No IP address displayed
-
Hi all,
No IP address displayed, only an arrow (->) after em0 on the same line.
(please refers to picture attached)Host - Ubuntu 12.04 64bit
VM - pfSense
Virtualizer - VirtualBoxeth0 connected to cable modem, interface pppoe. Host can connect Internet
Ran "sudo ifconfig" to find ethernet MAC address of network interface.
[check] Enable Network Adapter
Bridge Adapter
Name : eth0
-> Advanced
Promiscuous Mode: Deny
MAC Address (change it to the MAC found as described above)
[uncheck] Cable ModemPlease help. Thanks
Rgds
satimis
-
So where do you have the PPPoE session setup, in the host or pfSense? Hard to see how the host can connect top the internet if pfSense is running the PPPoE.
You have spoofed the MAC in pfSense or in VirtualBox? Which interface?What are the settings on the em0 interface in pfSense? What IP address do you expect it to be?
Steve
-
So where do you have the PPPoE session setup, in the host or pfSense? Hard to see how the host can connect top the internet if pfSense is running the PPPoE.
Hi,
PPPoE session is setup on Host. Before when I ran the connection of Host via -> Cable modem -> router
There was address displayedYou have spoofed the MAC in pfSense or in VirtualBox? Which interface?
in pfSense. Bridge Adapter/eth0
What are the settings on the em0 interface in pfSense?
Where can I find them?
What IP address do you expect it to be?
192.168.0.10/24
Thanks
Rgds
satimis -
So you've bridged the NIC in the host machine to the pfSense VM? And that's the same NIC that the host machine is running PPPoE over?
How is the pfSense VM supposed to get an IP address in that range? Static IP? Are you running DHCP somewhere?
Steve
-
So you've bridged the NIC in the host machine to the pfSense VM? And that's the same NIC that the host machine is running PPPoE over?
Not yet on Host
$ cat /etc/network/interfaces```
auto lo
iface lo inet loopbackauto eth0
auto dsl-provider
iface dsl-provider inet ppp
pre-up /sbin/ifconfig eth0 up # line maintained by pppoeconf
provider dsl-provideriface eth0 inet manual
> How is the pfSense VM supposed to get an IP address in that range? Static IP? Are you running DHCP somewhere? Static IP satimis
-
If the interface is set as static IP it should appear as:
WAN (wan) -> em0 -> v4: 192.168.0.10/24
Did you set it as such in the initial setup?
Steve
-
If the interface is set as static IP it should appear as:
WAN (wan) -> em0 -> v4: 192.168.0.10/24
Did you set it as such in the initial setup?
Sorry, I couldn't recall correctly.
When the connection on PC;
ISP -> Cable Modem -> Router -> PCWAN (wan) -> em0 -> v4/DHCP: 192.168.0.12/24
(pls see attached img)Now
ISP -> Cable Modem -> PC
No IP address displayedsatimis
-
Ah, so the WAN interface is set to DHCP not static. The router gives it an IP when it's connected. When it isn't there the pfSense VM must establish the PPPoE connection. It's going to be difficult to set that up without an internal interface of some sort. You could do by using the host machine and an additional virtual NIC. Alternatively you could use an addtional VM connected internally to pfSense.
Steve
-
Ah, so the WAN interface is set to DHCP not static. The router gives it an IP when it's connected. When it isn't there the pfSense VM must establish the PPPoE connection. It's going to be difficult to set that up without an internal interface of some sort. You could do by using the host machine and an additional virtual NIC.
I have 2 physical NIC installed
-> Network
Adapter 1
[check] Enable Network Adapter
Attached to: Bridge Adapter
Neme: eth0) (I'm only allowed selecting eth0 or eth1 here, unable creating a name)
Advanced
Adapter Type: Intel PRO/1000MT Desktop (8254OEM)
Promiscuous Mode: Allow All
MAC Address: xxxxxxxxx
[check] Cable Connected
[Port Forwarding] (greyout)Adapter 2
[check] Enable Network Adapter
Attached to: Internal Network
Neme: intnet
Advanced
Adapter Type: Intel PRO/1000MT Desktop (8254OEM)
Promiscuous Mode: Deny
MAC Address: xxxxxxxxx
[check] Cable Connected
[Port Forwarding] (greyout)Alternatively you could use an addtional VM connected internally to pfSense.
Please advise how to do it. Pointer would be appreciated.
Thanks
satimis
-
What is the setup you're hoping to achieve with this in the end?
The two NICs you listed above are they both real physical NICs? I'll assume they are.
So technically I believe you could use the one NIC to be both the LAN and carry the PPPoE session that is the WAN but it will be complex to set up and hugely open to error! ;)
The should also the able to use the host machine to connect configure pfSense. I'm unfamiliar with virtualbox so I'll just outline what you would do. Create a virtual NIC in VB and add it to the pfSense VM. In pfSense assign that as the LAN interface. Do whatever is required in VB to make that NIC accessible by the host box and configure the host to use it as its default connection. The host should then receive an IP address from pfSense and you'll be able to connect the the webgui and configure the PPPoE connection.
An alternative would be to add an additional VM, anything with a web browser. Then add a virtual switch in VB and add virtual NICs to connect the new VM to it as well is the pfSense VM. In pfSense add the new NIC as LAN. Now the new VM should receive an IP from pfSense in the default range. Open the VM and open a browser, go to the webgui at 192.168.1.1 and configure pfSense. Setup the PPPoE connection.
Steve
-
What is the setup you're hoping to achieve with this in the end?
Hi,
My goal is to run pfSense as router (virtual) without the physical router. I don't expect touching the Host, keeping it clean. I have only 2 PCs, each with VirtualBox installed having 10 VMs running on each of them. The network will be as follow:-
ISP -> Cable Modem -> eth0 of PC-1
eth1 of PC-1 -> eth0 of PC-2 (only one physical NIC on PC-2)
All VMs on both PC use the Virtual router for routing
The two NICs you listed above are they both real physical NICs? I'll assume they are.
Yes. 2 physical NICs.
Open the VM and open a browser, go to the webgui at 192.168.1.1 and configure pfSense. Setup the PPPoE connection.
I couldn't browse the webgui of pfSense on Host browser nor on another VM browser.. This is very strange to me. I have installed another pfSense by importing pfSense.ova download. Please see my new posting re "Unable to browse pfSense". pfSense.ova was download on;
http://files.nyi.pfsense.org/mirror/downloads/old/Now I have another image "pfSense-2.0.3-RELEASE-4g-amd64-nanobsd.img.gz" download. I'll install another pfSense to check what will happen..
satimis
-
This is probably now a Virtual Box config problem. I'm no VB expert but please post some network config for your VMs. I'm not sure how that will work since a quick google seems to show that VirtualBox doesn't have a convenient network map.
Steve
-
This is probably now a Virtual Box config problem. I'm no VB expert but please post some network config for your VMs. I'm not sure how that will work since a quick google seems to show that VirtualBox doesn't have a convenient network map.
$ cat /etc/network/interfaces```
auto lo
iface lo inet loopbackVM1 and VM2 the same. Host: $ cat /etc/network/interfaces``` auto lo iface lo inet loopback auto eth0 auto dsl-provider iface dsl-provider inet ppp pre-up /sbin/ifconfig eth0 up # line maintained by pppoeconf provider dsl-provider iface eth0 inet manual
satimis
-
What are VM1 and VM2?
Th host configuration is not important either. We need to see how VirtualBox's internal virtual network is configured. For example see the attached screenshot that I've shamelessly borrowed from Jonpoz. That's how ESXi shows it's network config.Steve
-
What are VM1 and VM2?
VM1 - Ubuntu 12.04 desktop
VM2 - LinuxMint desktopTh host configuration is not important either. We need to see how VirtualBox's internal virtual network is configured. For example see the attached screenshot that I've shamelessly borrowed from Jonpoz. That's how ESXi shows it's network config.
How to find it? Thanks
satimis
-
Hmm, Ok some reading later. It appears, and correct me if I'm wrong here, that there is no real concept of a switch in Virtual Box at least not by default. You can add various things like openvswitch to do it but it's not standard. There's also no easy way to view the whole network config as there is in ESXi so we have to go through it step by step. There are at least two internal networks that can be used to separate VMs and we can use for pfSense. There are also a ton of tutorials out there like this one: http://pc-addicts.com/how-to-install-pfsense-in-virtualbox/
Edit: Just watch that linked video. In fact you have as many independent internal networks as you want, the switches are implied.
So the pfSense VM should have two network adapters enabled. The first should be a bridge adapter, that will be the pfSense WAN. The second should be an internal adapter, that will be the pfSense LAN.
The VM you are suing to configure pfSense should have one network adapter and it should be the internal type.
The internal adapters of both VMs MUST have the same name otherwise they will be isolated.I'm unsure about adding an adapter to allow the host to access the internet through pfSense though. :-\
Steve
-
Hmm, Ok some reading later. It appears, and correct me if I'm wrong here, that there is no real concept of a switch in Virtual Box at least not by default. You can add various things like openvswitch to do it but it's not standard. There's also no easy way to view the whole network config as there is in ESXi so we have to go through it step by step. There are at least two internal networks that can be used to separate VMs and we can use for pfSense. There are also a ton of tutorials out there like this one: http://pc-addicts.com/how-to-install-pfsense-in-virtualbox/
- snip-
Thanks for your link.
I have no problem to install pfSense but unable making it to work. I have tried importing .ova and .vdi download on Internet. pfSense can start without probem. But I couldn't browse it on VM and Host.
em0 -> (not pointing to device/IP address)
(see image attached)It can't connect ISP even after filling in the MAC address.
I watched following video;
Setup Virtual Lab | Networking and Virtualbox
http://www.youtube.com/watch?v=3W9QTm-l1ckThe physical setup is behind a physical router
ISP (pppoe/ethernet) -> Router -> PCWhat I expect to achieve is without a physical route. If it is a MUST behind a physical router that is NOT what I expect to do.
satimis
-
Hi stephenw10,
Further to my late posting I found following article:
Virtualize your router using pfSense and Virtualbox
http://www.area536.com/projects/virtualize-your-router-using-pfsense-and-virtualbox/It seems to me possible to replace the physical router with pfSense as virtual router.
I made another round download pfSense-2.0.3-RELEASE-amd64.ova and import it to VirtualBox. Thereafter started it without problem. Both em0 and em1 are connected.
(see attached image)Adapter-1
Bridge Adapter
eth0Adapter-2
Bridge Adapter
eth1WAN (wan) -> em1 -> 192.168.0.11 (DHCP)
LAN (lan) -> em0 -> 192.168.1.1But still I couldn't browse it on Host browser running;
http://192.168.1.1
or
https://192.168.1.1It is quite strange to me.
satimis
-
You will have to browse to the pfSense webgui from the internal VM and make sure they both connected to the same internal network name.
What OS are you using for the other VM? Does it receive an IP from the pfSense DHCP server?Steve
-
You will have to browse to the pfSense webgui from the internal VM and make sure they both connected to the same internal network name.
I got it, thanks
VM - Ubuntu 12.04 desktop 64bit
On browser ran;
192.168.1.1-> Add Exception
Get Certificate
[check] Permanently store this exception
-> Confirm Security ExceptionPls see attached images.
Adapter-1 same as pfSense
Adapter-2 same as pfSenseWhat will be the login and password ?
Where can I find tutorial using the webgui pfSense to configure ?
$ cat /etc/network/interfaces```
auto lo
iface lo inet loopbacksudo ifconfig
eth0 Link encap:Ethernet HWaddr 08:00:27:10:8c:3d
inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::a00:27ff:fe10:8c3d/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4549 errors:0 dropped:0 overruns:0 frame:0
TX packets:3824 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:4787482 (4.7 MB) TX bytes:630362 (630.3 KB)eth1 Link encap:Ethernet HWaddr 08:00:27:e6:ca:14
inet addr:192.168.1.100 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::a00:27ff:fee6:ca14/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:267 errors:0 dropped:0 overruns:0 frame:0
TX packets:268 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:176246 (176.2 KB) TX bytes:37546 (37.5 KB)lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:254 errors:0 dropped:0 overruns:0 frame:0
TX packets:254 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:44773 (44.7 KB) TX bytes:44773 (44.7 KB)I don't think Ubuntu 12.04 receive IP from pfSense routing? On Host $ sudo ifconfig``` eth0 Link encap:Ethernet HWaddr 00:26:18:44:b6:1a inet addr:192.168.0.10 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::226:18ff:fe44:b61a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14177 errors:0 dropped:0 overruns:0 frame:0 TX packets:12287 errors:0 dropped:0 overruns:0 carrier:4 collisions:0 txqueuelen:1000 RX bytes:15365450 (14.6 MiB) TX bytes:1973191 (1.8 MiB) Interrupt:18 eth1 Link encap:Ethernet HWaddr 90:f6:52:03:57:86 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B)
What OS are you using for the other VM?
I have Ubuntu/LinuxMint/OpenSUSE running here.
Does it receive an IP from the pfSense DHCP server?
I don't think so. It receive IP from the physical router
Connection;
ISP -> Cable Modem -> Router -> PC eth0 (built-in NIC of motherboard)After making sure it works I'll change back to;
ISP -> Cable Modem -> PC eth0 (built-in NIC of motherboard)