Setting up a VLAN part 2
-
VLAN1 is probably going to stop working here because hopefully you will stop sending any untagged packets to the switch from pfSense.
Configure the switch:
port: 1 2 3 4 5 6 7 8 vlan1: U U U U U U E E vlan100: T E E E E E U U
Unassign re1 from LAN to stop is sending untagged packets. This will lock you out of the pfSense box if you haven't got access from re2.
Steve
-
VLAN1 is probably going to stop working here because hopefully you will stop sending any untagged packets to the switch from pfSense.
Configure the switch:
port: 1 2 3 4 5 6 7 8 vlan1: U U U U U U E E vlan100: T E E E E E U U
Unassign re1 from LAN to stop is sending untagged packets. This will lock you out of the pfSense box if you haven't got access from re2.
Steve
vlan 1 is going to stop working? what does that mean? i would still like all 192. computers to work.
by tagging port 1 in vlan100 is that what 'unassing re1 from LAN to stop sending untagged packets' is?
i will wait for a reply before i set it up that way.
-
create a new vlan say 10 or something else than 1 or 100
Use only your current lan interface as management interface and both two vlan's to the same nic where you have vlan currently.
so your network would be
nic(lan): 192.168.1.1 /24 for management, you could also use something else subnet area
vlan10 (on another nic): this would be your current lan, so whatever you like to use, but notice, that this vlan and above management subnet wouldn't work if they have same subnets
vlan100 (on same nic as vlan10): this would be same as currentlythen add current configs to switch
vlan10: T U U U U U E E
vlan100: T E E E E E U U
remember to connect port 1 to pfsense -
create a new vlan say 10 or something else than 1 or 100
Use only your current lan interface as management interface and both two vlan's to the same nic where you have vlan currently.
so your network would be
nic(lan): 192.168.1.1 /24 for management, you could also use something else subnet area
vlan10 (on another nic): this would be your current lan, so whatever you like to use, but notice, that this vlan and above management subnet wouldn't work if they have same subnets
vlan100 (on same nic as vlan10): this would be same as currentlythen add current configs to switch
vlan10: T U U U U U E E
vlan100: T E E E E E U U
remember to connect port 1 to pfsenseok, what does vlan1 look like in the hp switch?
i think you just confused me more.
-
in this topology it doesn't exist
It is only "console" access to the firewall -
in this topology it doesn't exist
It is only "console" access to the firewalllet me rephrase.
that is ok if it is there and i dont use it, but i will have it in my switch. after reading the post, it seems as if my switch needs to look like this
vlan1
vlan10
vlan100maybe we should start with pfsense, do i have that configured properly?
re0- WAN
re1- vlan100 (10.10.10.1) dhcp enabled
re2- LAN (192.168.1.1) dhcp enabled–------------------
pfsense LAN goes into HP port 1 (vlan?) 192.168.1.x
pfsense vlan100 goes into HP port 7 (vlan100 on hp switch) 10.10.10.x and port 8 needs to be on vlan100 as well.
EDIT-
does the pfsense NIC even need to be a VLAN? if i am using a seperate NIC, shouldnt i be able to assign it to 10.10.10.x and deal with VLANs in the HP switch to segregate 10 traffic vs 192 traffic?
-
did you guys give up on me?
;D
-
Sorry I was out on an all night 120 mile cycle ride Saturday night. Yesterday was pretty much a write off! :)
I think we could easily loose sight of the big picture here.
The aim of this exercise is to learn about VLANs. The configuration we are hoping to end up with is:
pfSense using two interfaces, WAN on re0 and VLANs on re1.
The HP switch configured to split the VLANs between some it's ports. Such that some ports are pfSenses LAN interface and some are pfSenses other interface.Although you have LAN setup on re2 at the moment that's only temporary while we configure VLANs on re1.
Setup another VLAN as Metu69salemi suggested.
You should only have one cable between pfSense (re1) and the trunk port on the switch (port1).
Steve
-
Sorry I was out on an all night 120 mile cycle ride Saturday night. Yesterday was pretty much a write off! :)
I think we could easily loose sight of the big picture here.
The aim of this exercise is to learn about VLANs. The configuration we are hoping to end up with is:
pfSense using two interfaces, WAN on re0 and VLANs on re1.
The HP switch configured to split the VLANs between some it's ports. Such that some ports are pfSenses LAN interface and some are pfSenses other interface.Although you have LAN setup on re2 at the moment that's only temporary while we configure VLANs on re1.
Setup another VLAN as Metu69salemi suggested.
You should only have one cable between pfSense (re1) and the trunk port on the switch (port1).
Steve
hmmm, now i am confused, it is official.
i thought that doing everything from one interface was part of the reason i wasnt able to verify if i had everythign configured properly?
wasnt the recommendation to use 3 NICS?
re0- WAN
re1- VLANs (originally not in play)
re2- LAN (for 192.168.1.x network)that would mean two connections from pfsense to my switch
re1- for VLANs (or 10.10.10.x network)
re0- for the regular 192.168.1.x networkunless i missed something, that is how i thought it was going to end up.
thanks.
(btw, i dont blame you for taking the day off, the weekends are there to enjoy and relax, sounds like you did both) :)
-
i have access to another switch i can use, but it isnt in the mix yet, just want some feedback…
it is an HP switch, but a little more advanced/better GUI than the one i am using.
in this switch, the vlan has 4 options:
no
tagged
untagged
forbidi assume forbid= exclude
or is it
no=exclude
part of the confusion is that:
-i have never had to use vlans, but i want to learn
-every piece of device i have logged into with vlan capabilities has a different 'look' to it. -
Please see attached file
you could also allow from the switch to use another management ip from another vlan or setup another management vlan
-
Please see attached file
you could also allow from the switch to use another management ip from another vlan or setup another management vlanwhat is console? 1 PC i have connected to pfsense just to login to it to make changes?
also, wiring it up isnt a problem.
if i wire it i need to be able to build out the vlans for it to function properly.
i need guidance on that portion. i guess i need to go to the HP forums and ask them what the proper way to tag/untag is? that is my issue here (i think pfsense is setup properly).
thanks.
-
Console means, that you sit next to that machine, but in this case it's only needed if you have locked you self out from another vlan
-
Console means, that you sit next to that machine, but in this case it's only needed if you have locked you self out from another vlan
the HP switch has a management port section where i can dedicate 1 of the ports as a managed port.
i dont think that will be an issue unless i screw up the tagging/untagging/exclude, which is where i am stuck.
-
@tomdlgns:
hmmm, now i am confused, it is official.
i thought that doing everything from one interface was part of the reason i wasnt able to verify if i had everythign configured properly?
wasnt the recommendation to use 3 NICS?
re0- WAN
re1- VLANs (originally not in play)
re2- LAN (for 192.168.1.x network)Originally you wanted to use just two interfaces on the pfSense machine so that is what we are attempting to achieve. We only recommended you setup re2 so that you didn't get locked out of pfSense if you configured VLANs incorrectly. You have assigned LAN to it but we didn't expect you to. It could be any OPT interface.
@tomdlgns:
that would mean two connections from pfsense to my switch
re1- for VLANs (or 10.10.10.x network)
re0- for the regular 192.168.1.x networkunless i missed something, that is how i thought it was going to end up.
Whilst you could have both interfaces connected to the switch it would be far more complex to setup and MUCH more likely to cause problems.
Technically you don't need use VLANs at all, you want two subnets and you have two interfaces.
Let me layout what I expect the final configuration to be.
WAN - re0
LAN - VLAN10 - re1 192.168.1.X
OPT1 - VLAN100 - re1 10.10.10.X
OPT2 - re2 192.168.2.XI hope that makes some sort of sense!
Steve
-
@tomdlgns:
hmmm, now i am confused, it is official.
i thought that doing everything from one interface was part of the reason i wasnt able to verify if i had everythign configured properly?
wasnt the recommendation to use 3 NICS?
re0- WAN
re1- VLANs (originally not in play)
re2- LAN (for 192.168.1.x network)Originally you wanted to use just two interfaces on the pfSense machine so that is what we are attempting to achieve. We only recommended you setup re2 so that you didn't get locked out of pfSense if you configured VLANs incorrectly. You have assigned LAN to it but we didn't expect you to. It could be any OPT interface.
@tomdlgns:
that would mean two connections from pfsense to my switch
re1- for VLANs (or 10.10.10.x network)
re0- for the regular 192.168.1.x networkunless i missed something, that is how i thought it was going to end up.
Whilst you could have both interfaces connected to the switch it would be far more complex to setup and MUCH more likely to cause problems.
Technically you don't need use VLANs at all, you want two subnets and you have two interfaces.
Let me layout what I expect the final configuration to be.
WAN - re0
LAN - VLAN10 - re1 192.168.1.X
OPT1 - VLAN100 - re1 10.10.10.X
OPT2 - re2 192.168.2.XI hope that makes some sort of sense!
Steve
this gets better and better
where is 192.168.2.x coming from? and now another NIC?
-i'd like to setup a VLAN so i can work/test with it
-i can easily setup a second NIC/subnet using another switch, but that wont incorporate a VLAN, so i dont want to go that route.what i planned on was this:
re0-WAN
re1- VLAN100 10.10.10.x
re2- my regular lan 192.168.1.xwhat i wanted to do was then use my hp switch to work with the pfsense box
ports 1-4 would run the 192.168.1.x network and ports 5-8 would be tagged ports on vlan 100. i assumed that doing it this way would allow anything plugged into ports 5-8 would work on the vlan100 network.
later on, if i introduced a second vlan, vlan200 i THOUGHT i would be able to untag ports 7.8 and tag those in vlan 200 to work on another subnet.
apparently i am wrong in how vlans work, but i thought that was the entire point of VLANS… separate networks on the same physical switch.
edit-
are you guys saying that i cant have anything on the default lan tagged with vlan 100 traffic?
do i need to do something like this
default vlan- EEEEEEEE (this would need a 'console PC' so i could login to pfsense on 192.168.1.1 and make changes)
vlan10- TTTTUUUU (ports 1-4 tagged for vlan10)
vlan100-UUUUTTTT (ports 5-8 tagged for vlan100)or am i still way off?
-
@tomdlgns:
this gets better and better
:D
@tomdlgns:
where is 192.168.2.x coming from? and now another NIC?
192.168.2.X is just a subnet I invented to be the extra interface used for admin access.
There are still only 3 NICs but there are two VLANs on re1.@tomdlgns:
-i'd like to setup a VLAN so i can work/test with it
what i planned on was this:re0-WAN
re1- VLAN100 10.10.10.x
re2- my regular lan 192.168.1.xOk, we can aim for this. This will use three NICs at the end where as originally you wanted to use just two.
@tomdlgns:
what i wanted to do was then use my hp switch to work with the pfsense box
ports 1-4 would run the 192.168.1.x network and ports 5-8 would be tagged ports on vlan 100. i assumed that doing it this way would allow anything plugged into ports 5-8 would work on the vlan100 network.
later on, if i introduced a second vlan, vlan200 i THOUGHT i would be able to untag ports 7.8 and tag those in vlan 200 to work on another subnet.
Yes that's what we will do except that you will need 2 of the ports on your switch to connect to the pfSense box so you will only have 6 left for connecting clients (or other switches).
@tomdlgns:
apparently i am wrong in how vlans work, but i thought that was the entire point of VLANS… separate networks on the same physical switch.
You are right, that's exactly what they're for.
Here is the switch config I would expect to work for your current setup:
port: 1 2 3 4 5 6 7 8 vlan1: E E E E U U U U vlan100: T U U U E E E E
In which port 1 is connected to re1 and port 8 is connected to re2.
This will give you 10.10.10.x on ports 2-4 and 192.168.1.X on ports 5-7.Are all your NICs identical?
Steve
-
@tomdlgns:
this gets better and better
:D
@tomdlgns:
where is 192.168.2.x coming from? and now another NIC?
192.168.2.X is just a subnet I invented to be the extra interface used for admin access.
There are still only 3 NICs but there are two VLANs on re1.@tomdlgns:
-i'd like to setup a VLAN so i can work/test with it
what i planned on was this:re0-WAN
re1- VLAN100 10.10.10.x
re2- my regular lan 192.168.1.xOk, we can aim for this. This will use three NICs at the end where as originally you wanted to use just two.
@tomdlgns:
what i wanted to do was then use my hp switch to work with the pfsense box
ports 1-4 would run the 192.168.1.x network and ports 5-8 would be tagged ports on vlan 100. i assumed that doing it this way would allow anything plugged into ports 5-8 would work on the vlan100 network.
later on, if i introduced a second vlan, vlan200 i THOUGHT i would be able to untag ports 7.8 and tag those in vlan 200 to work on another subnet.
Yes that's what we will do except that you will need 2 of the ports on your switch to connect to the pfSense box so you will only have 6 left for connecting clients (or other switches).
@tomdlgns:
apparently i am wrong in how vlans work, but i thought that was the entire point of VLANS… separate networks on the same physical switch.
You are right, that's exactly what they're for.
Here is the switch config I would expect to work for your current setup:
port: 1 2 3 4 5 6 7 8 vlan1: E E E E U U U U vlan100: T U U U E E E E
In which port 1 is connected to re1 and port 8 is connected to re2.
This will give you 10.10.10.x on ports 2-4 and 192.168.1.X on ports 5-7.Are all your NICs identical?
Steve
thanks steve. i didnt realize, until after i posted, that you were using the same nic for the other vlan, my bad on that.
i have 3 nics now and i wanted to only use 2 until it was brought up that carrying multiple vlan traffic over 1 wire/nic might not work if the nic isnt vlan compatible, that is when the second LAN NIC (3rd NIC if you count WAN) was introduced.
i realize i will only have 6 ports to use for devices, but what i was getting at was that 1-4 was for 1 subnet and 5-8 was for another subnet (or did i mess up again)? 1 and 5 would be used for the respective NICs on pfsense.
my main goal is to
-incorporate a vlan
-not lock myself out of anythingi want to keep my existing 192.168.1.x network as is (for the other devices on it) and i want to be able to manage pfsense from any 192.168.1.x computer
knowing all of that, do you still suggest i connect/configure my network with what your last posted stated?
i dont mind a little redesign, but i want to make sure we are talking about the same stuff when i begin to implement this
-
Yes try my last suggestion. It should work, then again I thought that before! ::)
Steve
-
Yes try my last suggestion. It should work, then again I thought that before! ::)
Steve
ok thanks, will try that
can you explain why only 1 port is Tagges on vlan100?
port: 1 2 3 4 5 6 7 8
vlan1: E E E E U U U U
vlan100: T U U U E E E Ewhy isnt vlan100: T T T T E E E E
i understand why vlan1 is E E E E (those ports are for vlan100) and U U U U on vlan100 are untagged packets for the 192.168.1.x network, correct?