CHAP Method For Radius

[alexus]

I just found out that captice portal doesnt suuport CHAP method for Radius identification!
That is kind of bad sinci it is required by most radius servers, including feree radius, also running plaine EAP w/o MD5 is completely stupid.

Will the CHAP suport be added?

[hoba]

the captive portal is a 100% clone of m0n0 atm, at least when it comes to pfSense 1.0 release and there won't be any changes concerning this for 1.0 and it's too early to discuss 1.1 at this point.

[jeroen234]

chap2 is suported
if have it with pfsense beta2 and freeradius

[alexus]

jeroen234, I have Beta2 but I dont see the option anywhere to enable CHAP2 besides what do yoo mean MS CHAP v2? (Because I never herad of regular CHAP v2)

hoba, thne what protocol is used in the Monowal?

[jeroen234]

you enable the chap  protocol in youre radius server
by making the passwords in the  chap v1/v2 protocol way

freeradius has this standaard

pfsense + freeradius package is also using the chap v1/v2 format when using the pfsense freeradius userbase

[alexus]

so in freeradius config I have to chane
CHAP{
authentication = chap2
}

or what?

[jeroen234]

# under MODULES, make sure mschap is uncommented!
    mschap {
      # authtype value, if present, will be used
      # to overwrite (or add) Auth-Type during
      # authorization. Normally, should be MS-CHAP
      authtype = MS-CHAP

# if use_mppe is not set to no, mschap will
      # add MS-CHAP-MPPE-Keys for MS-CHAPv1 and
      # MS-MPPE-Recv-Key/MS-MPPE-Send-Key for MS-CHAPv2
      #
      use_mppe = yes

# if mppe is enabled, require_encryption makes
      # encryption moderate
      #
      require_encryption = yes

# require_strong always requires 128 bit key
      # encryption
      #
      require_strong = yes

authtype = MS-CHAP
      # The module can perform authentication itself, OR
      # use a Windows Domain Controller. See the radius.conf file
      # for how to do this.
    }

authorize {
        preprocess
        mschap
suffix
eap
files
    }

authenticate {

#
        #  MSCHAP authentication.   
        Auth-Type MS-CHAP {
              mschap
          }

#  Allow EAP authentication.
        eap
    }

[alexus]

oh ok, so its MS CHAP afterall, let me try that

Thanks!

[jeroen234]

in youre users file you have this to use chap v1 on windows 95/98 or chap v2 on higher windows versions

"testuser"      User-Password == "Secret149"

when you crypt youre passwordts the chap protocol will fail

[alexus]

Ive edited the config withe the settings you provided, but it still says that username is invalis, aslo for some reason the captive portal doesnt send Auth-Type = MS-CHAP… ?

[jeroen234]

all captive portals send auth type = local
this is normal
check the bigining of youre users file angainst myne
i think i have atherd there a thing to make vpn and portal working on pfsense

i  think it was somfing with system

# DEFAULT entries match with all login names.
# Note that DEFAULT entries can also Fall-Through (see first entry).
# A name-value pair from a DEFAULT entry will _NEVER_ override
# an already existing name-value pair.
#

#
# First setup all accounts to be checked against the UNIX /etc/passwd.
# (Unless a password was already given earlier in this file).
#
#DEFAULT	Auth-Type = System
#	Fall-Through = 1

#
# Set up different IP address pools for the terminal servers.
# Note that the "+" behind the IP address means that this is the "base"
# IP address. The Port-Id (S0, S1 etc) will be added to it.
#
#DEFAULT	Service-Type == Framed-User, Huntgroup-Name == "alphen"
#		Framed-IP-Address = 192.168.1.32+,
#		Fall-Through = Yes

#DEFAULT	Service-Type == Framed-User, Huntgroup-Name == "delft"
#		Framed-IP-Address = 192.168.2.32+,
#		Fall-Through = Yes

#
# Defaults for all framed connections.
#
DEFAULT	Service-Type == Framed-User
	Framed-IP-Address = 255.255.255.254,
	Framed-MTU = 576,
	Service-Type = Framed-User,
	Fall-Through = Yes

#
# Default for PPP: dynamic IP address, PPP mode, VJ-compression.
# NOTE: we do not use Hint = "PPP", since PPP might also be auto-detected
#	by the terminal server in which case there may not be a "P" suffix.
#	The terminal server sends "Framed-Protocol = PPP" for auto PPP.
#
DEFAULT	Framed-Protocol == PPP
	Framed-Protocol = PPP,
	Framed-Compression = Van-Jacobson-TCP-IP

#

[alexus]

I just looked through the USERS file and it looks exactly the same as yours. I dont know what to do…

[jeroen234]

oke so system passwords are disabled that is good

start freeradius with
radiusd -x
or with freeradius -x
then try loggin in trouw the portal and look at the error that freeradius is giving in its screen

[alexus]

yea I am ruuning in the debug mode, and there are no errors, and at the end it says, password is invalid… and it sends Access-Reject
I'm lost now...  is there a soft client that send MS-CHAP Access Requests?

[alexus]

just spoke with people from Mono they say it uses PAP…
hoba, do you know what version of Mono are u using? 1.20 or 1.21?

[sullrich]

1.21

[aldo]

it does use pap only.

just add authtpe=pap

in your radius configuration should work depending on your backend it is really no worse than chap.
if you are paranoid and an stunnel from you NAS to your radius backend

[alexus]

actually I had to use Auth-Type== local, instead of system which is defult… in that case it will fall through all local modules installed