Unexpected alias behaviour - two ranges / size limits with FQDN

[tinfoilmatt]

@SteveITS said in Unexpected alias behaviour - two ranges:

I just meant to read my whole post

I would hope anybody participating here and on the entire forum—nay, the entire Internet—thoroughly reads and considers in earnest any communtication directed at them by a fellow human being.

But back to topic at-hand, anything you did today is preempted by the fact that you didn't start with...

[in Unexpected alias behaviour - two ranges:]

I created a VM with 2.8.1.
I used easyrule to allow access on WAN.
I bypassed the GUI setup wizard.

...like you did yesterday. (Some people refer to this methodology colloquially as 'blowing everything out and starting over.') In other words you didn't even consistently recreate your own test.

I could break any system with some formulation of rm or system-specific equivalent. What does that tell anyone?

[stephenw10]

@tinfoilmatt said in Unexpected alias behaviour - two ranges:

I would hope anybody participating here and on the entire forum—nay, the entire Internet—thoroughly reads and considers in earnest any communtication directed at them by a fellow human being.

[tinfoilmatt]

@stephenw10 Hey, at least you're getting paid to placate this behavior. I'm only here to have fun!

[Patch]

@SteveITS
After more testing I suspect the root cause of the bug investigated in this thread is

• An alias containing one or more FQDN is limited to a little over 512 entries (total across all such aliases), not the 5000 per alias limit suggested in the manual.
• if you go over that limit further alias table updates are blocked for all aliases

For the duplicate removal but not restored bug discovered again in this thread, and referenced in your thread, I can't see that being resolved any time soon. Learning how best to live with it is more sensible imo.

Easy bug trigger

Tested in a clean pfsense v2.8.1 install, enable WAN GUI access. Save that configuration as baseline. Done to ensure easy repeatability and reduce the validity of the shooting the messenger crap.

The easiest way of triggering the bug is entering the following 1024 consecutive element alias -> 473 element are shown in the corresponding alias table.

Random IP addresses & lower bound

To put a bound on the lower limit and confirm sequential IP addresses are irrelevant
Reload the baseline configuration and enter the a 513 element alias such as the following, -> 514 elements are shown in the corresponding alias table

Reload the baseline configuration and enter a 1025 element alias (using the method illustrated above) -> 473 element are shown in the corresponding alias table. Which is exactly the same as the sequential IP initial test case. Waiting longer, Filter reload and "killall filterdns" all make no difference.

Limit per alias or total record count

To illustrate the limit depends on the load implied by other alias
Restore the baseline configuration
Enter Alias like IP_set1 with 50 IP + FQDN x1 as shown below -> 52 records in Alias table

Enter Alias like IP_set2 with 50 IP + FQDN x1 using the same method (mine started 202.) -> 52 records shown in the alias table

Now again try and enter IP_set3 with 512 IP + FQDN x1 as shown below -> zero records. After several filter reloads 271 records. Waiting longer, Filter reload and "killall filterdns" all make no difference.
Which contrasts with the 514 records when no other aliases were entered.

Limit for "mixed mode" alias or also pure FQDN

To investigate if using explicit IP addresses vs FQDN addresses matter
Reload the baseline configuration and enter a 1024 FQDN, I copied the first 1024 entires form pfblocker. -> 569 records after wait about 1 hour and lots of filter reloads. After which

• "killall filterdns" -> No matching processes were found
• create an Test_loaded containing a single FQDN -> empty alias table

Which strongly suggests "mixed mode" alias are no different to pure FQDN aliases, just testing takes longer.

[Patch]

Updated above post to investigate if using explicit IP addresses vs FQDN records matters
Updated title to more accurately describe root cause evident in hind sight

[tinfoilmatt]

@Patch said in Unexpected alias behaviour - two ranges / size limits with FQDN:

Easy bug trigger
[ . . . ]
The easiest way of triggering the bug is entering the following 1024 consecutive element alias -> 473 element are shown in the corresponding alias table.

I can confirm this behavior.

[tinfoilmatt]

I am holding here despite the...

Aliases become Tables when loaded into the active firewall ruleset. The contents displayed on this page reflect the current addresses inside tables used by the firewall.

...advisory.

Please let me know if there's something I can/should do next that would further assist the thread.

[tinfoilmatt]

The 473 records are sequential from 123.123.120.0 through 123.123.121.216.

[stephenw10]

Hmm, I don't think this is a numerical limit. It seems more like a function of timing to me. But either way I would bet the root issue is in filterdns.

[Patch]

@bbcan177 You have been dealing with far larger sets of IP addresses and FQDN in pfsense. How have you been working around

1. The limitation in cumulative number of entries in aliases containing a FQDN as described above

2. The possibly related consequence of using incremental alias update with duplicate removal but then using incremental IP removal without restoration of he removed duplicate as per https://redmine.pfsense.org/issues/13792 and possibly https://redmine.pfsense.org/issues/9296 and https://redmine.pfsense.org/issues/13793

The short term fix

1. is relatively simple, just document the limit, add it to redmine and say it's being worked on. Something I can easily work with.

2. is more difficult as that bug essential requires the user ensure all alias containing FQDN are always non intersecting (never trigger duplicate removal). Which severely limits the value of alias for me.

The longer term fix maybe more difficult as it maybe a program architecture limit rather than a coding bug.

• The limit for "mixed mode" aliases may be resolvable by internally processing the constants (explicitly specified IP addresses) separately to the variable entries (FQDN) then combining the two "sub aliases". The constant portion only need to be evaluated at alias editing or program boot up. Optimisation to group longer runs of consecutive addresses into CIDR prefix notation would be possible.

• Regression analysis I suspect would show the progressive slowing of alias update and eventual lock up investigated in this thread is a result of earlier work to try and avoid the limitations of implicit duplicate removal addressed in https://redmine.pfsense.org/issues/9296

• A solution maybe to pre process so addition to filterdns are only made when the duplicate count for that address goes from 0->1 and similalry deletion from filterdns are only made when the duplicate count for that address goes from 1->0. Other duplicate count transitions 1<->2<->3 etc result in no filterdns calls.

• Alternatively incremental deletes could be avoided completely by all updated being done by a full alias rebuild to a temporary variable then full replacement of the old with the new.

None of which sound trivial to me.

[stephenw10]

pfBlocker uses URL table aliases which are not limited to 3000 entries like other alias types. But as I said I don't think that's what we're hitting here.