EMP-8602 400mw 802.11a/g/b wireless mini-pci - driver

squarepusher

There's an utility called ar5k, people use it to change the regdomain and countrycode, but I have seen som sites where people use it to change the deviceid.
So do a search on google for ar5k.c and be aware that you might ruin your card.

pcatiprodotnet

I received another suggestion…

[this is also suggested by above by lsf, but I must have missed it;
I usually skip quoted/reply text because it's usually repeat info
from an earlier post in the same thread.]

"Its possible that the PCI reset timing is causing this issue.
…
Be aware that PC Engines recently released an update to the BIOS for
its WRAP boards. From the release notes:
- WRAP BIOS revision history:
- ; v1.11
- ; pd 051108 extend insufficient PCI reset pulse width - caused
- ; problems with Atheros single chip cards.
The 8602 cards are (indeed) based on a single-chip Atheros part. "

Will try flashing the WRAP BIOS monday and report...
Thanks,-pc

lsf

Heh, I already mentioned the wrap firmware issue in the 5th post in this thread.
http://forum.pfsense.org/index.php?topic=676.msg5200#msg5200

I hope you already did upgrade to the newest bios rev.

lsf

Any news ? was the wrap firmware the issue ?

pcatiprodotnet

I haven't yet been able to allocate a few free hours to discover how to flash the WRAP.
It may have to wait until next week. I ordered two new WRAP.2C units, hopefully with
the latest bios, and two new EMP-8602. They should be arriving soon; will post results.
Thank you,-pc

hoba

from http://pcengines.ch/wrap1c.pdf :

(9) 9600 baud 3 38400 baud
(C) CHS mode L LBA mode
(X) Xmodem upload (Q) Quit

[…]

XMODEM upload of new firmware (X). Start transmission when prompted. 128 byte and 1024
byte packet sizes can be accepted, CRC mode only. Checksum mode is not supported as it is
considered too risky for firmware upgrade.
The actual flash update algorithm is included in the uploaded file. Flash programming takes
about two seconds. If power fails during this time, the BIOS chip will need to be
reprogrammed through other means.

pcatiprodotnet

I upgraded to wrap bios 1.11: "PC Engines WRAP.2B/2C v1.11".
I purchased two additional EMP-8602 mini-pci cards that do Not have "ff" in the device id.

Using the latest pfSense versions 04-02-2006 and 04-03-2006, both
old and new cards are NOT detected.
However, after "downgrading" to pfSense 03-27-2006 they both ARE detected!

Here is the output from "pciconf -lv" and "dmesg" when using pfSense 04-02-2006:

pciconf -lv

hostb0@pci0:0:0: class=0x060000 card=0x00000000 chip=0x00011078 rev=0x00 hdr=0x00
class = bridge
subclass = HOST-PCI
none0@pci0:13:0: class=0x020000 card=0x2063168c chip=0x001b168c rev=0x01 hdr=0x00
class = network
subclass = ethernet
sis0@pci0:14:0: class=0x020000 card=0x0020100b chip=0x0020100b rev=0x00 hdr=0x00
class = network
subclass = ethernet
none1@pci0:17:0: class=0x020000 card=0x2063168c chip=0x001b168c rev=0x01 hdr=0x00
class = network
subclass = ethernet
isab0@pci0:18:0: class=0x060100 card=0x0500100b chip=0x0510100b rev=0x00 hdr=0x00
class = bridge
subclass = PCI-ISA
none2@pci0:18:1: class=0x068000 card=0x0501100b chip=0x0511100b rev=0x00 hdr=0x00
class = bridge
atapci0@pci0:18:2: class=0x010180 card=0x0502100b chip=0x0502100b rev=0x01 hdr=0x00
class = mass storage
subclass = ATA
none3@pci0:18:3: class=0x040100 card=0x0503100b chip=0x0503100b rev=0x00 hdr=0x00
class = multimedia
subclass = audio
none4@pci0:18:5: class=0x068000 card=0x0505100b chip=0x0515100b rev=0x00 hdr=0x00
class = bridge

dmesg

Copyright 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.0-RELEASE-p6 #0: Sun Apr 2 22:26:42 UTC 2006
sullrich@builder.livebsd.com:/usr/obj.pfSense/usr/src/sys/pfSense_wrap.6
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by National Semi (266.69-MHz 586-class CPU)
Origin = "Geode by NSC" Id = 0x540 Stepping = 0
Features=0x808131 <fpu,tsc,msr,cx8,cmov,mmx>real memory = 134217728 (128 MB)
avail memory = 121917440 (116 MB)
wlan: mac acl policy registered
ath_hal: 0.9.14.9 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413)
npx0: [FAST]
npx0: <math processor="">on motherboard</math>
npx0: INT 16 interface
cpu0 on motherboard
pcib0: <host to="" pci="" bridge="">pcibus 0 on motherboard
pci0: <pci bus="">on pcib0
pci0: <network, ethernet="">at device 13.0 (no driver attached)
sis0: <natsemi 10="" dp8381[56]="" 100basetx="">port 0x1000-0x10ff mem 0x80040000-0x80040fff irq 10 at device 14.0 on pci0
sis0: Silicon Revision: DP83816A
miibus0: <mii bus="">on sis0
ukphy0: <generic ieee="" 802.3u="" media="" interface="">on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:0d:b9:03:8c:c4
pci0: <network, ethernet="">at device 17.0 (no driver attached)
Geode GPIO@ = f400
Geode PC Engines WRAP.2B/2C v1.11 tinyBIOS V1.4a (C)1997-2005
isab0: <pci-isa bridge="">port 0xf400-0xf43f,0xf600-0xf63f at device 18.0 on pci0
isa0: <isa bus="">on isab0
pci0: <bridge>at device 18.1 (no driver attached)
atapci0: <national geode="" sc1100="" ata33="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 18.2 on pci0
ata0: <ata 0="" channel="">on atapci0
ata1: <ata 1="" channel="">on atapci0
pci0: <multimedia, audio="">at device 18.3 (no driver attached)
Geode CBA@ 0x9000
Geode rev: 06 03
Timecounter "Geode" frequency 27000000 Hz quality 1000
pci0: <bridge>at device 18.5 (no driver attached)
pmtimer0 on isa0
orm0: <isa option="" rom="">at iomem 0xe0000-0xe7fff on isa0
ppc0: parallel port not found.
sio0 at port 0x3f8-0x3ff irq 4 flags 0x30 on isa0
sio0: type 16550A, console
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
Timecounters tick every 10.000 msec
Fast IPsec: Initialized Security Association Processing.
ad0: FAILURE - SETFEATURES SET TRANSFER MODE status=51 <ready,dsc,error>error=4 <aborted>ad0: 122MB <hitachi xx.v.3.7.0.0="" rev="" 0.00="">at ata0-master BIOSPIO
GEOM_LABEL: Label for provider ad0a is ufs/pfSense.
GEOM_LABEL: Label for provider ad0d is ufs/pfSenseCfg.
Trying to mount root from ufs:/dev/ufs/pfSense
sis0: link state changed to DOWN
pflog0: promiscuous mode enabled

Thank you,
-Pete</hitachi></aborted></ready,dsc,error></isa></bridge></multimedia,></ata></ata></national></bridge></isa></pci-isa></network,></generic></mii></natsemi></network,></pci></host></fpu,tsc,msr,cx8,cmov,mmx>

pcatiprodotnet

fyi:
EMP-8602 is detected and functioning again in the 04-06-06 pfSense snapshot…
http://www.pfsense.com/~sullrich/RELENG_1_SNAPSHOT_04-06-2006/pfSense.img.gz

Thanks,
-Pete