Netgate 4100 slower at 2.5gbe than 1gbe

stephenw10

Does it actually link at 2.5G?

Do you see errors on the interface in Status > Interfaces?

Try reassigning WAN to one of the other igb ports and see if the issue follows it.

A Former User

I have tried multiple ports, the problem always follows. Here's the status with it forced to 2.5. I managed to get 300-something and 250-something with it set like this. I set it back to 1gb and got a 940 and a 939.

stephenw10

Hmm, not errors then.

Check the output of sysctl hw.igc and sysctl dev.igc.2. Could be a flow control issue.

Can you the status of the modem port or set anything at that end?

A Former User

@stephenw10

The only thing I can see in the modem related to ethernet is that it agrees, 2.5gb connection. The logs don't show anything at all, assume they must be related to the router functions that are bypassed when set to bridge mode.

I have no idea what I'm looking at in the output of these commands.

Shell Output - sysctl hw.igc
hw.igc.max_interrupt_rate: 20000
hw.igc.eee_setting: 1
hw.igc.sbp: 1
hw.igc.smart_pwr_down: 0
hw.igc.rx_abs_int_delay: 66
hw.igc.tx_abs_int_delay: 66
hw.igc.rx_int_delay: 0
hw.igc.tx_int_delay: 66
hw.igc.disable_crc_stripping: 0

Shell Output - sysctl dev.igc.2
dev.igc.2.wake: 0
dev.igc.2.interrupts.rx_desc_min_thresh: 0
dev.igc.2.interrupts.asserts: 21205157789
dev.igc.2.mac_stats.tso_txd: 0
dev.igc.2.mac_stats.tx_frames_1024_1522: 12870635006
dev.igc.2.mac_stats.tx_frames_512_1023: 117248314
dev.igc.2.mac_stats.tx_frames_256_511: 118770026
dev.igc.2.mac_stats.tx_frames_128_255: 373871075
dev.igc.2.mac_stats.tx_frames_65_127: 2318793523
dev.igc.2.mac_stats.tx_frames_64: 232229298
dev.igc.2.mac_stats.mcast_pkts_txd: 41
dev.igc.2.mac_stats.bcast_pkts_txd: 30221
dev.igc.2.mac_stats.good_pkts_txd: 16031547242
dev.igc.2.mac_stats.total_pkts_txd: 16031547242
dev.igc.2.mac_stats.good_octets_txd: 19566552685116
dev.igc.2.mac_stats.good_octets_recvd: 15444273234391
dev.igc.2.mac_stats.rx_frames_1024_1522: 10030708797
dev.igc.2.mac_stats.rx_frames_512_1023: 149340411
dev.igc.2.mac_stats.rx_frames_256_511: 133766002
dev.igc.2.mac_stats.rx_frames_128_255: 297433919
dev.igc.2.mac_stats.rx_frames_65_127: 4831425297
dev.igc.2.mac_stats.rx_frames_64: 179397977
dev.igc.2.mac_stats.mcast_pkts_recvd: 17616456
dev.igc.2.mac_stats.bcast_pkts_recvd: 2567
dev.igc.2.mac_stats.good_pkts_recvd: 15622072403
dev.igc.2.mac_stats.total_pkts_recvd: 15623300953
dev.igc.2.mac_stats.xoff_txd: 0
dev.igc.2.mac_stats.xoff_recvd: 0
dev.igc.2.mac_stats.xon_txd: 0
dev.igc.2.mac_stats.xon_recvd: 0
dev.igc.2.mac_stats.alignment_errs: 0
dev.igc.2.mac_stats.crc_errs: 0
dev.igc.2.mac_stats.recv_errs: 0
dev.igc.2.mac_stats.recv_jabber: 0
dev.igc.2.mac_stats.recv_oversize: 0
dev.igc.2.mac_stats.recv_fragmented: 0
dev.igc.2.mac_stats.recv_undersize: 0
dev.igc.2.mac_stats.recv_no_buff: 0
dev.igc.2.mac_stats.missed_packets: 0
dev.igc.2.mac_stats.defer_count: 0
dev.igc.2.mac_stats.sequence_errors: 0
dev.igc.2.mac_stats.symbol_errors: 0
dev.igc.2.mac_stats.collision_count: 0
dev.igc.2.mac_stats.late_coll: 0
dev.igc.2.mac_stats.multiple_coll: 0
dev.igc.2.mac_stats.single_coll: 0
dev.igc.2.mac_stats.excess_coll: 0
dev.igc.2.queue_rx_1.rx_irq: 0
dev.igc.2.queue_rx_1.rxd_tail: 243
dev.igc.2.queue_rx_1.rxd_head: 244
dev.igc.2.queue_rx_0.rx_irq: 0
dev.igc.2.queue_rx_0.rxd_tail: 667
dev.igc.2.queue_rx_0.rxd_head: 668
dev.igc.2.queue_tx_1.tx_irq: 0
dev.igc.2.queue_tx_1.txd_tail: 803
dev.igc.2.queue_tx_1.txd_head: 803
dev.igc.2.queue_tx_0.tx_irq: 0
dev.igc.2.queue_tx_0.txd_tail: 510
dev.igc.2.queue_tx_0.txd_head: 510
dev.igc.2.fc_low_water: 32752
dev.igc.2.fc_high_water: 32768
dev.igc.2.rx_control: 71335938
dev.igc.2.device_control: 1477707329
dev.igc.2.watchdog_timeouts: 0
dev.igc.2.rx_overruns: 0
dev.igc.2.link_irq: 392
dev.igc.2.dropped: 0
dev.igc.2.eee_control: 1
dev.igc.2.itr: 488
dev.igc.2.tx_abs_int_delay: 66
dev.igc.2.rx_abs_int_delay: 66
dev.igc.2.tx_int_delay: 66
dev.igc.2.rx_int_delay: 0
dev.igc.2.rs_dump: 0
dev.igc.2.reg_dump: General Registers
	CTRL	 58140641
	STATUS	 40780683
	CTRL_EXIT	 10000040

Interrupt Registers
	ICR	 00000000

RX Registers
	RCTL	 04408002
	RDLEN	 00004000
	RDH	 0000029c
	RDT	 0000029b
	RXDCTL	 02040808
	RDBAL	 6aa7e000
	RDBAH	 00000000

TX Registers
	TCTL	 a503f0fa
	TDBAL	 6aa62000
	TDBAH	 00000000
	TDLEN	 00004000
	TDH	 000001fe
	TDT	 000001fe
	TXDCTL	 0201011f
	TDFH	 00000000
	TDFT	 00000000
	TDFHS	 00000000
	TDFPC	 00000000


dev.igc.2.fc: 3
dev.igc.2.debug: -1
dev.igc.2.nvm: -1
dev.igc.2.iflib.rxq1.rxq_fl0.buf_size: 2048
dev.igc.2.iflib.rxq1.rxq_fl0.credits: 1023
dev.igc.2.iflib.rxq1.rxq_fl0.cidx: 244
dev.igc.2.iflib.rxq1.rxq_fl0.pidx: 243
dev.igc.2.iflib.rxq1.cpu: 1
dev.igc.2.iflib.rxq0.rxq_fl0.buf_size: 2048
dev.igc.2.iflib.rxq0.rxq_fl0.credits: 1023
dev.igc.2.iflib.rxq0.rxq_fl0.cidx: 668
dev.igc.2.iflib.rxq0.rxq_fl0.pidx: 667
dev.igc.2.iflib.rxq0.cpu: 0
dev.igc.2.iflib.txq1.r_abdications: 0
dev.igc.2.iflib.txq1.r_restarts: 0
dev.igc.2.iflib.txq1.r_stalls: 0
dev.igc.2.iflib.txq1.r_starts: 165433
dev.igc.2.iflib.txq1.r_drops: 0
dev.igc.2.iflib.txq1.r_enqueues: 165439
dev.igc.2.iflib.txq1.ring_state: pidx_head: 0638 pidx_tail: 0638 cidx: 0638 state: IDLE
dev.igc.2.iflib.txq1.txq_cleaned: 166649
dev.igc.2.iflib.txq1.txq_processed: 166689
dev.igc.2.iflib.txq1.txq_in_use: 42
dev.igc.2.iflib.txq1.txq_cidx_processed: 801
dev.igc.2.iflib.txq1.txq_cidx: 761
dev.igc.2.iflib.txq1.txq_pidx: 803
dev.igc.2.iflib.txq1.no_tx_dma_setup: 0
dev.igc.2.iflib.txq1.txd_encap_efbig: 0
dev.igc.2.iflib.txq1.tx_map_failed: 0
dev.igc.2.iflib.txq1.no_desc_avail: 0
dev.igc.2.iflib.txq1.mbuf_defrag_failed: 0
dev.igc.2.iflib.txq1.m_pullups: 0
dev.igc.2.iflib.txq1.mbuf_defrag: 0
dev.igc.2.iflib.txq1.cpu: 1
dev.igc.2.iflib.txq0.r_abdications: 0
dev.igc.2.iflib.txq0.r_restarts: 0
dev.igc.2.iflib.txq0.r_stalls: 0
dev.igc.2.iflib.txq0.r_starts: 142376
dev.igc.2.iflib.txq0.r_drops: 0
dev.igc.2.iflib.txq0.r_enqueues: 142377
dev.igc.2.iflib.txq0.ring_state: pidx_head: 1256 pidx_tail: 1256 cidx: 1256 state: IDLE
dev.igc.2.iflib.txq0.txq_cleaned: 143828
dev.igc.2.iflib.txq0.txq_processed: 143868
dev.igc.2.iflib.txq0.txq_in_use: 42
dev.igc.2.iflib.txq0.txq_cidx_processed: 508
dev.igc.2.iflib.txq0.txq_cidx: 468
dev.igc.2.iflib.txq0.txq_pidx: 510
dev.igc.2.iflib.txq0.no_tx_dma_setup: 0
dev.igc.2.iflib.txq0.txd_encap_efbig: 0
dev.igc.2.iflib.txq0.tx_map_failed: 0
dev.igc.2.iflib.txq0.no_desc_avail: 0
dev.igc.2.iflib.txq0.mbuf_defrag_failed: 0
dev.igc.2.iflib.txq0.m_pullups: 0
dev.igc.2.iflib.txq0.mbuf_defrag: 0
dev.igc.2.iflib.txq0.cpu: 0
dev.igc.2.iflib.override_nrxds: 0
dev.igc.2.iflib.override_ntxds: 0
dev.igc.2.iflib.use_logical_cores: 0
dev.igc.2.iflib.separate_txrx: 0
dev.igc.2.iflib.core_offset: 0
dev.igc.2.iflib.tx_abdicate: 0
dev.igc.2.iflib.rx_budget: 0
dev.igc.2.iflib.disable_msix: 0
dev.igc.2.iflib.override_qs_enable: 0
dev.igc.2.iflib.override_nrxqs: 0
dev.igc.2.iflib.override_ntxqs: 0
dev.igc.2.iflib.driver_version: 1
dev.igc.2.%parent: pci6
dev.igc.2.%pnpinfo: vendor=0x8086 device=0x15f3 subvendor=0x8086 subdevice=0x0000 class=0x020000
dev.igc.2.%location: slot=0 function=0 dbsf=pci0:6:0:0 handle=\_SB_.PCI0.PEX5.PXSX
dev.igc.2.%driver: igc
dev.igc.2.%desc: Intel(R) Ethernet Controller I225-V

stephenw10

You might try disabling flow control as a test: sysctl dev.igc.2.fc=0

What pfSense version is that?

A Former User

@stephenw10

I’ll give that a try and report back. It’s 24.03, I know I’m behind.

stephenw10

Ah, well I'd definitely try 24.11 then. I'm not aware of anything specific there that might address this but there have been a number of updates/fixes.

A Former User

@stephenw10
Yeah been meaning to do it but with two of us working from home and being a crazy busy time can’t even really afford weekend downtime. But I just kicked it off and will test changing flow control tomorrow.

A Former User

@stephenw10 Unfortunately neither the upgrade or changing flow control made any difference. Still get near 1gb when forced to 1gb, still get in the 300's when forced to 2.5gb.

stephenw10

How are you testing that exactly?

Can you grab a packet capture during the poor throughput?

A Former User

@stephenw10 I use a docker container called Speedtest Tracker which uses Speedtest.net. Running in docker and taking the browser out of the picture it seems to provide pretty consistent results. I'll have to look into capturing packets, should be doable, just have never had the need.

stephenw10

Hmm, the issues could be on the LAN side and are just hidden by limiting the throughput to 1G on the WAN.

Do you see any errors on the LAN interface?

You might try running an iperf3 test to or from pfSense itself and a LAN side client. Or running a a speedtest client test from pfSense directly so the LAN side is not involved.

A Former User

@stephenw10

Might be getting somewhere. I installed the speedtest widget from https://github.com/LeonStraathof/pfsense-speedtest-widget and get above the full provisioned speed as I would typically expect.

So I guess I don't understand why having more available bandwidth on the WAN interface would slow down the LAN? Don't see any errors but the interrupts seems high?

dennypage

@matt_m said in Netgate 4100 slower at 2.5gbe than 1gbe:

So I guess I don't understand why having more available bandwidth on the WAN interface would slow down the LAN?

Lack of flow control on either interface can cause this. I have 2.5Gb link on WAN (provisioned @ 2Gb down), and 10Gb link on the LAN interface. If I turn off flow control on the LAN, speed tests go very, very badly.

A Former User

I did some more testing.

If I set the LAN interface to 1000Gb I get most of the speed back. Tests in the high 800s, still notably lower than normal.
I tried all combinations of flow control on the LAN and WAN interfaces, doesn't seem to have any impact.
I enabled flow control on my Unifi network. At 2.5gb it doesn't seem to have any impact or maybe made things worse.
Flow control enabled everywhere, LAN at 2.5, WAN at 1, it seemed to be staying in the 800s
Back to flow control disabled in Unifi, enabled everywhere in pfSense, LAN at 2.5, WAN at 1, its back to the mid 900's.

Something about the router or my configuration of the router is an issue.

A Former User

One additional test, to rule out the SFP to RJ45 module, I have a small Netgear unmanaged 2.5gb switch sitting unused. I connected the LAN interface and the Proxmox host running my docker server directly to the 2.5gb switch and set the WAN back to 2.5 and didn't do any better than through all the Unifi equipment. I'll also add that I recently upgraded my proxmox host and saw these issues with the old host so its not that.

stephenw10

Yeah check the sysctl outputs for the LAN side NIC.

Try an iperf test between pfSense and a LAN side client, make sure you can actually pass >1G there.

A Former User

@stephenw10 had trouble getting iperf installed—just seemed to stall out. Figure a reboot was in order but couldn’t take down the network since we were working then headed out of town.

I have been intending to upgrade my switches to 2.5gb and picked up a Unifi Pro Max 24 during our trip. That will eliminate the GBIC to RJ45 adapter I've been using. I don’t expect that to resolve the issue but it’s something that’s been on my list for a while and will give me the ability to set up a 2.5gb connection from the router to my Docker machine for testing and will let a couple other machines take advantage of higher speeds. That also means I need to resolve this one way or another.

I’ve stumbled upon 1-2 other posts in dusty corners of the internet that might be describing the same issue but none with any resolution.

stephenw10

What switch do you have on the LAN side currently? Is it linked at 2.5G to the pfSense LAN and 1G to the clients?

Try setting the LAN side link to 1G when the WAN at 2.5G so the bandwidth change is in pfSense not the switch.

If it's in the switch you pretty much need flowcontrol active to avoid buffer overruns.