Updating version via console/shell?
-
Mental note, search wiki first before posting….thanks :)
-
np ;D
-
Damn, still no webGUI for me…..(updated to version 0.94.18)
So I can use the 'fetch -o' command to copy a backup config to the pfSense in the same way I guess....cool.
-
Damn, still no webGUI for me…..(updated to version 0.94.18)
So I can use the 'fetch -o' command to copy a backup config to the pfSense in the same way I guess....cool.
Try resetting the lan ip to switch the web server back to HTTP if its in HTTPS.
We switched to LightyHTTPD. There is a reason I haven't released these new versions…
-
that did it, thank you.
-
-
I just tried re-enabling it and I'm locked out again. I'm going to try 0.94.20 that was just posted in the /~sullrich directory.
-
I just tried re-enabling it and I'm locked out again. I'm going to try 0.94.20 that was just posted in the /~sullrich directory.
It's not done uploading!
-
hmmm, I wonder what I just downloaded then…..
-
hmmm, I wonder what I just downloaded then…..
An incomplete version. It's now uploaded.
I really should know, its my home directory.
-
I wasn't trying to be sarcastic, I sincerly wondered what I had downloaded. I didn't know the link for a file showed up in the directory as soon as you start uploading. I'm a windows guy who is used to windows caching everything…anyway.
Ok, 0.94.20 updated, http works, https doesn't.
-
I wasn't trying to be sarcastic, I sincerly wondered what I had downloaded. I didn't know the link for a file showed up in the directory as soon as you start uploading. I'm a windows guy who is used to windows caching everything…anyway.
Ok, 0.94.20 updated, http works, https doesn't.
Ok, thanks. Will look into the https issues.
-
HTTPS is fixed as of 0.95
-
Thank you, it works.
As a side note, as of 0.94.18, the 'Configuring OPT interfaces' no longer takes 3-5 minutes, it's just a few seconds and continues to load. Thanks for that too.
-
Thank you, it works.
As a side note, as of 0.94.18, the 'Configuring OPT interfaces' no longer takes 3-5 minutes, it's just a few seconds and continues to load. Thanks for that too.
Good deal. Please excercise the GUI as much as possible. Try to "crash" it.
-
Well, here is my list i guess
- On the 'Diagnostics: Show States' page, i have to scroll all the way to the bottom of the page to see the states table.
- unchecking the 'Disable NAT Reflection' box still messes up all http traffic going out.
- the ntop service turns itself off for some reason
I suppose only the first is the a webGUI issue, and cosmetic at that.
And a question, you decide if it's webGUI related. On the logs settings page, when I click 'Disable writing log files to the local disk', it doesn't hold the entries in RAM at all? It basically disables logging unless you have a syslog server setup?
-
Well, here is my list i guess
- On the 'Diagnostics: Show States' page, i have to scroll all the way to the bottom of the page to see the states table.
- unchecking the 'Disable NAT Reflection' box still messes up all http traffic going out.
- the ntop service turns itself off for some reason
I suppose only the first is the a webGUI issue, and cosmetic at that.
And a question, you decide if it's webGUI related. On the logs settings page, when I click 'Disable writing log files to the local disk', it doesn't hold the entries in RAM at all? It basically disables logging unless you have a syslog server setup?
1. please take a screen shot
2. you have some nat rule stepping on reflection, need to identify it, i cannot reporduce this
3. look in system logs for ntop entries
4. yes, it will not write entries at all -
http://www.nelsonpapel.com/temp/pfsense.gif
-
-
3. look in system logs for ntop entries
Looks like it gets killed due to lack of RAM (128MB), I didn't create a swap partition due to the CF card. I didn't think ntop was such a memory hog, I usually have under 40% memory usage with it off.
I gotta stop asking questions I can find answers to….
Sorry, but thanks.