SG2100 - Unable to get DHCP WAN IP on GPON interface
-
Hi,
I have a SG2100 and have connected a GPON ONU module into it's SFP with the aim of replacing the ISP router.
The GPON ONU states that the current state is 5 when I execute the command
onu ploamsgThis must imply that the ISP recognises my GPON ONU. However, PFSense does not receive a WAN IP.
Here are the settings, my ISP use IPoE.
- Therefore Interface > WAN Settings have set the "IPv4 Configuration Type" to DHCP
- Configured MAC address spoofing to ISP router
- I've been told to set the VLAN tag as 12.
- Interfaces > VLANs created a new VLAN tag 12 for the WAN interface
- Interfaces > Interface Assignments changed WAN network port to VLAN 12
- Interfaces > Switch > VLANs > Enabled 802.1q VLAN mode > Save
- Interfaces > Switch > VLANs > Add Tag > gave VLAN 12 and members as "1" > Save
Despite following these steps, the WAN interface does not get an WAN IP address. Can you please help?
-
On the 2100 only the LAN uses the onboard switch. The WAN (mvneta0) is a seperate NIC. So you don't need to add any config to the switch settings there, only set the WAN as mvneta0.12.
You may need to assign mvneta0 directly as well because traffic to the GPON module management would not normally be using a VLAN.
I'm not sure what that ONU command is supposed to return. Do you have a link to a manual or command reference?
-
@stephenw10 hi again, thank you for your reply.
The ONU stick is running OpenWrt 14.97_ltq -- Lantiq Edition for GPON
I've been looking at the following:
https://hack-gpon.org/ont-fs-com-gpon-onu-stick-with-mac/
https://resource.fs.com/mall/doc/20230831180515egrzs6.pdf
https://medium.com/@cyayon/configure-onu-gpon-onu-34-20bi-for-orange-isp-2af4fccfc95a
https://github.com/xvzf/zyxel-gpon-sfp
Can you please clarify what do you mean by -
"You may need to assign mvneta0 directly as well because traffic to the GPON module management would not normally be using a VLAN." -
@stealthmode I’m using that exact combo (2100 + FS GPON ONU) so we know pfSense and the SFP module plays nice together.
Since you are seeing state 5 in onu ploamsg you are connected to the ISP’s GPON tree, and we are likely then dealing with missing or wrong pfSense config. This can be VERY tricky to troubleshoot however, as the ISP holds the keys to the kingdom.
What country and ISP are you trying to connect to? I’m using my setup in France and using Orange as the ISP.
Orange’s use of IPoE is VERY VERY strict, and requires a LOT of specific DHCP options to be configured + VLAN priority settings - otherwise they simply do no not reply to to your pfSenses DHCP REQUESTs - and nothing works.So you need to find some way to verify what VLAN and DHCP settings is required by your ISP to accept DHCP requests.
-
@stealthmode said in SG2100 - Unable to get DHCP WAN IP on GPON interface:
Can you please clarify what do you mean by -
"You may need to assign mvneta0 directly as well because traffic to the GPON module management would not normally be using a VLAN."If you are certain your ISP is using VLAN 12 for their services, you do not need to assign mvneta0 to an interface unless you wish to be able to SSH to the GPON module (for status and management). Your WAN should be assigned to mvneta0.12
You could then assign mvneta0 to a OPT1 interface and give it a static 192.168.1.1/24 address. That would allow you to SSH to pfSense, and from there SSH to 192.168.1.10 (The GPON ONU) -
@keyser Thank you very much for confirming!
I'm in Portugal and my ISP is MEO.
Let me dig through what the possible DHCP options might be.
I wanted to confirm another thing - that since I see status 5 on ONU, that means that there are no settings which need to be modified on the ONU? is that right? Basically, the ISP recognises the ONU.
-
@stealthmode said in SG2100 - Unable to get DHCP WAN IP on GPON interface:
I wanted to confirm another thing - that since I see status 5 on ONU, that means that there are no settings which need to be modified on the ONU? is that right? Basically, the ISP recognises the ONU.
As far as I know and understand how the GPON ONU/ONT topology works yes - The ONU is connected and logged into the GPON tree, so traffic should be able to flow. The trouble is that when the ISP is using IPoE authentication (The DHCP exchange is the authentication), no traffic will flow your way before you have authenticated. So you are likely unable to verify if traffic is flowing by doing a promiscious packet capture on your OPT1 (mvneta0) interface. But try and do it anyways - it will show any frames your pfsense sends, and if you were authenticated it would show any frames (including vlan 12 tagged ones - your WAN) inbound to your pfsense - normally broadcasts/Arp and such. Perhaps you could be lucky that they allow certain frames to pass even in unauthenticated state - thus verifying that traffic is actually flowing.
The only thing i’m a little unsure of is MAC addressing. On my ISP (Orange) it is necessecary to clone the ISPs router box MAC address to the GPON ONU - otherwise it won’t log into the GPON tree. After that connection is established (state 5) and the ONU enters bridgemode, Orange doesn’t really care about the router (pfSense) MAC address on the WAN interface. I decided to clone the router MAC address to pfSense as well. But your ISP may or may not care about the MAC address - both on the ONU side and the Router/pfSense side.
-
Do you not even see a response to DHCP requests without the correct incantation?
-
@stephenw10 Nope, if your DHCP frame is not formattted correctly with the required DHCP options to authenticate, then there will be no DHCP reply/offer. So you are unable to verify if traffic actually works or your VLAN tagging is correct.
On top of that my ISP - Orange - requires all DHCP frames to be priority 6 tagged as well. If they are not, no replies are made.
-
Urgh, well that's not easy then!
#funtimes -
@stephenw10 Indeed - if the ISP is strict like Orange, it will be impossible to to make it work unless you have one of two options:
- Someone inside info from the ISP to be able configure all the right settings.
- Be able to do a packet capture of your original ISP routers DHCP exchange and mimic all settings in pfSense
In Orange’s case there is a large internet forum in france where thousands of people share their findings + a representative (unofficial I presume) from Orange shares the strict requirements their end verifies before passing authentication.
-
@keyser said in SG2100 - Unable to get DHCP WAN IP on GPON interface:
Be able to do a packet capture of your original ISP routers DHCP exchange and mimic all settings in pfSense
How should I be able to do this? any ideas?
-
@stealthmode not really No since your ISP is using GPON. It would require special hardware that can bridge the GPON fiber and give you a capture sitting in the middle.
If your ISP router has another WAN port (RJ45), it might work by linking that to your pfsense while doing a packet capture on the pfsense port. The ISP router might send the same crafted DHCP request on the RJ45 WAN port as it does on the GPON fiber port when linking up/booting.
Alternatively you would need an ISP router that is hacked to mirror packets to a secondary port (if possible at all on that HW).
All you need is a copy of that first DHCP request frame as that shows all options and if needed prioriry settings.
-
Mmm, but finding someone else who has already done it for your ISP would be easiest. Perhaps there is some local forum for users?
-
@stealthmode I’m from Denmark, but my french “connection” required me to find all the info I needed on this french site: https://lafibre.info/index.php
There is a LOT of info sharing on various ISPs on that site. Perhaps someone there have also been working with MEO if they are present in France, or if that someone has remote sites in Portugal.
-
@stealthmode I can see there is some discussions about ISP’s in portugal. Perhaps you can find something here:
https://lafibre.info/europe-sud/ -
@keyser said in SG2100 - Unable to get DHCP WAN IP on GPON interface:
https://lafibre.info/europe-sud/
Thank you very much! I'm enquiring on this forum as well as other forums for this ISP
-
Great news! I logged into the CLI of the router and was able to capture some additional details on the WAN interface.
Interface: erouter0 MAC Address : <removed> Description: Interface_erouter0 Type: IPoE Vlan 802.1p: 0 Vlan Mux ID: 12 Vlan TPID: 0x8100 IPv6: Enabled IGMP Proxy: Enabled IGMP Source: Enabled MLD Proxy: Disabled MLD Source: Disabled NAT: Enabled NAT Type: Masquerade Firewall IPv4: Enabled Firewall IPv6: Enabled Force Disable Firewall IPv4: Disabled Force Disable Firewall IPv6: Disabled ARPPing: Enabled ARPPing timeout(secs): 900 ARPPing number of repetitions: 3 Status: Connected IPv4 address: <removed> IPv6 address: <removed> Enable/Disable: Enabled Addressing Type IPv4: DHCP ------DHCPv4------ Option 60 Vendor ID: meods00 Option 61 IAID: Option 61 DUID: Subnet Mask: <removed> Default Gateway: <removed> Option 125: DNS Servers: <removed> Remaining Lease Time(secs): <removed> ------DHCPv6------ Type: PrefixDelegation Prefix: <removed>/56 Preferred lifetime: 90000 Valid lifetime: 90000 Default gateway: <removed> DNS Servers: <removed> ----------------------------------------------Considering the above, I need to set Option 60, and also set the DHCPv6 options. Do you think that there are any other settings I should configure on the WAN interface?
thank you
-
@stealthmode VendorID might be the only setting needed - it might not. Sometimes not everything is outputted in Shell command like that. But try
-
Mmm, what did you run to get that? I can't decide if that's what the server sent rather than the client.
