1A9D     Vl1             Dynamic    0h 18m 41s
172.16.15.16     D07E.28E4.CD3D     Vl1             Dynamic    0h  0m 14s
172.18.0.1       20FD.F150.1389     Vl900           Dynamic    0h  8m 28s
172.18.0.5       2401.C7B1.35C1     Vl900           Dynamic    0h 17m 22s
172.18.0.14      04DA.D206.F1C1     Vl900           Dynamic    0h 17m 11s
172.18.0.17      2401.C7B1.3541     Vl900           Dynamic    0h  3m 16s
172.18.0.21      04DA.D206.F4C1     Vl900           Dynamic    0h 13m 18s
172.18.0.29      E4F0.04D8.8F21     Vl900           Local         n/a
172.18.0.252     8444.6478.FE49     Vl900           Dynamic    0h  0m 12s
172.18.0.254     0000.5E00.0118     Vl900           Gateway    0h  0m 40s
250.251.252.254  0202.BC80.0002     Management      Dynamic   n/a

The vlan 900 is the management vlan for the switches and is the native vlan on the uplink port. The only GW VIP CARP that shows on the arp is from this vlan.

172.18.0.254     0000.5E00.0118     Vl900           Gateway

viragomann · Feb 23, 2023, 6:59 PM

@empbilly said in GW configuration - some questions:

The vlan 900 is the management vlan for the switches and is the native vlan on the uplink port. The only GW VIP CARP that shows on the arp is from this vlan.

I don't expect to see other CARP VIP in the switch ARP table.
If the switch provides layer 2 for the devices it must not communicate with the VIPs of other subnets, but only its management subnet.
The connected devices need to access them, however, since they use them as gateways.

empbilly · Feb 23, 2023, 7:17 PM

@viragomann

@viragomann said in GW configuration - some questions:

I don't expect to see other CARP VIP in the switch ARP table.

ok.

Do I need to disable the IGMP protocol only on the switch that pfsense is directly connected to or do I need to disable it on the other switches in our infrastructure as well?

viragomann · Feb 23, 2023, 7:58 PM

@empbilly
I would not expect that it even interferes with ARP in any way.
Maybe the switch would forward the CARP (VRRP) packets if IGMP is on, since they are multicasts, but CARP works obviously properly. But if it has an impact, disable it on the switch which is connected to pfSense should be sufficient.

empbilly · Feb 24, 2023, 11:26 AM

@viragomann

I am going over our entire topic and my settings and documenting them so that I don't get lost in what has been done.

The question below was answered by another user at the beginning of the topic.

Even if I haven't put pfbackup on the network yet, the GW CARP VIP should work?