OpenVPN Cliet Cannot Access LAN OpenVPN
-
sullrich
Here i paste the output of each command.
ifconfig
sis0: flags=8843 <up,broadcast,running,simplex,multicast>mtu 1500
options=8 <vlan_mtu>inet 10.20.20.1 netmask 0xffffff00 broadcast 10.20.20.255
inet6 fe80::200:24ff:fec6:dae8%sis0 prefixlen 64 scopeid 0x1
ether 00:00:24:c6:da:e8
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
sis1: flags=8843 <up,broadcast,running,simplex,multicast>mtu 1500
options=8 <vlan_mtu>inet 10.10.100.223 netmask 0xffffff00 broadcast 10.10.100.255
inet6 fe80::200:24ff:fec6:dae9%sis1 prefixlen 64 scopeid 0x2
ether 00:00:24:c6:da:e9
media: Ethernet autoselect (100baseTX)
status: active
sis2: flags=8842 <broadcast,running,simplex,multicast>mtu 1500
options=8 <vlan_mtu>ether 00:00:24:c6:da:ea
media: Ethernet autoselect (none)
status: no carrier
lo0: flags=8049 <up,loopback,running,multicast>mtu 16384
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
enc0: flags=41 <up,running>mtu 1536
pfsync0: flags=41 <up,running>mtu 2020
pfsync: syncdev: lo0 syncpeer: 224.0.0.240 maxupd: 128
pflog0: flags=100 <promisc>mtu 33208
tun0: flags=8051 <up,pointopoint,running,multicast>mtu 1500
inet6 fe80::200:24ff:fec6:dae8%tun0 prefixlen 64 scopeid 0x8
inet 10.20.2.1 –> 10.20.2.2 netmask 0xffffffff
Opened by PID 6416
ng0: flags=8890 <pointopoint,noarp,simplex,multicast>mtu 1500
ng1: flags=8890 <pointopoint,noarp,simplex,multicast>mtu 1500
ng2: flags=8890 <pointopoint,noarp,simplex,multicast>mtu 1500
ng3: flags=8890 <pointopoint,noarp,simplex,multicast>mtu 1500
ng4: flags=8890 <pointopoint,noarp,simplex,multicast>mtu 1500
ng5: flags=8890 <pointopoint,noarp,simplex,multicast>mtu 1500
ng6: flags=8890 <pointopoint,noarp,simplex,multicast>mtu 1500
ng7: flags=8890 <pointopoint,noarp,simplex,multicast>mtu 1500
ng8: flags=8890 <pointopoint,noarp,simplex,multicast>mtu 1500
ng9: flags=8890 <pointopoint,noarp,simplex,multicast>mtu 1500
ng10: flags=8890 <pointopoint,noarp,simplex,multicast>mtu 1500
ng11: flags=8890 <pointopoint,noarp,simplex,multicast>mtu 1500
ng12: flags=8890 <pointopoint,noarp,simplex,multicast>mtu 1500
ng13: flags=8890 <pointopoint,noarp,simplex,multicast>mtu 1500
ng14: flags=8890 <pointopoint,noarp,simplex,multicast>mtu 1500
ng15: flags=8890 <pointopoint,noarp,simplex,multicast>mtu 1500
ng16: flags=8890 <pointopoint,noarp,simplex,multicast>mtu 1500cat /tmp/rules.debug | grep tun
pass out quick on tun0 all keep state label "let out anything from firewall host itself openvpn"
pass in quick on tun0 all keep state label "let out anything from firewall host itself openvpn"cat /tmp/rules.debug | grep tap
#</pointopoint,noarp,simplex,multicast></pointopoint,noarp,simplex,multicast></pointopoint,noarp,simplex,multicast></pointopoint,noarp,simplex,multicast></pointopoint,noarp,simplex,multicast></pointopoint,noarp,simplex,multicast></pointopoint,noarp,simplex,multicast></pointopoint,noarp,simplex,multicast></pointopoint,noarp,simplex,multicast></pointopoint,noarp,simplex,multicast></pointopoint,noarp,simplex,multicast></pointopoint,noarp,simplex,multicast></pointopoint,noarp,simplex,multicast></pointopoint,noarp,simplex,multicast></pointopoint,noarp,simplex,multicast></pointopoint,noarp,simplex,multicast></pointopoint,noarp,simplex,multicast></up,pointopoint,running,multicast></promisc></up,running></up,running></up,loopback,running,multicast></vlan_mtu></broadcast,running,simplex,multicast></vlan_mtu></up,broadcast,running,simplex,multicast></full-duplex></vlan_mtu></up,broadcast,running,simplex,multicast>
-
That is strange. You should have two tun devices (tun0 and tun1) from what I understand.
Let me speak with Fernando.
-
sullrich
Ok..For your info, my pfsense running on version 1.0.1-SNAPSHOT-03-27-2007.
-
Just for brevity sake, please upgrade to the latest and retest.
-
sullrich
I've do add the command "route-method exe" and "route-delay 2" at the Client Configuration file. And u know what…The client can access the OpenVPN Server and also the LAN of it.
But it still appear some errors on it..
"
Tue May 15 09:03:45 2007 us=886389 Notified TAP-Win32 driver to set a DHCP IP/netmask of 10.20.2.10/255.255.255.252 on interface {3890476B-0667-4DE4-832E-0FB996C0862A} [DHCP-serv: 10.20.2.9, lease-time: 31536000]
Tue May 15 09:03:45 2007 us=891004 NOTE: FlushIpNetTable failed on interface [65539] {3890476B-0667-4DE4-832E-0FB996C0862A} (status=1413) : Invalid index.
Tue May 15 09:03:47 2007 us=971039 TEST ROUTES: 0/0 succeeded len=2 ret=0 a=0 u/d=down
Tue May 15 09:03:47 2007 us=972576 Route: Waiting for TUN/TAP interface to come up…
Tue May 15 09:03:50 2007 us=42204 TEST ROUTES: 2/2 succeeded len=2 ret=1 a=0 u/d=up
Tue May 15 09:03:50 2007 us=43927 route ADD 10.20.20.0 MASK 255.255.255.0 10.20.2.9
Tue May 15 09:03:50 2007 us=657776 route ADD 10.20.2.1 MASK 255.255.255.255 10.20.2.9
Tue May 15 09:03:50 2007 us=713620 Initialization Sequence Completed
"What is actually the error…
Can i just ignoring it or i've to do something to fix it. The client now can ping the LAN after i adding the command....
One more...users actually can access the OpenVPN simultaneous? Like PPTP, the maximum concurrent connections is 16.....
-
upgrade to pfsense 1.2 there are a ziljun bugs been fixt between 1.0.1 and 1.2
also for openvpn -
Hi all,
Just now i got another errors…
"
Tue May 15 14:01:51 2007 us=771310 TAP-WIN32 device [vpn] opened: \.\Global{3890476B-0667-4DE4-832E-0FB996C0862A}.tap
Tue May 15 14:01:51 2007 us=772634 TAP-Win32 Driver Version 8.4
Tue May 15 14:01:51 2007 us=772659 TAP-Win32 MTU=1500
Tue May 15 14:01:51 2007 us=772692 Notified TAP-Win32 driver to set a DHCP IP/netmask of 10.20.2.10/255.255.255.252 on interface {3890476B-0667-4DE4-832E-0FB996C0862A} [DHCP-serv: 10.20.2.9, lease-time: 31536000]
Tue May 15 14:01:51 2007 us=774597 NOTE: FlushIpNetTable failed on interface [65539] {3890476B-0667-4DE4-832E-0FB996C0862A} (status=1413) : Invalid index.
Tue May 15 14:01:54 2007 us=29738 TEST ROUTES: 0/0 succeeded len=2 ret=0 a=0 u/d=down
Tue May 15 14:01:54 2007 us=29987 Route: Waiting for TUN/TAP interface to come up…
Tue May 15 14:01:56 2007 us=264608 TEST ROUTES: 0/0 succeeded len=2 ret=0 a=0 u/d=down
Tue May 15 14:01:56 2007 us=264882 Route: Waiting for TUN/TAP interface to come up...
Tue May 15 14:01:57 2007 us=497527 TEST ROUTES: 2/2 succeeded len=2 ret=1 a=0 u/d=up
Tue May 15 14:01:57 2007 us=497788 route ADD 10.20.20.0 MASK 255.255.255.0 10.20.2.9
The route addition failed: The parameter is incorrect.
Tue May 15 14:01:57 2007 us=561374 route ADD 10.20.2.1 MASK 255.255.255.255 10.20.2.9
The route addition failed: The parameter is incorrect.
Tue May 15 14:01:57 2007 us=622633 Initialization Sequence Completed
"jeroen234
I'll upgrade to pfsense 1.2 later. But what's actually they fix in the 1.2 version for OpenVPN?
-
There's no limit imposed by the pfSense OpenVPN implementation. There might be a limit in OpenVPN or this could also be limited by the maximum number of tun interfaces at a given moment in FreeBSD. But this limit is certainly greater than 2.
This could be a broken client, perhaps. If you're confortable with Unix, log into the pfSense shell, kill the OpenVPN daemon (openvpn process), edit /var/etc/openvpn_server0.conf and change the line that says "daemon" to "verb 4". Then start OpenVPN daemon by running "openvpn –config /var/etc/openvpn_server0.conf". Then try to connect from the clients.
-
There's no limit imposed by the pfSense OpenVPN implementation. There might be a limit in OpenVPN or this could also be limited by the maximum number of tun interfaces at a given moment in FreeBSD. But this limit is certainly greater than 2.
This could be a broken client, perhaps. If you're confortable with Unix, log into the pfSense shell, kill the OpenVPN daemon (openvpn process), edit /var/etc/openvpn_server0.conf and change the line that says "daemon" to "verb 4". Then start OpenVPN daemon by running "openvpn –config /var/etc/openvpn_server0.conf". Then try to connect from the clients.
fernandotcl
How to kill OpenVPN daemon in pfsense..I'm not familiar with it..
I try to do edit /var/etc/openvpn_server0.conf configuration file without killing the OpenVPN daemon process.. but it appear some errors after i start running it back..
**"
openvpn –config /var/etc/openvpn_server0.conf
Options error: Unrecognized option or missing parameter(s) in /var/etc/openvpn_server0.conf:15: lport (2.0.6)
Use --help for more information.
"** -
Hi all,
I had already upgrade to 1.2-BETA-1 version on Friday. And i already retest the OpenVPN. But the error is still the same…
"
Mon May 21 09:34:09 2007 us=379704 TAP-WIN32 device [vpn] opened: \.\Global{3890476B-0667-4DE4-832E-0FB996C0862A}.tap
Mon May 21 09:34:09 2007 us=379930 TAP-Win32 Driver Version 8.4
Mon May 21 09:34:09 2007 us=379950 TAP-Win32 MTU=1500
Mon May 21 09:34:09 2007 us=379980 Notified TAP-Win32 driver to set a DHCP IP/netmask of 10.20.2.10/255.255.255.252 on interface {3890476B-0667-4DE4-832E-0FB996C0862A} [DHCP-serv: 10.20.2.9, lease-time: 31536000]
Mon May 21 09:34:09 2007 us=663039 NOTE: FlushIpNetTable failed on interface [65539] {3890476B-0667-4DE4-832E-0FB996C0862A} (status=1413) : Invalid index.
Mon May 21 09:34:11 2007 us=876367 TEST ROUTES: 0/0 succeeded len=2 ret=0 a=0 u/d=down
Mon May 21 09:34:11 2007 us=876411 Route: Waiting for TUN/TAP interface to come up…
Mon May 21 09:34:14 2007 us=46950 TEST ROUTES: 2/2 succeeded len=2 ret=1 a=0 u/d=up
Mon May 21 09:34:14 2007 us=47002 route ADD 10.20.20.0 MASK 255.255.255.0 10.20.2.9
The route addition failed: The parameter is incorrect.
Mon May 21 09:34:14 2007 us=110468 route ADD 10.20.2.1 MASK 255.255.255.255 10.20.2.9
The route addition failed: The parameter is incorrect.
SYSTEM ROUTING TABLE
0.0.0.0 0.0.0.0 10.10.30.31 p=0 i=65540 t=0 pr=3 a=0 h=0 m=20/20/20/10/3
10.10.0.0 255.255.0.0 10.10.100.19 p=0 i=65540 t=0 pr=2 a=0 h=0 m=20/20/20/1/3
10.10.100.19 255.255.255.255 127.0.0.1 p=0 i=1 t=0 pr=2 a=0 h=0 m=20/20/20/1/1
10.20.2.10 255.255.255.255 127.0.0.1 p=0 i=1 t=0 pr=2 a=0 h=0 m=30/30/30/1/1
10.255.255.255 255.255.255.255 10.10.100.19 p=0 i=65540 t=0 pr=2 a=0 h=0 m=20/20/20/1/3
127.0.0.0 255.0.0.0 127.0.0.1 p=0 i=1 t=0 pr=2 a=0 h=0 m=1/1/1/1/1
127.0.0.1 255.255.255.255 127.0.0.1 p=0 i=1 t=0 pr=2 a=0 h=0 m=1/1/1/1/1
224.0.0.0 240.0.0.0 10.10.100.19 p=0 i=65540 t=0 pr=2 a=0 h=0 m=20/20/20/1/3
255.255.255.255 255.255.255.255 10.10.100.19 p=0 i=65540 t=0 pr=2 a=0 h=0 m=1/1/1/1/3
SYSTEM ADAPTER LIST
TAP-Win32 Adapter V8 - Virtual Machine Network Services Driver
Index = 65539
GUID = {3890476B-0667-4DE4-832E-0FB996C0862A}
IP = 10.20.2.10/255.255.255.252
MAC = 00:ff:38:90:47:6b
GATEWAY =
DHCP SERV = 10.20.2.9
DHCP LEASE OBTAINED = Mon May 21 09:34:12 2007
DHCP LEASE EXPIRES = Tue May 20 09:34:12 2008
Realtek RTL8139 Family PCI Fast Ethernet NIC - Virtual Machine Network Services Driver
Index = 65540
GUID = {091D56D5-0FAF-44D3-917A-CA2971FAD5EF}
IP = 10.10.100.19/255.255.0.0
MAC = 00:13:d4:62:34:f8
GATEWAY = 10.10.30.31/0.0.0.0
DHCP SERV = 10.10.10.11
DHCP LEASE OBTAINED = Mon May 21 07:45:04 2007
DHCP LEASE EXPIRES = Tue May 22 07:45:04 2007
PRI WINS = 10.10.10.11/0.0.0.0
SEC WINS = 10.10.10.1/0.0.0.0
Mon May 21 09:34:14 2007 us=197036 Initialization Sequence Completed
" -
Hi all,
Just wanna update with the current issue…I'm currently running 1.2-BETA-1 version...
I just get the solution for this problem...I change the user configuration from "route-delay 2" to "route-delay 10" and the OpenVPN can successfully accessing OpenVPN Server and also can ping the LAN.
float
port 81
dev-node vpn
proto udp
remote 10.10.100.223 81
ping 30
persist-tun
persist-key
tls-client
ca ca.crt
cert 21.crt
key 21.key
ns-cert-type server
cipher BF-CBC
route-method exe
route-delay 10
pull
verb 4Any info regarding this issue why some client can connect successfully without any problem and some clients need to change the configuration as above. Need feedback from the expertise..
Thanks…