Squid3 - New GUI with sync, normal and reverse proxy

[marcelloc]

@athompso:

1. can anyone tell me if there is a way to get this pkg to listen on a CARP IP (or even just listen on all interfaces!), and

Listen squid on loopback(lo0) and create nat rules from carp address to 127.0.0.1

2.1 gui framework has the listen all as well listen on virtual ips, so squid3 on pfsense 2.1 will have this option and no need to workaround with nats.

[athompso]

@jimp:

Unless the cache and connection state are shared between squid instances, you don't want it binding on a CARP VIP. It makes little sense to have the traffic leave from a shared IP and shared pf states when the actual connections in squid are independent, even if the config is synchronized.
The point of syncing the config is so the slave can take over, and it can, you just can't seamlessly fail over 100% in squid. Even if the states were to sync over it doesn't matter, the squid process itself would have no knowledge of the connection.

I don't particularly care about seamless failover, I just want to avoid using PAC.  If I have a redundant pair of firewalls, I use the CARP VIP as my default gateway from the inside.  The way it's set up right now, I have to point all the clients at one firewall or the other's physical (LAN) IP address.  So if that firewall dies, I lose the ability to browse the web without manually reconfiguring each client…?  Whereas if squid was bound to the CARP VIP, any in-flight HTTP transactions would fail, but at least I wouldn't have to go around and reconfigure every client.  Is there some other mechanism I don't know about?

@marcelloc:

Listen squid on loopback(lo0) and create nat rules from carp address to 127.0.0.1
2.1 gui framework has the listen all as well listen on virtual ips, so squid3 on pfsense 2.1 will have this option and no need to workaround with nats.

That approach hadn't occurred to me - trying it now to see if it works, but I don't expect problems.
However, as to the second point: I am using 2.1-BETA, and I do not see any such option.  ("squid3" package, version "beta 3.1.20 pkg 2.0.5_3")

-Adam

[jimp]

NAT is indeed the easy solution there.

[marcelloc]

@athompso:

However, as to the second point: I am using 2.1-BETA, and I do not see any such option.  ("squid3" package, version "beta 3.1.20 pkg 2.0.5_3")

I said it will, I did not included the code to squid package yet  ;)

[hisoka01]

Hi, my squid cannot start :'(, here is the message in cache.log:

2012/08/28 23:09:44| Accepting  HTTP connections at [::]:3128, FD 29.
2012/08/28 23:09:44| HTCP Disabled.
2012/08/28 23:09:44| Ready to serve requests.
2012/08/28 23:09:44| WARNING: ssl_crtd #1 (FD 19) exited
2012/08/28 23:09:44| WARNING: ssl_crtd #2 (FD 21) exited
2012/08/28 23:09:44| WARNING: ssl_crtd #3 (FD 23) exited
(ssl_crtd): Uninitialized SSL certificate database directory: /var/squid/lib/ssl_db. To initialize, r
un "ssl_crtd -c -s /var/squid/lib/ssl_db".
2012/08/28 23:09:44| WARNING: ssl_crtd #4 (FD 25) exited
2012/08/28 23:09:44| Too few ssl_crtd processes are running
2012/08/28 23:09:44| storeDirWriteCleanLogs: Starting...
2012/08/28 23:09:44|   Finished.  Wrote 0 entries.
2012/08/28 23:09:44|   Took 0.00 seconds (  0.00 entries/sec).
FATAL: The ssl_crtd helpers are crashing too rapidly, need help!

Squid Cache (Version 3.1.20): Terminated abnormally.
CPU Usage: 0.092 seconds = 0.061 user + 0.031 sys
Maximum Resident Size: 10532 KB
Page faults with physical i/o: 0
(ssl_crtd): Uninitialized SSL certificate database directory: /var/squid/lib/ssl_db. To initialize, r
un "ssl_crtd -c -s /var/squid/lib/ssl_db".

I have tried both squid 2 & 3, both got the same message ::)
Also it seems there is no "ssl_crtd" exist in my system…so I cannot try to run the command :o
Do you have any suggestion..? :'(

Thanks

[marcelloc]

I have this dir on my squid3 install.

What are you trying to configure?

ls -la /var/squid/lib/
total 6
drwxr-xr-x  3 proxy  proxy  512 Apr 14 02:17 .
drwxrwxr-x  7 proxy  proxy  512 Apr 14 02:17 ..
drwxr-xr-x  2 proxy  proxy  512 Apr 14 02:17 ssl_db

[Hobby-Student]

Hey guys,

I have a strange problem regarding reverse proxy and authentification with Certificates… The package itself is working as expected and without certs needed to authenticate I can open all services (owa, msas, rpc).

Now here it comes: (all IP's, ports and url's are renamed for security reasons  ;) )

if i use this line in my squid.conf:

https_port xxx.xxx.xxx.xxx:Port cert=/website.crt key=/website.key defaultsite=this.website.me vhost

everything works as expected. I get my login page… but if I use this one:

https_port xxx.xxx.xxx.xxx:Port cert=/website.crt key=/website.key defaultsite=this.website.me clientca=/CA.crt cafile=/CA.crt capath=/ sslcontext=id vhost

I get asked for my client cert and then "page cannot be found" with this in squid logs:

clientNegotiateSSL: Error negotiating SSL connection on FD 17: error:0D0C50A1:asn1 encoding routines:ASN1_item_verify:unknown message digest algorithm (1/-1)

My CA is created with SHA512… So the clients are too ;)
When I do

openssl list-message-digest-commands

on my pfsense shell, I get

md2
md4
md5
mdc2
rmd160
sha
sha1

But with openssl speed, sha512 is listed!

What I found so far is, that somewhere in the squid source this line should be added

OpenSSL_add_all_algorithms()

somwhere like

src/ssl_support.*
function: ssl_initialize(void)

Due to the lack of time, I wasn't able to get deeper inside… Does someone has an idea?!

@marcelloc:
If this needs to be posted somewhere else, please let mo know. If I understand this package right, you are compiling squid on your own?! So this could be solved easily...

Kind regards

EDIT:
found it in src/ssl_support.cc, line 593

SSL_load_error_strings();
SSLeay_add_ssl_algorithms();

what i found by google, there should also be called: OpenSSL_add_all_algorithms()

@marcelloc:
possible?

[marcelloc]

@Hobby-Student:

@marcelloc:
If this needs to be posted somewhere else, please let mo know. If I understand this package right, you are compiling squid on your own?! So this could be solved easily…

No more  :(

Packages now must be only compiled and provided by official repo, you can compile it on 8.1 freebsd, create the package and then install on your system.

Core team are really busy these days. I'm waiting some packages to be recompiled too. After this, I can continue package development and testing.

these are current squid3 compile options available on ports

SQUID_KERB_AUTH      Install Kerberos authentication helper

SQUID_LDAP_AUTH      Install LDAP authentication helpers 

SQUID_NIS_AUTH      Install NIS/YP authentication helpers

SQUID_SASL_AUTH      Install SASL authentication helpers 

SQUID_IPV6          Enable IPv6 support                                 

SQUID_DELAY_POOLS    Enable delay pools                   

SQUID_SNMP          Enable SNMP support                   

SQUID_SSL            Enable SSL support for reverse proxies

SQUID_SSL_CRTD      Enable SSL certificate daemon         

SQUID_PINGER        Install the icmp helper               

SQUID_DNS_HELPER    Use the old 'dnsserver' helper       

SQUID_HTCP          Enable HTCP support                   

SQUID_VIA_DB        Enable forward/via database           

SQUID_CACHE_DIGESTS  Enable cache digests                 

SQUID_WCCP          Enable Web Cache Coordination Prot. v1

SQUID_WCCPV2        Enable Web Cache Coordination Prot. v2

SQUID_STRICT_HTTP    Be strictly HTTP compliant           

SQUID_IDENT          Enable ident (RFC 931) lookups       

SQUID_REFERER_LOG    Enable Referer-header logging         

SQUID_USERAGENT_LOG  Enable User-Agent-header logging     

SQUID_ARP_ACL        Enable ACLs based on ethernet address 

SQUID_IPFW          Enable transparent proxying with IPFW 

SQUID_PF            Enable transparent proxying with PF   

SQUID_IPFILTER      Enable transp. proxying with IPFilter 

SQUID_FOLLOW_XFF    Follow X-Forwarded-For headers       

SQUID_ECAP          En. loadable content adaptation modules

SQUID_ICAP          Enable ICAP client functionality     

SQUID_ESI            Enable ESI support (experimental)     

SQUID_AUFS          Enable the aufs storage scheme       

SQUID_COSS          Enable COSS (currently not available) 

SQUID_KQUEUE        Use kqueue(2) (experimental)         

SQUID_LARGEFILE      Support log and cache files >2GB     

SQUID_STACKTRACES    Create backtraces on fatal errors     

SQUID_DEBUG          Enable debugging options

[Hobby-Student]

@marcelloc:

Packages now must be only compiled and provided by official repo, you can compile it on 8.1 freebsd, create the package and then install on your system.

Core team are really busy these days. I'm waiting some packages to be recompiled too. After this, I can continue package development and testing.

these are current squid3 compile options available on ports

So if I would have a FreeBSD 8.1, download squid sources and build it with all the options marked in your post, we could run the binaries on pfsense?

EDIT:
could I use squid 3.2.1 source? or won't this one run on pfsense?

EDIT #2:
downloading freebsd 8.1 i386. will try to get things work.

@marcelloc:
please let me know, which version of squid I should compile. 3.1.19, 3.1.20 or 3.2.1?

[marcelloc]

The best way is to use freebsd ports to compile.

Portsnap fetch
Portsnap extract

CD /usr/ports/www/squid31
make package

[Hobby-Student]

why don't we use version 3.2.1?

[marcelloc]

It's not on ports yet. To create the package for 3.2.1 we need first a port for it.
We can try to create it based on 3.1.20 dir

[Hobby-Student]

did it.

here we go:
compiled squid 3.1.20 with ports on FreeBSD 8.1. I modified the source and now squid is able to authenticate users with certs (all digests) in reverse mode… i try to find some place to upload the binaries.

EDIT:
forgot to ask… are you interested in including "my" squid version? I just added the mentioned one line in the source....

[marcelloc]

Post what you did. Maybe I can send it as a feature request to squid port maintained @ freebsd

[Hobby-Student]

this is what i did:

source file: ssl_support.cc, around line 593 (in squid 3.2.1 the file is located in "ssl" subdir named "support.cc")

function: ssl_initialize(void)

original:

SSL_load_error_strings();
SSLeay_add_ssl_algorithms();

to:

SSL_load_error_strings();
OpenSSL_add_all_algorithms();
SSLeay_add_ssl_algorithms();

would you like to include my binaries in your package?

[marcelloc]

@namek:

I am using this mainly for content filtering/caching/logging…

squid3 has some new features on it's gui too, check it on a test machine first.

[marcelloc]

@namek:

Oh yes, one the features I found was 'patch captive portal' - which I believe that if the users are on a proxy they will not be able to bypass captive portal?

yes. I did it based on some topics on this forum with problems on using captive and squid.

@namek:

And ofcourse there are more features..are many users using this in production? as you have marked it as "Beta"
another striking feature are the realtime logs integrated in the GUI itself. So i believe that somewhat eliminates the need of using the 'realtime' feature of both sarg and lightsquid…

The realtime tab on squid3 package is to help debug access while using squid and squidguard.

[TyperX]

Hi all, i have install squid3 package and just use standard config, squid reverse not config yet. After install i have problem to access banking website and got error msg from squid Unable to determine IP address from host name "www.cimbclicks.com.my". How can i solve this problem? Below my squid config.

# This file is automatically generated by pfSense
# Do not edit manually !
http_port 192.168.10.1:3128
http_port 127.0.0.1:3128 intercept
icp_port 7
dns_v4_first on
pid_filename /var/run/squid.pid
cache_effective_user proxy
cache_effective_group proxy
error_default_language English
icon_directory /usr/local/etc/squid/icons
visible_hostname localhost
cache_mgr ikhwans@kbc.com.my
access_log /var/squid/logs/access.log
cache_log /var/squid/logs/cache.log
cache_store_log none
sslcrtd_children 0
logfile_rotate 0
shutdown_lifetime 3 seconds
# Allow local network(s) on interface(s)
acl localnet src  192.168.10.0/24
uri_whitespace strip

acl dynamic urlpath_regex cgi-bin ?
cache deny dynamic
cache_mem 32 MB
maximum_object_size_in_memory 64 KB
memory_replacement_policy heap GDSF
cache_replacement_policy heap LFUDA
cache_dir ufs /var/squid/cache 1000 16 256
minimum_object_size 0 KB
maximum_object_size 4 KB
offline_mode offcache_swap_low 90
cache_swap_high 95

# No redirector configured

#Remote proxies

# Setup some default acls
acl allsrc src all
acl localhost src 127.0.0.1/32
acl safeports port 21 70 80 210 280 443 488 563 591 631 777 901 8888 3128 1025-65535 
acl sslports port 443 563 8888 
acl manager proto cache_object
acl purge method PURGE
acl connect method CONNECT

http_access allow manager localhost

# Allow external cache managers
acl ext_manager src 127.0.0.1
acl ext_manager src 192.168.10.1
acl ext_manager src 
http_access allow manager ext_manager

http_access deny manager
http_access allow purge localhost
http_access deny purge
http_access deny !safeports
http_access deny CONNECT !sslports

# Always allow localhost connections
http_access allow localhost

request_body_max_size 0 KB
delay_pools 1
delay_class 1 2
delay_parameters 1 -1/-1 -1/-1
delay_initial_bucket_level 100
delay_access 1 allow allsrc

# Reverse Proxy settings

# Package Integration
redirect_program /usr/local/bin/squidGuard -c /usr/local/etc/squidGuard/squidGuard.conf
redirector_bypass on
redirect_children 3

# Custom options

# Setup allowed acls
# Allow local network(s) on interface(s)
http_access allow localnet
# Default block all to be sure
http_access deny allsrc

[marcelloc]

Dns v4 first turned on was the latest workaround for this https issue.

Did you tried to stop and start squid after this change?

[TyperX]

It's working now, i have restart the pfsense. Thanks for the help  ;D