Allowed IP Address does not work in captive portal

[susobaco]

@net-mas said in Allowed IP Address does not work in captive portal:

why can I then enter IP networks in the mask?:

I have tried both /32 and /24 and /16 masks and it does not work either way.

[net-mas]

@susobaco
here - my picture:
login-to-view

the functionality is contained directly in the upper right corner of the GUI. So more precisely, the developer cannot point out that he supports IP networks

[susobaco]

As far as I could observe, the script (I guess php) to configure the "Allowed IP Address" page does not correctly save the configuration in the corresponding "rule" file. This would explain, in my case, that no output is obtained when executing "pfSsh.php playback pfanchordrill" in the "pzoneid_2_allowedhosts" section.

[net-mas]

@susobaco said in Allowed IP Address does not work in captive portal:

As far as I could observe, the script (I guess php) to configure the "Allowed IP Address" page does not correctly save the configuration in the corresponding "rule" file. This would explain, in my case, that no output is obtained when executing "pfSsh.php playback pfanchordrill" in the "pzoneid_2_allowedhosts" section.

Unfortunately, none of that means anything to me, I'm not that deep into the PFSense system. I would only be interested here if you can manipulate it: Can you find a variant of how it is stored correctly and thus used correctly with the subnet specification? In other words, is it just a GUI error or a firmware error because of the exchanged ipfw?

[susobaco]

@net-mas said in Allowed IP Address does not work in captive portal:

@susobaco said in Allowed IP Address does not work in captive portal:

As far as I could observe, the script (I guess php) to configure the "Allowed IP Address" page does not correctly save the configuration in the corresponding "rule" file. This would explain, in my case, that no output is obtained when executing "pfSsh.php playback pfanchordrill" in the "pzoneid_2_allowedhosts" section.

Unfortunately, none of that means anything to me, I'm not that deep into the PFSense system. I would only be interested here if you can manipulate it: Can you find a variant of how it is stored correctly and thus used correctly with the subnet specification? In other words, is it just a GUI error or a firmware error because of the exchanged ipfw?

I don't know the system that well either, I am researching, if I find something, I will write it here.

[Gertjan]

@net-mas said in Allowed IP Address does not work in captive portal:

here - my picture:

Hummm.

login-to-view

I never actually saw that one.

If I select /30 as shown, I obtain :

cpzoneid_2_allowedhosts/192.168.2.100**_30** rules/nat contents:
ether pass in quick proto 0x0800 l3 from any to 192.168.2.100**/30** tag cpzoneid_2_auth dnpipe 2012
ether pass in quick proto 0x0800 l3 from 192.168.2.100**/30** to any tag cpzoneid_2_auth dnpipe 2013

That 'looks' correct.
I guess : you subject is wrong ?

It's not "Allowed IP Address does not work in captive portal"
but "Allowed IP Network does not work in captive portal" as an IPv4is a /32, and smaller then /32 is a network.

I'm even not sure. Something like this :

Address: 192.168.2.100 11000000.10101000.00000010.011001 00
Netmask: 255.255.255.252 = 30 11111111.11111111.11111111.111111 00
Wildcard: 0.0.0.3 00000000.00000000.00000000.000000 11
=>
Network: 192.168.2.100/30 11000000.10101000.00000010.011001 00 (Class C)
Broadcast: 192.168.2.103 11000000.10101000.00000010.011001 11
HostMin: 192.168.2.101 11000000.10101000.00000010.011001 01
HostMax: 192.168.2.102 11000000.10101000.00000010.011001 10

[net-mas]

@Gertjan That's correct - it wasn't my topic either, it was originally from someone else. I just stuck around here because I think it was/is similar. If that's wrong, we'll just have to open a new topic.

https://forum.netgate.com/topic/180480/ip-or-mac-passthrough-didn-t-work

here was the original post - but I didn't open it myself. In it, susobaco wrote to me that he probably has a similar problem - hence the cross reference

[susobaco]

link text

[wtasin]

Hi,
I had the same problem.

Look at my post
maybe it helps.

[susobaco]

It seems to be solved by putting the configuration page in English. If you do it that way it worked for me, it seems to be an error with the translation of the "Bold" "From" and "To" options. If you enter them in English, the rules seem to work.
link text