Problem with atheros 5212 pci wireless chip on wrap board
-
Dear all
Below I attached the hole dmesg. Is there a hardware compatibility problem with this chipset?
Copyright
1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.1-RELEASE-p10 #0: Sun Oct 29 01:44:26 UTC 2006
sullrich@builder.livebsd.com:/usr/obj.pfSense/usr/src/sys/pfSense_wrap.6
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by National Semi (233.31-MHz 586-class CPU)
Origin = "Geode by NSC" Id = 0x540 Stepping = 0
Features=0x808131 <fpu,tsc,msr,cx8,cmov,mmx>real memory = 134217728 (128 MB)
avail memory = 121917440 (116 MB)
wlan: mac acl policy registered
ath_hal: 0.9.16.16 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
cpu0 on motherboard
pcib0: <host to="" pci="" bridge="">pcibus 0 on motherboard
pci0: <pci bus="">on pcib0
ath0: <atheros 5212="">mem 0x80000000-0x8000ffff irq 12 at device 13.0 on pci0
ath0: unable to attach hardware; HAL status 14
device_attach: ath0 attach returned 6
sis0: <natsemi 10="" dp8381[56]="" 100basetx="">port 0x1000-0x10ff mem 0x81040000-0x81040fff irq 10 at device 14.0 on p0
sis0: Silicon Revision: DP83816A
miibus0: <mii bus="">on sis0
ukphy0: <generic ieee="" 802.3u="" media="" interface="">on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:0d:b9:00:d7:e0
sis1: <natsemi 10="" dp8381[56]="" 100basetx="">port 0x1400-0x14ff mem 0x81080000-0x81080fff irq 9 at device 15.0 on pc0
sis1: Silicon Revision: DP83816A
miibus1: <mii bus="">on sis1
ukphy1: <generic ieee="" 802.3u="" media="" interface="">on miibus1
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis1: Ethernet address: 00:0d:b9:00:d7:e1
sis2: <natsemi 10="" dp8381[56]="" 100basetx="">port 0x1800-0x18ff mem 0x810c0000-0x810c0fff irq 11 at device 16.0 on p0
sis2: Silicon Revision: DP83816A
miibus2: <mii bus="">on sis2
ukphy2: <generic ieee="" 802.3u="" media="" interface="">on miibus2
ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis2: Ethernet address: 00:0d:b9:00:d7:e2
Geode GPIO@ = f400
Geode PC Engines WRAP.1C/1D/1E v1.tinyBIOS V1.4a (C)1997-2005
isab0: <pci-isa bridge="">port 0xf400-0xf43f,0xf600-0xf63f at device 18.0 on pci0
isa0: <isa bus="">on isab0
pci0: <bridge>at device 18.1 (no driver attached)
atapci0: <national geode="" sc1100="" ata33="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at dev0
ata0: <ata 0="" channel="">on atapci0
ata1: <ata 1="" channel="">on atapci0
pci0: <multimedia, audio="">at device 18.3 (no driver attached)
Geode CBA@ 0x9000
Geode rev: 06 03
Timecounter "Geode" frequency 27000000 Hz quality 1000
pci0: <bridge>at device 18.5 (no driver attached)
orm0: <isa option="" rom="">at iomem 0xe0000-0xe7fff on isa0
ppc0: parallel port not found.
sio0 at port 0x3f8-0x3ff irq 4 flags 0x30 on isa0
sio0: type 16550A, console
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
RTC BIOS diagnostic error 80 <clock_battery>Timecounters tick every 10.000 msec
Fast IPsec: Initialized Security Association Processing.
ad0: 977MB <sandisk sdcfh-1024="" hdx="" 4.04="">at ata0-master PIO4
GEOM_LABEL: Label for provider ad0a is ufs/pfSense.
GEOM_LABEL: Label for provider ad0d is ufs/pfSenseCfg.
Trying to mount root from ufs:/dev/ufs/pfSense
WARNING: / was not properly dismounted
WARNING: /cf was not properly dismounted
WARNING: R/W mount of / denied. Filesystem is not clean - run fsck
WARNING: R/W mount of /cf denied. Filesystem is not clean - run fsck
sis0: link state changed to UP
sis1: link state changed to DOWN
sis2: link state changed to DOWN
pflog0: promiscuous mode enabledThanks in advance for any help
Regards,
Chris</sandisk></clock_battery></isa></bridge></multimedia,></ata></ata></national></bridge></isa></pci-isa></generic></mii></natsemi></generic></mii></natsemi></generic></mii></natsemi></atheros></pci></host></fpu,tsc,msr,cx8,cmov,mmx> -
Upgrade your BIOS.
-
I've downloaded the new version of tinybios from this page:
http://www.pcengines.ch/tinybios.htm
, but sadly I've no bloody idea how to upgrade the bios….! Is there anyone who can give me a simple and short howto? -
Download this file and check the readme, i prefer the "XModem" Update :
http://www.pcengines.ch/wbios111.zip
Flash upgrade:
There are two ways to upgrade the flash BIOS:
- SETBIOS.COM
This program can be executed from a DOS bootable disk. It will
look for WRAP.ROM, and program it into flash.- Xmodem update
Using a terminal program, press S during the memory test.
The setup screen will be displayed. Press X, then start a
X-Modem (1K, CRC) upload of e.g. WRAP1.UPD. The .UPD files
consist of the flash update WRAP_UP.BIN, and the flash image.
When the upload completes, the flash update is automatically
executed. -
Okay, I updated the bios but still have the same issue…..
here is the output from the dmesg:
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE-p4 #0: Mon Apr 30 11:13:54 EDT 2007
sullrich@builder6.pfsense.com:/usr/obj.pfSense/usr/src/sys/pfSense_wrap.6
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by National Semi (233.31-MHz 586-class CPU)
Origin = "Geode by NSC" Id = 0x540 Stepping = 0
Features=0x808131 <fpu,tsc,msr,cx8,cmov,mmx>real memory = 134217728 (128 MB)
avail memory = 121876480 (116 MB)
wlan: mac acl policy registered
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
cpu0 on motherboard
pcib0: <host to="" pci="" bridge="">pcibus 0 on motherboard
pci0: <pci bus="">on pcib0
ath0: <atheros 5212="">mem 0x80000000-0x8000ffff irq 12 at device 13.0 on pci0
ath0: unable to attach hardware; HAL status 14
device_attach: ath0 attach returned 6
sis0: <natsemi 10="" dp8381[56]="" 100basetx="">port 0x1000-0x10ff mem 0x81040000-0x81040fff irq 10 at device 14.0 on pci0
sis0: Silicon Revision: DP83816A
miibus0: <mii bus="">on sis0
ukphy0: <generic ieee="" 802.3u="" media="" interface="">on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:0d:b9:00:d7:e0
sis1: <natsemi 10="" dp8381[56]="" 100basetx="">port 0x1400-0x14ff mem 0x81080000-0x81080fff irq 9 at device 15.0 on pci0
sis1: Silicon Revision: DP83816A
miibus1: <mii bus="">on sis1
ukphy1: <generic ieee="" 802.3u="" media="" interface="">on miibus1
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis1: Ethernet address: 00:0d:b9:00:d7:e1
sis2: <natsemi 10="" dp8381[56]="" 100basetx="">port 0x1800-0x18ff mem 0x810c0000-0x810c0fff irq 11 at device 16.0 on pci0
sis2: Silicon Revision: DP83816A
miibus2: <mii bus="">on sis2
ukphy2: <generic ieee="" 802.3u="" media="" interface="">on miibus2
ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis2: Ethernet address: 00:0d:b9:00:d7:e2
Geode GPIO@ = f400
Geode PC Engines WRAP.1C/1D/1E v1.tinyBIOS V1.4a (C)1997-2005
isab0: <pci-isa bridge="">port 0xf400-0xf43f,0xf600-0xf63f at device 18.0 on pci0
isa0: <isa bus="">on isab0
pci0: <bridge>at device 18.1 (no driver attached)
atapci0: <national geode="" sc1100="" ata33="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 18.2 on pci0
ata0: <ata 0="" channel="">on atapci0
ata1: <ata 1="" channel="">on atapci0
pci0: <multimedia, audio="">at device 18.3 (no driver attached)
Geode CBA@ 0x9000
Geode rev: 06 03
Timecounter "Geode" frequency 27000000 Hz quality 1000
pci0: <bridge>at device 18.5 (no driver attached)
orm0: <isa option="" rom="">at iomem 0xe0000-0xe7fff on isa0
ppc0: parallel port not found.
sio0 at port 0x3f8-0x3ff irq 4 flags 0x30 on isa0
sio0: type 16550A, console
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
RTC BIOS diagnostic error 80 <clock_battery>Timecounters tick every 10.000 msec
Fast IPsec: Initialized Security Association Processing.
ad0: 977MB <sandisk sdcfh-1024="" hdx="" 4.04="">at ata0-master PIO4
GEOM_LABEL: Label for provider ad0a is ufs/pfSense.
GEOM_LABEL: Label for provider ad0d is ufs/pfSenseCfg.
Trying to mount root from ufs:/dev/ufs/pfSense
sis0: link state changed to UP
sis1: link state changed to DOWN
sis2: link state changed to DOWN
pflog0: promiscuous mode enabled</sandisk></clock_battery></isa></bridge></multimedia,></ata></ata></national></bridge></isa></pci-isa></generic></mii></natsemi></generic></mii></natsemi></generic></mii></natsemi></atheros></pci></host></fpu,tsc,msr,cx8,cmov,mmx> -
Wich version of PFsense do you use ?
My WRAP works fine with the 1.0.1 Release…