Pdsbm-ln2 1U server Lan Ports fail in RC canidate. Using Intel 82573 nic
-
I have updated and reset the bios from 2007 version to a 2010 version. There is no PCI cards in the system when I test the two on board network ports. When those are enabled with jumpers nothing in PCI slots work. Not wifi card or the dual nic I have. But disable the 2 on board and then I can use PCI slots. Funny thing is that the two on board are newer chips but still using same driver as the dual nic I have and the dual nic will work fine if both on board are turned off.
-
I would even buy gold support from PFSense if someone gets this working for me.
-
Did you try booting in verbose mode to get more info?
I'm guessing this is caused by something which is actually better supported in FreeBSD 10 than it was in 8.3. Some feature, possible something ACPI, is being seen and causing some problem which was previously ignored. You say it didn't boot at all when ACPI was disabled completely. You might try booting with various ACPI disabled instead.
Searching for 'Setup of Shared code failed' is not very helpful, there seem to be many different errors that result in this.
pcib1: failed to allocate initial I/O port window: 0-0xfff pcib1: failed to allocate initial memory window: 0-0xfffff pcib1: failed to allocate initial prefetch window: 0-0xfffff
This is obviously bad but it's not obvious quite how it relates to the issue. I would suggest that the BIOS is passing bad values for the PCI device setup which is why I suggested disabling ACPI.
Steve
-
Since you have the NICs that are specifically mentioned in the this bug list (old though), you should probably check the firmware:
@https://wiki.freebsd.org/BugBusting/Commonly_reported_issues:em(4) watchdog timeouts on Intel 82573 NICs
Reference: http://e1000.sourceforge.net/doku.php?id=known_issues#v_l_e_tx_unit_hang_messages
Fix: DOS-based EEPROM patcher from Intel
Fix: Boot Linux, install ethtool(8), and follow this procedure
Troubleshooting: when using em(4) driver 6.7.3 or later, you can dump the contents of the EEPROM by doing sysctl dev.em.X.debug=2 (0=em0, 1=em1, etc.). You'll see something like this from the kernel:
Interface EEPROM Dump:
Offset
0x0000 3000 8f48 d903 0d20 f746 0057 ffff ffff
0x0010 ffff ffff 026b 109a 15d9 109a 8086 80df
0x0020 0000 2000 7e54 0000 1000 00da 0004 2700
0x0030 6cc9 3150 0732 040b 2984 0000 c000 0706Since the above code prints things in little-endian-stored words, you need to look at the value at offset 0x1f (and not 0x1e like Linux ethtool!), which in the above example is value 0xdf. Bit 0 should be set (1), which disables the power-saving feature that causes the problem. In the above example, the bit is set, which means that the above NIC is not susceptible to the bug
Hmm, this doesn't work for me using a different em interface but the same driver. :-\
Edit: Hmm, not sure that debug level patch ever made it into the driver.
Steve
-
Ah, has just changed in more recent drivers. You have to run:
[2.2-RC][root@xtm5.localdomain]/root: sysctl dev.em.5.nvm=1 dev.em.5.nvm: -1 -> -1
Then check the output in dmesg (or the system log):
Interface EEPROM Dump: Offset 0x0000 9000 877f 7adc 0420 f746 1090 ffff ffff 0x0010 ffff ffff 026b 0000 8086 10d3 ffff 8758 0x0020 0000 2001 7e74 ffff 1000 00c8 0000 2704 0x0030 6cc9 3150 073e 460b 2d84 0140 f000 0706
My NIC has address 0x1f, bit 1 set to 0 but it's a different NIC so that's not relevant.
Steve
-
Also you might try the suggestion from https://www.freebsd.org/doc/handbook/acpi-overview.html for acpi related system hangs.
Add:hint.apic.0.disabled="1"
to /boot/loader.conf.local
See if that allows you to boot with the other Intel card in the box.Also you could try setting:
hw.acpi.host_mem_start="0xf0000000"
also in /boot/loader.conf.local
That might help with the pci brige allocation issues.Try those separately though.
Steve
-
Also you might try the suggestion from https://www.freebsd.org/doc/handbook/acpi-overview.html for acpi related system hangs.
Add:hint.apic.0.disabled="1"
to /boot/loader.conf.local
See if that allows you to boot with the other Intel card in the box.Also you could try setting:
hw.acpi.host_mem_start="0xf0000000"
also in /boot/loader.conf.local
That might help with the pci brige allocation issues.Try those separately though.
Steve
Well careful with the ACPI in loader.conf. I just had done that and system failed to boot like when I changed in bios. I had to reinstall it all. In doing that I ran out of time before work so the second part can not be done.
![2014-12-13 11.27.58.jpg](/public/imported_attachments/1/2014-12-13 11.27.58.jpg)
![2014-12-13 11.27.58.jpg_thumb](/public/imported_attachments/1/2014-12-13 11.27.58.jpg_thumb) -
Well careful with the ACPI in loader.conf.
Do you mean ACPI or APIC here? Did you try both?
Steve
-
hint.apic.0.disabled="1"
Is what I tried. Now I will try the second command you mentioned.. Hope that don't crash me and make me reinstall again..
But not sure why ACPI said it crashed when apic is the command I used. Intersting. Look at the picture..
-
hw.acpi.host_mem_start="0xf0000000" done in both loader.conf and loader.conf.local.. I had to create a new loader.conf.local non existed. But when I did in both the same lock up happened. I did not pull the pci Card out with 2 nics and just try the on board dual nic but I don't think any thing would be different
I really don't want to switch to another firewall..I really like pfsense.
-
Did you try booting verbose yet?
Did you dump the nic eprom?To avoid re-installing you can enter loader tunables by interrupting the boot loader and entering them manually. Of course they are then lost on the next boot.
Steve
-
Verbose mode no
debug mode noMy work schedule keeps me busy. I will have more time tomorrow as that is a day off for me. Then I will try those. Really not sure how to do the debug part yet
Also breaking the bootloader to put in variables? Can this be done with USB keyboard? I can't use the keyboard after bios till firewall almost booted.. it need PS2 keyboard to be able to use during the part of first loading and first menu of pfsense
AND if I but in debug mode do I want to turn on the internal nic's and pull the pci I am using now or how you want this test?
and will it keep the logs if you want the log of when it will crash. -
https://bugs.pcbsd.org/issues/4212
-
To dump the Intel eprom you just run the sysctl and then look in the logs like I showed above. To be honest I doubt that's your issue, the symptoms don't seem the same, but it's easy to do and if your NICs do have broken firmware that needs to be sorted.
If your BIOS is set to use a USB keyboard it should work.
Steve
-
Verbose on
rom commands done but not the 5 you had only 0 and 1 worked for me. with pci card. will try the onboard nextKeyboard is on in bios.. I can use keyboard in bios but after pfsense starts I can't use keyboard till it gets to more then half way through bootup then I get keyboard usage back again.
Table 'FACP' at 0xbf68ad08
Table 'TCPA' at 0xbf68ad8c
Table 'MCFG' at 0xbf68adbe
Table 'APIC' at 0xbf68adfa
APIC: Found table at 0xbf68adfa
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 0 ACPI ID 0: enabled
SMP: Added CPU 0 (AP)
MADT: Found CPU APIC ID 1 ACPI ID 1: enabled
SMP: Added CPU 1 (AP)
Copyright 1992-2014 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 10.1-RELEASE-p1 #0 fd28f0b(releng/10.1)-dirty: Sat Dec 13 14:00:20 CST 2014
root@pfsense-22-amd64-builder:/usr/obj.amd64/usr/pfSensesrc/src/sys/pfSense_SMP.10 amd64
FreeBSD clang version 3.4.1 (tags/RELEASE_34/dot1-final 208032) 20140512
Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff824c7000.
Calibrating TSC clock ... TSC clock: 2194542438 Hz
CPU: Intel(R) Pentium(R) Dual CPU E2200 @ 2.20GHz (2194.54-MHz K8-class CPU)
Origin = "GenuineIntel" Id = 0x6fd Family = 0x6 Model = 0xf Stepping = 13
Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0xe39d <sse3,dtes64,mon,ds_cpl,est,tm2,ssse3,cx16,xtpr,pdcm>AMD Features=0x20000800 <syscall,lm>AMD Features2=0x1 <lahf>TSC: P-state invariant, performance statistics
real memory = 4294967296 (4096 MB)
Physical memory chunk(s):
0x0000000000010000 - 0x0000000000099fff, 565248 bytes (138 pages)
0x0000000000100000 - 0x00000000001fffff, 1048576 bytes (256 pages)
0x00000000024f6000 - 0x00000000b73f0fff, 3035607040 bytes (741115 pages)
0x0000000100000000 - 0x000000013ffe7fff, 1073643520 bytes (262120 pages)
avail memory = 4088520704 (3899 MB)
Event timer "LAPIC" quality 400
ACPI APIC Table: <ptltd ="" apic ="">INTR: Adding local APIC 1 as a target
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
APIC: CPU 0 has ACPI ID 0
APIC: CPU 1 has ACPI ID 1
x86bios: IVT 0x000000-0x0004ff at 0xfffff80000000000
x86bios: SSEG 0x098000-0x098fff at 0xfffffe003f3a4000
x86bios: EBDA 0x09d000-0x09ffff at 0xfffff8000009d000
x86bios: ROM 0x0a0000-0x0fefff at 0xfffff800000a0000
XEN: CPU 0 has VCPU ID 0
XEN: CPU 1 has VCPU ID 1
ULE: setup cpu 0
ULE: setup cpu 1
ACPI: RSDP 0xf7260 00014 (v00 PTLTD )
ACPI: RSDT 0xbf683b6d 00060 (v01 PTLTD RSDT 06040000 LTP 00000000)
ACPI: FACP 0xbf68ad08 00084 (v01 SUPRMC 06040000 PTL 00000003)
ACPI: DSDT 0xbf68569f 05669 (v01 INTEL BR_WATER 06040000 MSFT 03000001)
ACPI: FACS 0xbf68bfc0 00040
ACPI: TCPA 0xbf68ad8c 00032 (v01 SMC 06040000 PTL 00000000)
ACPI: MCFG 0xbf68adbe 0003C (v01 PTLTD MCFG 06040000 LTP 00000000)
ACPI: APIC 0xbf68adfa 00068 (v01 PTLTD ? APIC 06040000 LTP 00000000)
ACPI: BOOT 0xbf68ae62 00028 (v01 PTLTD $SBFTBL$ 06040000 LTP 00000001)
ACPI: SLIC 0xbf68ae8a 00176 (v01 OEMID_ OEMTABLE 06040000 LTP 00000000)
ACPI: SSDT 0xbf685440 0025F (v01 PmRef Cpu0Tst 00003000 INTL 20050228)
ACPI: SSDT 0xbf68539a 000A6 (v01 PmRef Cpu7Tst 00003000 INTL 20050228)
ACPI: SSDT 0xbf6852f4 000A6 (v01 PmRef Cpu6Tst 00003000 INTL 20050228)
ACPI: SSDT 0xbf68524e 000A6 (v01 PmRef Cpu5Tst 00003000 INTL 20050228)
ACPI: SSDT 0xbf6851a8 000A6 (v01 PmRef Cpu4Tst 00003000 INTL 20050228)
ACPI: SSDT 0xbf685102 000A6 (v01 PmRef Cpu3Tst 00003000 INTL 20050228)
ACPI: SSDT 0xbf68505c 000A6 (v01 PmRef Cpu2Tst 00003000 INTL 20050228)
ACPI: SSDT 0xbf684fb6 000A6 (v01 PmRef Cpu1Tst 00003000 INTL 20050228)
ACPI: SSDT 0xbf683bcd 013E9 (v01 PmRef CpuPm 00003000 INTL 20050228)
MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000
ioapic0: Routing external 8259A's -> intpin 0
lapic0: Routing NMI -> LINT1
lapic0: LINT1 trigger: edge
lapic0: LINT1 polarity: high
lapic1: Routing NMI -> LINT1
lapic1: LINT1 trigger: edge
lapic1: LINT1 polarity: high
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0 <version 2.0="">irqs 0-23 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00000200 err: 0x000000f0 pmc: 0x00010400
firmware: 'iwn4965fw' version 0: 187972 bytes loaded at 0xffffffff81a1b80c
firmware: 'iwn5000fw' version 0: 340696 bytes loaded at 0xffffffff81a496fc
firmware: 'iwn5150fw' version 0: 337400 bytes loaded at 0xffffffff81a9ca84
firmware: 'iwn6000fw' version 0: 454608 bytes loaded at 0xffffffff81aef12c
firmware: 'wpifw' version 153229: 150100 bytes loaded at 0xffffffff81df6cc4
firmware: 'iwn6000g2afw' version 0: 444128 bytes loaded at 0xffffffff81b5e1ac
firmware: 'iwn6000g2bfw' version 0: 460912 bytes loaded at 0xffffffff81bca93c
firmware: 'iwn6050fw' version 0: 469780 bytes loaded at 0xffffffff81c3b25c
snd_unit_init() u=0x00ff8000 [512] d=0x00007c00 [32] c=0x000003ff [1024]
feeder_register: snd_unit=-1 snd_maxautovchans=16 latency=5 feeder_rate_min=1 feeder_rate_max=2016000 feeder_rate_round=25
firmware: 't4fw_cfg' version 0: 3059 bytes loaded at 0xffffffff8164c804
firmware: 't4fw_cfg_uwire' version 0: 21284 bytes loaded at 0xffffffff8164d3f7
firmware: 't4fw' version 0: 512512 bytes loaded at 0xffffffff8165271b
firmware: 't5fw_cfg' version 0: 3435 bytes loaded at 0xffffffff816cf9cc
firmware: 't5fw' version 0: 513024 bytes loaded at 0xffffffff816d0737
firmware: 'mw88W8363fw' version 0: 94940 bytes loaded at 0xffffffff81cb992c
firmware: 'mwlboot' version 0: 2280 bytes loaded at 0xffffffff81cd0c08
firmware: 'rsu-rtl8712fw' version 120: 122328 bytes loaded at 0xffffffff81dbaae4
firmware: 'runfw' version 0: 8192 bytes loaded at 0xffffffff81dd8ca4
firmware: 'rt2561fw' version 0: 8192 bytes loaded at 0xffffffff81d5aff4
wlan: mac acl policy registered
firmware: 'rt2561sfw' version 0: 8192 bytes loaded at 0xffffffff81d5d0a4
firmware: 'urtwn-rtl8188eufw' version 111: 13904 bytes loaded at 0xffffffff81ddb5dc
firmware: 'urtwn-rtl8192cfwT' version 111: 16076 bytes loaded at 0xffffffff81ddecdc
firmware: 'urtwn-rtl8192cfwU' version 111: 16076 bytes loaded at 0xffffffff81de2c54
firmware: 'rt2661fw' version 0: 8192 bytes loaded at 0xffffffff81d5f154
firmware: 'rt2860fw' version 0: 8192 bytes loaded at 0xffffffff81d61204
firmware: 'mxge_eth_z8e' version 377284: 120629 bytes loaded at 0xffffffff81cd16c0
wlan: <802.11 Link Layer>
firmware: 'mxge_ethp_z8e' version 387604: 121317 bytes loaded at 0xffffffff81ceeeb0
firmware: 'mxge_rss_eth_z8e' version 534724: 151912 bytes loaded at 0xffffffff81d0c950
firmware: 'mxge_rss_ethp_z8e' version 544468: 152837 bytes loaded at 0xffffffff81d31b70
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff80606640, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff806066f0, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff806067a0, 0) error 1
iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/.
iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_bss_fw, 0xffffffff8062de10, 0) error 1
iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/.
iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffffffff8062dec0, 0) error 1
iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/.
iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffffffff8062df70, 0) error 1
firmware: 'iwn1000fw' version 0: 337520 bytes loaded at 0xffffffff8187260c
firmware: 'iwn2000fw' version 0: 695876 bytes loaded at 0xffffffff818c4d2c
firmware: 'iwn2030fw' version 0: 707392 bytes loaded at 0xffffffff8196ec1c
Hardware, Intel Secure Key RNG: RDRAND is not present
Hardware, VIA Nehemiah Padlock RNG: VIA Padlock RNG not present
null: <null device,="" zero="" device="">Falling back to <software, yarrow="">random adaptor
random: <software, yarrow="">initialized
nfslock: pseudo-device
crypto: <crypto core="">VESA: INT 0x10 vector 0xc000:0x0014
VESA: information block
0000 56 45 53 41 00 03 00 01 00 99 01 00 00 00 40 00
0010 00 99 77 00 00 01 38 01 00 99 4a 01 00 99 73 01
0020 00 99 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0030 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0040 60 01 61 01 62 01 63 01 64 01 65 01 66 01 67 01
0050 68 01 3c 01 4d 01 5c 01 3a 01 4b 01 5a 01 07 01
0060 1a 01 1b 01 05 01 17 01 18 01 12 01 14 01 15 01
0070 01 01 03 01 11 01 ff ff 00 00 00 00 00 00 00 00
0080 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0090 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00a0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00c0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0100 49 6e 74 65 6c 28 72 29 42 72 6f 61 64 77 61 74
0110 65 72 2d 47 20 47 72 61 70 68 69 63 73 20 43 68
0120 69 70 20 41 63 63 65 6c 65 72 61 74 65 64 20 56
0130 47 41 20 42 49 4f 53 00 49 6e 74 65 6c 20 43 6f
0140 72 70 6f 72 61 74 69 6f 6e 00 49 6e 74 65 6c 28
0150 72 29 42 72 6f 61 64 77 61 74 65 72 2d 47 20 47
0160 72 61 70 68 69 63 73 20 43 6f 6e 74 72 6f 6c 6c
0170 65 72 00 48 61 72 64 77 61 72 65 20 56 65 72 73
0180 69 6f 6e 20 30 2e 30 00 00 00 00 00 00 00 00 00
0190 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01a0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01c0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
VESA: 17 mode(s) found
VESA: v3.0, 7616k memory, flags:0x1, mode table:0xfffffe003f3fa040 (99000040)
VESA: Intel(r)Broadwater-G Graphics Chip Accelerated VGA BIOS
VESA: Intel Corporation Intel(r)Broadwater-G Graphics Controller Hardware Version 0.0
io: VMBUS: load
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>hpt27xx: RocketRAID 27xx controller driver v1.1
hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2
hptnr: R750/DC7280 controller driver v1.0.1
cryptosoft0: <software crypto="">on motherboard
crypto: assign cryptosoft0 driver id 0, flags 100663296
crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 22 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 23 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 24 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 28 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 25 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 26 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 27 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0
padlock0: No ACE support.
acpi0: <ptltd rsdt="">on motherboard
ACPI: All ACPI Tables successfully acquired
PCIe: Memory Mapped configuration base @ 0xe0000000
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 0 vector 48
acpi0: Power Button (fixed)
cpu0: Processor \134_PR.CPU0 (ACPI ID 0) -> APIC ID 0
cpu0: <acpi cpu="">on acpi0
cpu0: switching to generic Cx mode
cpu1: Processor \134_PR_.CPU1 (ACPI ID 1) -> APIC ID 1
cpu1: <acpi cpu="">on acpi0
ACPI: Processor \134_PR_.CPU2 (ACPI ID 2) ignored
ACPI: Processor \134_PR_.CPU3 (ACPI ID 3) ignored
ACPI: Processor \134_PR_.CPU4 (ACPI ID 4) ignored
ACPI: Processor \134_PR_.CPU5 (ACPI ID 5) ignored
ACPI: Processor \134_PR_.CPU6 (ACPI ID 6) ignored
ACPI: Processor \134_PR_.CPU7 (ACPI ID 7) ignored
atrtc0: <at realtime="" clock="">port 0x70-0x71 irq 8 on acpi0
atrtc0: registered as a time-of-day clock (resolution 1000000us, adjustment 0.500000000s)
ioapic0: routing intpin 8 (ISA IRQ 8) to lapic 0 vector 49
Event timer "RTC" frequency 32768 Hz quality 0
attimer0: <at timer="">port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
ioapic0: routing intpin 2 (ISA IRQ 0) to lapic 0 vector 50
Event timer "i8254" frequency 1193182 Hz quality 100
ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
pci_link0: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 10 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link1: Index IRQ Rtd Ref IRQs
Initial Probe 0 11 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 11 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link2: Index IRQ Rtd Ref IRQs
Initial Probe 0 5 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 5 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link3: Index IRQ Rtd Ref IRQs
Initial Probe 0 7 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 7 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link4: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link5: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link6: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link7: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
pcib0: decoding 4 range 0-0xcf7
pcib0: decoding 3 range 0xa0000-0xbffff
pcib0: decoding 3 range 0xd0000-0xd3fff
pcib0: decoding 3 range 0xd4000-0xd7fff
pcib0: decoding 3 range 0xd8000-0xdbfff
pcib0: decoding 3 range 0xdc000-0xdffff
pcib0: decoding 3 range 0xe0000-0xe3fff
pcib0: decoding 3 range 0xc0000000-0xdfffffff
pcib0: decoding 4 range 0xd00-0xfdff
pcib0: decoding 3 range 0xfed40000-0xfed44fff
pci0: <acpi pci="" bus="">on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x8086, dev=0x2970, revid=0x02
domain=0, bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2972, revid=0x02
domain=0, bus=0, slot=2, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
MSI supports 1 message
map[10]: type Memory, range 32, base 0xd0000000, size 20, enabled
pcib0: allocated type 3 (0xd0000000-0xd00fffff) for rid 10 of pci0:0:2:0
map[18]: type Prefetchable Memory, range 64, base 0xc0000000, size 28, enabled
pcib0: allocated type 3 (0xc0000000-0xcfffffff) for rid 18 of pci0:0:2:0
map[20]: type I/O Port, range 32, base 0x30b0, size 3, enabled
pcib0: allocated type 4 (0x30b0-0x30b7) for rid 20 of pci0:0:2:0
pcib0: matched entry for 0.2.INTA
pcib0: slot 2 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x27d0, revid=0x01
domain=0, bus=0, slot=28, func=0
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0000, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
MSI supports 1 message
pcib0: matched entry for 0.28.INTA
pcib0: slot 28 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x27e0, revid=0x01
domain=0, bus=0, slot=28, func=4
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
MSI supports 1 message
pcib0: matched entry for 0.28.INTA
pcib0: slot 28 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x27e2, revid=0x01
domain=0, bus=0, slot=28, func=5
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0000, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=11
powerspec 2 supports D0 D3 current D0
MSI supports 1 message
pcib0: matched entry for 0.28.INTB
pcib0: slot 28 INTB hardwired to IRQ 17
found-> vendor=0x8086, dev=0x27c8, revid=0x01
domain=0, bus=0, slot=29, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
map[20]: type I/O Port, range 32, base 0x3000, size 5, enabled
pcib0: allocated type 4 (0x3000-0x301f) for rid 20 of pci0:0:29:0
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x27c9, revid=0x01
domain=0, bus=0, slot=29, func=1
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=11
map[20]: type I/O Port, range 32, base 0x3020, size 5, enabled
pcib0: allocated type 4 (0x3020-0x303f) for rid 20 of pci0:0:29:1
pcib0: matched entry for 0.29.INTB
pcib0: slot 29 INTB hardwired to IRQ 17
found-> vendor=0x8086, dev=0x27ca, revid=0x01
domain=0, bus=0, slot=29, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=5
map[20]: type I/O Port, range 32, base 0x3040, size 5, enabled
pcib0: allocated type 4 (0x3040-0x305f) for rid 20 of pci0:0:29:2
pcib0: matched entry for 0.29.INTC
pcib0: slot 29 INTC hardwired to IRQ 18
found-> vendor=0x8086, dev=0x27cb, revid=0x01
domain=0, bus=0, slot=29, func=3
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=7
map[20]: type I/O Port, range 32, base 0x3060, size 5, enabled
pcib0: allocated type 4 (0x3060-0x307f) for rid 20 of pci0:0:29:3
pcib0: matched entry for 0.29.INTD
pcib0: slot 29 INTD hardwired to IRQ 19
found-> vendor=0x8086, dev=0x27cc, revid=0x01
domain=0, bus=0, slot=29, func=7
class=0c-03-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
map[10]: type Memory, range 32, base 0xd0400000, size 10, enabled
pcib0: allocated type 3 (0xd0400000-0xd04003ff) for rid 10 of pci0:0:29:7
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x244e, revid=0xe1
domain=0, bus=0, slot=30, func=0
class=06-04-01, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x27b8, revid=0x01
domain=0, bus=0, slot=31, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x27c1, revid=0x01
domain=0, bus=0, slot=31, func=2
class=01-06-01, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=11
powerspec 2 supports D0 D3 current D0
MSI supports 1 message
map[10]: type I/O Port, range 32, base 0x30c8, size 3, enabled
pcib0: allocated type 4 (0x30c8-0x30cf) for rid 10 of pci0:0:31:2
map[14]: type I/O Port, range 32, base 0x30bc, size 2, enabled
pcib0: allocated type 4 (0x30bc-0x30bf) for rid 14 of pci0:0:31:2
map[18]: type I/O Port, range 32, base 0x30c0, size 3, enabled
pcib0: allocated type 4 (0x30c0-0x30c7) for rid 18 of pci0:0:31:2
map[1c]: type I/O Port, range 32, base 0x30b8, size 2, enabled
pcib0: allocated type 4 (0x30b8-0x30bb) for rid 1c of pci0:0:31:2
map[20]: type I/O Port, range 32, base 0x30a0, size 4, enabled
pcib0: allocated type 4 (0x30a0-0x30af) for rid 20 of pci0:0:31:2
map[24]: type Memory, range 32, base 0xd0400400, size 10, enabled
pcib0: allocated type 3 (0xd0400400-0xd04007ff) for rid 24 of pci0:0:31:2
pcib0: matched entry for 0.31.INTB
pcib0: slot 31 INTB hardwired to IRQ 17
found-> vendor=0x8086, dev=0x27da, revid=0x01
domain=0, bus=0, slot=31, func=3
class=0c-05-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=11
map[20]: type I/O Port, range 32, base 0x1100, size 5, enabled
pcib0: allocated type 4 (0x1100-0x111f) for rid 20 of pci0:0:31:3
pcib0: matched entry for 0.31.INTB
pcib0: slot 31 INTB hardwired to IRQ 17
vgapci0: <vga-compatible display="">port 0x30b0-0x30b7 mem 0xd0000000-0xd00fffff,0xc0000000-0xcfffffff irq 16 at device 2.0 on pci0
agp0: <intel 946gz="" svga="" controller="">on vgapci0
pcib0: allocated type 3 (0xd0100000-0xd0100fff) for rid 64 of agp0
agp0: Allocated flush page phys 0xd0100000 virt 0xfffff800d0100000
agp0: aperture size is 256M, detected 7676k stolen memory
agp0: AGP_I965_PGTBL_CTL2: 00000000
agp0: AGP_I855_GCC1: 0x30
agp0: AGP_I965_MSAC: 0x00
agp0: Mappable GTT entries: 65536
agp0: Total GTT entries: 131072
vgapci0: Boot video device
pcib1: <acpi pci-pci="" bridge="">irq 16 at device 28.0 on pci0
pcib1: domain 0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pci1: <acpi pci="" bus="">on pcib1
pci1: domain=0, physical bus=1
pcib2: <acpi pci-pci="" bridge="">irq 16 at device 28.4 on pci0
pcib2: domain 0
pcib2: secondary bus 2
pcib2: subordinate bus 2
pcib2: special decode ISA
pci2: <acpi pci="" bus="">on pcib2
pci2: domain=0, physical bus=2
pcib3: <acpi pci-pci="" bridge="">irq 17 at device 28.5 on pci0
pcib3: failed to allocate initial I/O port window: 0-0xfff
pcib3: failed to allocate initial memory window: 0-0xfffff
pcib3: failed to allocate initial prefetch window: 0-0xfffff
pcib3: domain 0
pcib3: secondary bus 3
pcib3: subordinate bus 3
pci3: <acpi pci="" bus="">on pcib3
pci3: domain=0, physical bus=3
uhci0: <intel 82801g="" (ich7)="" usb="" controller="" usb-a="">port 0x3000-0x301f irq 16 at device 29.0 on pci0
ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 0 vector 51
usbus0 on uhci0
uhci0: usbpf: Attached
uhci1: <intel 82801g="" (ich7)="" usb="" controller="" usb-b="">port 0x3020-0x303f irq 17 at device 29.1 on pci0
ioapic0: routing intpin 17 (PCI IRQ 17) to lapic 0 vector 52
usbus1 on uhci1
uhci1: usbpf: Attached
uhci2: <intel 82801g="" (ich7)="" usb="" controller="" usb-c="">port 0x3040-0x305f irq 18 at device 29.2 on pci0
ioapic0: routing intpin 18 (PCI IRQ 18) to lapic 0 vector 53
usbus2 on uhci2
uhci2: usbpf: Attached
uhci3: <intel 82801g="" (ich7)="" usb="" controller="" usb-d="">port 0x3060-0x307f irq 19 at device 29.3 on pci0
ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 0 vector 54
usbus3 on uhci3
uhci3: usbpf: Attached
ehci0: <intel 82801gb="" r="" (ich7)="" usb="" 2.0="" controller="">mem 0xd0400000-0xd04003ff irq 16 at device 29.7 on pci0
usbus4: EHCI version 1.0
usbus4 on ehci0
ehci0: usbpf: Attached
pcib4: <acpi pci-pci="" bridge="">at device 30.0 on pci0
pcib4: allocating non-ISA range 0x4000-0x40ff
pcib0: allocated type 4 (0x4000-0x40ff) for rid 1c of pcib4
pcib4: allocating non-ISA range 0x4400-0x44ff
pcib0: allocated type 4 (0x4400-0x44ff) for rid 1c of pcib4
pcib4: allocating non-ISA range 0x4800-0x48ff
pcib0: allocated type 4 (0x4800-0x48ff) for rid 1c of pcib4
pcib4: allocating non-ISA range 0x4c00-0x4cff
pcib0: allocated type 4 (0x4c00-0x4cff) for rid 1c of pcib4
pcib4: failed to allocate initial memory window: 0xd0100000-0xd01fffff
pcib4: domain 0
pcib4: secondary bus 4
pcib4: subordinate bus 4
pcib4: I/O decode 0x4000-0x4fff
pcib4: special decode ISA, subtractive
pci4: <acpi pci="" bus="">on pcib4
pci4: domain=0, physical bus=4
found-> vendor=0x8086, dev=0x1079, revid=0x03
domain=0, bus=4, slot=0, func=0
class=02-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0117, statreg=0x0230, cachelnsz=8 (dwords)
lattimer=0x34 (1560 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
map[10]: type Memory, range 64, base 0xd0180000, size 17, enabled
pcib0: allocated type 3 (0xd0180000-0xd019ffff) for rid 10 of pci0:4:0:0
map[18]: type Memory, range 64, base 0xd0100000, size 18, enabled
pci4: pci0:4:0:0 bar 0x18 failed to allocate
map[20]: type I/O Port, range 32, base 0x4000, size 6, enabled
pcib4: allocated I/O port range (0x4000-0x403f) for rid 20 of pci0:4:0:0
pcib4: matched entry for 4.0.INTA
pcib4: slot 0 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x1079, revid=0x03
domain=0, bus=4, slot=0, func=1
class=02-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0117, statreg=0x0230, cachelnsz=8 (dwords)
lattimer=0x34 (1560 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
intpin=b, irq=11
powerspec 2 supports D0 D3 current D0
map[10]: type Memory, range 64, base 0xd01a0000, size 17, enabled
pcib0: allocated type 3 (0xd01a0000-0xd01bffff) for rid 10 of pci0:4:0:1
map[18]: type Memory, range 64, base 0xd0140000, size 18, enabled
pcib0: allocated type 3 (0xd0140000-0xd017ffff) for rid 18 of pci0:4:0:1
map[20]: type I/O Port, range 32, base 0x4040, size 6, enabled
pcib4: allocated I/O port range (0x4040-0x407f) for rid 20 of pci0:4:0:1
pcib4: matched entry for 4.0.INTB
pcib4: slot 0 INTB hardwired to IRQ 17
em0: <intel(r) 1000="" pro="" legacy="" network="" connection="" 1.0.6="">port 0x4000-0x403f mem 0xd0180000-0xd019ffff irq 16 at device 0.0 on pci4
em0: bpf attached
em1: <intel(r) 1000="" pro="" legacy="" network="" connection="" 1.0.6="">port 0x4040-0x407f mem 0xd01a0000-0xd01bffff,0xd0140000-0xd017ffff irq 17 at device 0.1 on pci4
em1: bpf attached
isab0: <pci-isa bridge="">at device 31.0 on pci0
isa0: <isa bus="">on isab0
ahci0: <intel ich7="" ahci="" sata="" controller="">port 0x30c8-0x30cf,0x30bc-0x30bf,0x30c0-0x30c7,0x30b8-0x30bb,0x30a0-0x30af mem 0xd0400400-0xd04007ff irq 17 at device 31.2 on pci0
ahci0: attempting to allocate 1 MSI vectors (1 supported)
msi: routing MSI IRQ 256 to local APIC 0 vector 55
ahci0: using IRQ 256 for MSI
ahci0: AHCI v1.10 with 4 3Gbps ports, Port Multiplier not supported
ahci0: Caps: 64bit NCQ ALP AL CLO 3Gbps PMD SSC PSC 32cmd 4ports
ahcich0: <ahci channel="">at channel 0 on ahci0
ahcich0: Caps: HPCP
ahcich1: <ahci channel="">at channel 1 on ahci0
ahcich1: Caps: HPCP
ahcich2: <ahci channel="">at channel 2 on ahci0
ahcich2: Caps: HPCP
ahcich3: <ahci channel="">at channel 3 on ahci0
ahcich3: Caps: HPCP
pci0: <serial bus,="" smbus="">at device 31.3 (no driver attached)
acpi_button0: <power button="">on acpi0
atkbdc0: <keyboard controller="" (i8042)="">port 0x60,0x64 irq 1 on acpi0
atkbd0: <at keyboard="">irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0xffffffff (1)
atkbd: failed to reset the keyboard.
kbd0 at atkbd0
kbd0: atkbd0, AT 84 (1), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 0 vector 56
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
psmcpnp0: <ps 2="" mouse="" port="">irq 12 on acpi0
psm0: current command byte:0067
psm0: failed to reset the aux device.
fdc0: <floppy drive="" controller="">port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: ic_type 90 part_id 80
ioapic0: routing intpin 6 (ISA IRQ 6) to lapic 0 vector 57
acpi0: wakeup code va 0xfffffe0045d84000 pa 0x94000
ahc_isa_identify 0: ioport 0xc00 alloc failed
ahc_isa_identify 1: ioport 0x1c00 alloc failed
ahc_isa_identify 2: ioport 0x2c00 alloc failed
ahc_isa_identify 3: ioport 0x3c00 alloc failed
ahc_isa_identify 4: ioport 0x4c00 alloc failed
ahc_isa_identify 5: ioport 0x5c00 alloc failed
ahc_isa_identify 6: ioport 0x6c00 alloc failed
ahc_isa_identify 7: ioport 0x7c00 alloc failed
ahc_isa_identify 8: ioport 0x8c00 alloc failed
ahc_isa_identify 9: ioport 0x9c00 alloc failed
ahc_isa_identify 10: ioport 0xac00 alloc failed
ahc_isa_identify 11: ioport 0xbc00 alloc failed
ahc_isa_identify 12: ioport 0xcc00 alloc failed
ahc_isa_identify 13: ioport 0xdc00 alloc failed
ahc_isa_identify 14: ioport 0xec00 alloc failed
ex_isa_identify()
pcib0: allocated type 3 (0xa0000-0xa07ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa0800-0xa0fff) for rid 0 of orm0
pcib0: allocated type 3 (0xa1000-0xa17ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa1800-0xa1fff) for rid 0 of orm0
pcib0: allocated type 3 (0xa2000-0xa27ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa2800-0xa2fff) for rid 0 of orm0
pcib0: allocated type 3 (0xa3000-0xa37ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa3800-0xa3fff) for rid 0 of orm0
pcib0: allocated type 3 (0xa4000-0xa47ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa4800-0xa4fff) for rid 0 of orm0
pcib0: allocated type 3 (0xa5000-0xa57ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa5800-0xa5fff) for rid 0 of orm0
pcib0: allocated type 3 (0xa6000-0xa67ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa6800-0xa6fff) for rid 0 of orm0
pcib0: allocated type 3 (0xa7000-0xa77ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa7800-0xa7fff) for rid 0 of orm0
pcib0: allocated type 3 (0xa8000-0xa87ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa8800-0xa8fff) for rid 0 of orm0
pcib0: allocated type 3 (0xa9000-0xa97ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa9800-0xa9fff) for rid 0 of orm0
pcib0: allocated type 3 (0xaa000-0xaa7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xaa800-0xaafff) for rid 0 of orm0
pcib0: allocated type 3 (0xab000-0xab7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xab800-0xabfff) for rid 0 of orm0
pcib0: allocated type 3 (0xac000-0xac7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xac800-0xacfff) for rid 0 of orm0
pcib0: allocated type 3 (0xad000-0xad7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xad800-0xadfff) for rid 0 of orm0
pcib0: allocated type 3 (0xae000-0xae7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xae800-0xaefff) for rid 0 of orm0
pcib0: allocated type 3 (0xaf000-0xaf7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xaf800-0xaffff) for rid 0 of orm0
pcib0: allocated type 3 (0xb0000-0xb07ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb0800-0xb0fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb1000-0xb17ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb1800-0xb1fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb2000-0xb27ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb2800-0xb2fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb3000-0xb37ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb3800-0xb3fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb4000-0xb47ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb4800-0xb4fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb5000-0xb57ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb5800-0xb5fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb6000-0xb67ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb6800-0xb6fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb7000-0xb77ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb7800-0xb7fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb8000-0xb87ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb8800-0xb8fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb9000-0xb97ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb9800-0xb9fff) for rid 0 of orm0
pcib0: allocated type 3 (0xba000-0xba7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xba800-0xbafff) for rid 0 of orm0
pcib0: allocated type 3 (0xbb000-0xbb7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xbb800-0xbbfff) for rid 0 of orm0
pcib0: allocated type 3 (0xbc000-0xbc7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xbc800-0xbcfff) for rid 0 of orm0
pcib0: allocated type 3 (0xbd000-0xbd7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xbd800-0xbdfff) for rid 0 of orm0
pcib0: allocated type 3 (0xbe000-0xbe7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xbe800-0xbefff) for rid 0 of orm0
pcib0: allocated type 3 (0xbf000-0xbf7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xbf800-0xbffff) for rid 0 of orm0
pcib0: allocated type 3 (0xd0000-0xd07ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd0800-0xd0fff) for rid 2 of orm0
pcib0: allocated type 3 (0xd1000-0xd17ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd1800-0xd1fff) for rid 2 of orm0
pcib0: allocated type 3 (0xd2000-0xd27ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd2800-0xd2fff) for rid 2 of orm0
pcib0: allocated type 3 (0xd3000-0xd37ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd3800-0xd3fff) for rid 2 of orm0
pcib0: allocated type 3 (0xd4000-0xd47ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd4800-0xd4fff) for rid 2 of orm0
pcib0: allocated type 3 (0xd5000-0xd57ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd5800-0xd5fff) for rid 2 of orm0
pcib0: allocated type 3 (0xd6000-0xd67ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd6800-0xd6fff) for rid 2 of orm0
pcib0: allocated type 3 (0xd7000-0xd77ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd7800-0xd7fff) for rid 2 of orm0
pcib0: allocated type 3 (0xd8000-0xd87ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd8800-0xd8fff) for rid 2 of orm0
pcib0: allocated type 3 (0xd9000-0xd97ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd9800-0xd9fff) for rid 2 of orm0
pcib0: allocated type 3 (0xda000-0xda7ff) for rid 2 of orm0
pcib0: allocated type 3 (0xda800-0xdafff) for rid 2 of orm0
pcib0: allocated type 3 (0xdb000-0xdb7ff) for rid 2 of orm0
pcib0: allocated type 3 (0xdb800-0xdbfff) for rid 2 of orm0
pcib0: allocated type 3 (0xdc000-0xdc7ff) for rid 2 of orm0
pcib0: allocated type 3 (0xdc800-0xdcfff) for rid 2 of orm0
pcib0: allocated type 3 (0xdd000-0xdd7ff) for rid 2 of orm0
pcib0: allocated type 3 (0xdd800-0xddfff) for rid 2 of orm0
pcib0: allocated type 3 (0xde000-0xde7ff) for rid 2 of orm0
pcib0: allocated type 3 (0xde800-0xdefff) for rid 2 of orm0
pcib0: allocated type 3 (0xdf000-0xdf7ff) for rid 2 of orm0
pcib0: allocated type 3 (0xdf800-0xdffff) for rid 2 of orm0
pcib0: allocated type 3 (0xe0000-0xe07ff) for rid 2 of orm0
pcib0: allocated type 3 (0xe0800-0xe0fff) for rid 2 of orm0
pcib0: allocated type 3 (0xe1000-0xe17ff) for rid 2 of orm0
pcib0: allocated type 3 (0xe1800-0xe1fff) for rid 2 of orm0
pcib0: allocated type 3 (0xe2000-0xe27ff) for rid 2 of orm0
pcib0: allocated type 3 (0xe2800-0xe2fff) for rid 2 of orm0
pcib0: allocated type 3 (0xe3000-0xe37ff) for rid 2 of orm0
pcib0: allocated type 3 (0xe3800-0xe3fff) for rid 2 of orm0
isa_probe_children: disabling PnP devices
atkbdc: atkbdc0 already exists; skipping it
atrtc: atrtc0 already exists; skipping it
attimer: attimer0 already exists; skipping it
fdc: fdc0 already exists; skipping it
sc: sc0 already exists; skipping it
isa_probe_children: probing non-PnP devices
orm0: <isa option="" roms="">at iomem 0xc0000-0xcafff,0xcb000-0xcbfff on isa0
sc0: <system console="">at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
pcib0: allocated type 4 (0x3c0-0x3df) for rid 0 of vga0
pcib0: allocated type 3 (0xa0000-0xbffff) for rid 0 of vga0
ppc0: cannot reserve I/O port range
ppc0 failed to probe at irq 7 on isa0
pcib0: allocated type 4 (0x3f8-0x3ff) for rid 0 of uart0
uart0 failed to probe at port 0x3f8-0x3ff irq 4 on isa0
pcib0: allocated type 4 (0x2f8-0x2ff) for rid 0 of uart1
uart1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
wbwd0 failed to probe on isa0
isa_probe_children: probing PnP devices
est0: enabling SpeedStep
est0: <enhanced speedstep="" frequency="" control="">on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr b200b2006000b20
device_attach: est0 attach returned 6
p4tcc0: <cpu frequency="" thermal="" control="">on cpu0
est1: <enhanced speedstep="" frequency="" control="">on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr b200b2006000b20
device_attach: est1 attach returned 6
p4tcc1: <cpu frequency="" thermal="" control="">on cpu1
Device configuration finished.
procfs registered
lapic: Divisor 2, Frequency 99751952 Hz
Timecounters tick every 1.000 msec
pflog0: bpf attached
crypto: <crypto device="">vlan: initialized, using hash tables with chaining
tcp_init: net.inet.tcp.tcbhashsize auto tuned to 32768
IPsec: Initialized Security Association Processing.
pfsync0: bpf attached
lo0: bpf attached
enc0: bpf attached
hpt27xx: no controller detected.
hptrr: no controller detected.
hptnr: no controller detected.
random: unblocking device.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0
ahcich0: AHCI reset…
ahcich0: SATA connect time=900us status=00000113
ahcich0: AHCI reset: device found
ahcich1: AHCI reset...
ahcich1: SATA offline status=00000004
ahcich1: AHCI reset: device not found
ahcich2: AHCI reset...
ugen1.1: <intel>at usbus1
uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
ugen0.1: <intel>at usbus0
uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
ugen3.1: <intel>at usbus3
uhub2: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
ugen2.1: <intel>at usbus2
uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus2
ugen4.1: <intel>at usbus4
uhub4: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus4
ahcich2: SATA connect time=1000us status=00000113
ahcich2: AHCI reset: device found
ahcich2: AHCI reset: device ready after 0ms
ahcich3: AHCI reset...
ahcich3: SATA offline status=00000004
ahcich3: AHCI reset: device not found
ahcich0: AHCI reset: device ready after 100ms
pass0 at ahcich0 bus 0 scbus0 target 0 lun 0
GEOM: new disk cd0
cd0 at ahcich2 bus 0 scbus2 target 0 lun 0
cd0: <tsstcorp cddvdw="" ts-h653n="" 0208="">Removable CD-ROM SCSI-0 device
cd0: 150.000MB/s transfers (SATA 1.x, UDMA2, ATAPI 12bytes, PIO 8192bytes)
cd0: Attempt to query device size failed: NOT READY, Medium not present - tray closed
pass0: <st3250310as 3.aaf="">ATA-7 SATA 1.x device
pass0: Serial Number 6RYAJH0Y
pass0: 150.000MB/s transfers (SATA 1.x, UDMA6, PIO 8192bytes)
pass0: Command Queueing enabled
pass1 at ahcich2 bus 0 scbus2 target 0 lun 0
pass1: <tsstcorp cddvdw="" ts-h653n="" 0208="">Removable CD-ROM SCSI-0 device
pass1: 150.000MB/s transfers (SATA 1.x, UDMA2, ATAPI 12bytes, PIO 8192bytes)
ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
ada0: <st3250310as 3.aaf="">ATA-7 SATA 1.x device
ada0: Serial Number 6RYAJH0Y
ada0: 150.000MB/s transfers (SATA 1.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 238475MB (488397168 512 byte sectors: 16H 63S/T 16383C)
ada0: Previously was known as ad4
GEOM: new disk ada0
Netvsc initializing... done!
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x01000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 1 vector 48
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 1 vector 49
ioapic0: routing intpin 17 (PCI IRQ 17) to lapic 1 vector 50
ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 1 vector 51
SMP: passed TSC synchronization test
TSC timecounter discards lower 1 bit(s)
Timecounter "TSC-low" frequency 1097271219 Hz quality 1000
Root mount waiting for: usbus4 usbus3 usbus2 usbus1 usbus0
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
Root mount waiting for: usbus4
Root mount waiting for: usbus4
uhub4: 8 ports with 8 removable, self powered
Root mount waiting for: usbus4
Trying to mount root from ufs:/dev/ada0s1a [rw]…
WARNING: / was not properly dismounted
start_init: trying /sbin/init
ugen0.2: <microsoft>at usbus0
ukbd0: <microsoft 0="" 2="" natural="" ergonomic="" keyboard="" 4000,="" class="" 0,="" rev="" 2.00="" 1.73,="" addr="">on usbus0
kbd2 at ukbd0
kbd2: ukbd0, generic (0), config:0x0, flags:0x3d0000
uhid0: <microsoft 0="" 2="" natural="" ergonomic="" keyboard="" 4000,="" class="" 0,="" rev="" 2.00="" 1.73,="" addr="">on usbus0
ugen3.2: <crystalfontz america="">at usbus3
umodem0: <crystalfontz 2="" america="" cfa-735="" display,="" class="" 0,="" rev="" 2.00="" 2.00,="" addr="">on usbus3
umodem0: data interface 1, has no CM over data, has no break
coretemp0: <cpu on-die="" thermal="" sensors="">on cpu0
coretemp0: Setting TjMax=85
est0: <enhanced speedstep="" frequency="" control="">on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr b200b2006000b20
device_attach: est0 attach returned 6
coretemp1: <cpu on-die="" thermal="" sensors="">on cpu1
coretemp1: Setting TjMax=85
est1: <enhanced speedstep="" frequency="" control="">on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr b200b2006000b20
device_attach: est1 attach returned 6
em1: Link is up 1000 Mbps Full Duplex
em1: link state changed to UP
pflog0: promiscuous mode enabled
em0: Link is up 1000 Mbps Full Duplex
em0: link state changed to UP
em1: promiscuous mode enabled
em0: promiscuous mode enabled
[2.2-RC]</enhanced></cpu></enhanced></cpu></crystalfontz></crystalfontz></microsoft></microsoft></microsoft></st3250310as></tsstcorp></st3250310as></tsstcorp></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></crypto></cpu></enhanced></cpu></enhanced></generic></system></isa></floppy></ps></at></keyboard></power></serial></ahci></ahci></ahci></ahci></intel></isa></pci-isa></intel(r)></intel(r)></acpi></acpi></intel></intel></intel></intel></intel></acpi></acpi></acpi></acpi></acpi></acpi></intel></vga-compatible></acpi></acpi></at></at></acpi></acpi></ptltd ></software></memory>_</crypto></software,></software,></null></version></ptltd ></lahf></syscall,lm></sse3,dtes64,mon,ds_cpl,est,tm2,ssse3,cx16,xtpr,pdcm></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe> -
Here is with the built on lan ports and the USB lan to get 2 ports.
LOADER.CONF
autoboot_delay="3"
vm.kmem_size="435544320"
vm.kmem_size_max="535544320"
hw.acpi.host_mem_start="0xf0000000"
boot_verbose="1"
comconsole_speed="115200"
hw.usb.no_pf="1"dmesg log
Table 'FACP' at 0xbf68ad08
Table 'TCPA' at 0xbf68ad8c
Table 'MCFG' at 0xbf68adbe
Table 'APIC' at 0xbf68adfa
APIC: Found table at 0xbf68adfa
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 0 ACPI ID 0: enabled
SMP: Added CPU 0 (AP)
MADT: Found CPU APIC ID 1 ACPI ID 1: enabled
SMP: Added CPU 1 (AP)
Copyright 1992-2014 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 10.1-RELEASE-p1 #0 fd28f0b(releng/10.1)-dirty: Sun Dec 14 23:42:20 CST 2014
root@pfsense-22-amd64-builder:/usr/obj.amd64/usr/pfSensesrc/src/sys/pfSense_SMP.10 amd64
FreeBSD clang version 3.4.1 (tags/RELEASE_34/dot1-final 208032) 20140512
Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff824c7000.
Calibrating TSC clock ... TSC clock: 2194546673 Hz
CPU: Intel(R) Pentium(R) Dual CPU E2200 @ 2.20GHz (2194.55-MHz K8-class CPU)
Origin = "GenuineIntel" Id = 0x6fd Family = 0x6 Model = 0xf Stepping = 13
Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0xe39d <sse3,dtes64,mon,ds_cpl,est,tm2,ssse3,cx16,xtpr,pdcm>AMD Features=0x20000800 <syscall,lm>AMD Features2=0x1 <lahf>TSC: P-state invariant, performance statistics
real memory = 4294967296 (4096 MB)
Physical memory chunk(s):
0x0000000000010000 - 0x0000000000099fff, 565248 bytes (138 pages)
0x0000000000100000 - 0x00000000001fffff, 1048576 bytes (256 pages)
0x00000000024f6000 - 0x00000000b73f0fff, 3035607040 bytes (741115 pages)
0x0000000100000000 - 0x000000013ffe7fff, 1073643520 bytes (262120 pages)
avail memory = 4088520704 (3899 MB)
Event timer "LAPIC" quality 400
ACPI APIC Table: <ptltd ="" apic ="">INTR: Adding local APIC 1 as a target
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
APIC: CPU 0 has ACPI ID 0
APIC: CPU 1 has ACPI ID 1
x86bios: IVT 0x000000-0x0004ff at 0xfffff80000000000
x86bios: SSEG 0x098000-0x098fff at 0xfffffe003f3a4000
x86bios: EBDA 0x09d000-0x09ffff at 0xfffff8000009d000
x86bios: ROM 0x0a0000-0x0fefff at 0xfffff800000a0000
XEN: CPU 0 has VCPU ID 0
XEN: CPU 1 has VCPU ID 1
ULE: setup cpu 0
ULE: setup cpu 1
ACPI: RSDP 0xf7260 00014 (v00 PTLTD )
ACPI: RSDT 0xbf683b6d 00060 (v01 PTLTD RSDT 06040000 LTP 00000000)
ACPI: FACP 0xbf68ad08 00084 (v01 SUPRMC 06040000 PTL 00000003)
ACPI: DSDT 0xbf68569f 05669 (v01 INTEL BR_WATER 06040000 MSFT 03000001)
ACPI: FACS 0xbf68bfc0 00040
ACPI: TCPA 0xbf68ad8c 00032 (v01 SMC 06040000 PTL 00000000)
ACPI: MCFG 0xbf68adbe 0003C (v01 PTLTD MCFG 06040000 LTP 00000000)
ACPI: APIC 0xbf68adfa 00068 (v01 PTLTD ? APIC 06040000 LTP 00000000)
ACPI: BOOT 0xbf68ae62 00028 (v01 PTLTD $SBFTBL$ 06040000 LTP 00000001)
ACPI: SLIC 0xbf68ae8a 00176 (v01 OEMID_ OEMTABLE 06040000 LTP 00000000)
ACPI: SSDT 0xbf685440 0025F (v01 PmRef Cpu0Tst 00003000 INTL 20050228)
ACPI: SSDT 0xbf68539a 000A6 (v01 PmRef Cpu7Tst 00003000 INTL 20050228)
ACPI: SSDT 0xbf6852f4 000A6 (v01 PmRef Cpu6Tst 00003000 INTL 20050228)
ACPI: SSDT 0xbf68524e 000A6 (v01 PmRef Cpu5Tst 00003000 INTL 20050228)
ACPI: SSDT 0xbf6851a8 000A6 (v01 PmRef Cpu4Tst 00003000 INTL 20050228)
ACPI: SSDT 0xbf685102 000A6 (v01 PmRef Cpu3Tst 00003000 INTL 20050228)
ACPI: SSDT 0xbf68505c 000A6 (v01 PmRef Cpu2Tst 00003000 INTL 20050228)
ACPI: SSDT 0xbf684fb6 000A6 (v01 PmRef Cpu1Tst 00003000 INTL 20050228)
ACPI: SSDT 0xbf683bcd 013E9 (v01 PmRef CpuPm 00003000 INTL 20050228)
MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000
ioapic0: Routing external 8259A's -> intpin 0
lapic0: Routing NMI -> LINT1
lapic0: LINT1 trigger: edge
lapic0: LINT1 polarity: high
lapic1: Routing NMI -> LINT1
lapic1: LINT1 trigger: edge
lapic1: LINT1 polarity: high
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0 <version 2.0="">irqs 0-23 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00000200 err: 0x000000f0 pmc: 0x00010400
firmware: 'iwn4965fw' version 0: 187972 bytes loaded at 0xffffffff81a1b80c
firmware: 'iwn5000fw' version 0: 340696 bytes loaded at 0xffffffff81a496fc
firmware: 'iwn5150fw' version 0: 337400 bytes loaded at 0xffffffff81a9ca84
firmware: 'iwn6000fw' version 0: 454608 bytes loaded at 0xffffffff81aef12c
firmware: 'wpifw' version 153229: 150100 bytes loaded at 0xffffffff81df6cc4
firmware: 'iwn6000g2afw' version 0: 444128 bytes loaded at 0xffffffff81b5e1ac
firmware: 'iwn6000g2bfw' version 0: 460912 bytes loaded at 0xffffffff81bca93c
firmware: 'iwn6050fw' version 0: 469780 bytes loaded at 0xffffffff81c3b25c
snd_unit_init() u=0x00ff8000 [512] d=0x00007c00 [32] c=0x000003ff [1024]
feeder_register: snd_unit=-1 snd_maxautovchans=16 latency=5 feeder_rate_min=1 feeder_rate_max=2016000 feeder_rate_round=25
firmware: 't4fw_cfg' version 0: 3059 bytes loaded at 0xffffffff8164c804
firmware: 't4fw_cfg_uwire' version 0: 21284 bytes loaded at 0xffffffff8164d3f7
firmware: 't4fw' version 0: 512512 bytes loaded at 0xffffffff8165271b
firmware: 't5fw_cfg' version 0: 3435 bytes loaded at 0xffffffff816cf9cc
firmware: 't5fw' version 0: 513024 bytes loaded at 0xffffffff816d0737
firmware: 'mw88W8363fw' version 0: 94940 bytes loaded at 0xffffffff81cb992c
firmware: 'mwlboot' version 0: 2280 bytes loaded at 0xffffffff81cd0c08
firmware: 'rsu-rtl8712fw' version 120: 122328 bytes loaded at 0xffffffff81dbaae4
firmware: 'runfw' version 0: 8192 bytes loaded at 0xffffffff81dd8ca4
firmware: 'rt2561fw' version 0: 8192 bytes loaded at 0xffffffff81d5aff4
wlan: mac acl policy registered
firmware: 'rt2561sfw' version 0: 8192 bytes loaded at 0xffffffff81d5d0a4
firmware: 'urtwn-rtl8188eufw' version 111: 13904 bytes loaded at 0xffffffff81ddb5dc
firmware: 'urtwn-rtl8192cfwT' version 111: 16076 bytes loaded at 0xffffffff81ddecdc
firmware: 'urtwn-rtl8192cfwU' version 111: 16076 bytes loaded at 0xffffffff81de2c54
firmware: 'rt2661fw' version 0: 8192 bytes loaded at 0xffffffff81d5f154
firmware: 'rt2860fw' version 0: 8192 bytes loaded at 0xffffffff81d61204
firmware: 'mxge_eth_z8e' version 377284: 120629 bytes loaded at 0xffffffff81cd16c0
wlan: <802.11 Link Layer>
firmware: 'mxge_ethp_z8e' version 387604: 121317 bytes loaded at 0xffffffff81ceeeb0
firmware: 'mxge_rss_eth_z8e' version 534724: 151912 bytes loaded at 0xffffffff81d0c950
firmware: 'mxge_rss_ethp_z8e' version 544468: 152837 bytes loaded at 0xffffffff81d31b70
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff80606640, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff806066f0, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff806067a0, 0) error 1
iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/.
iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_bss_fw, 0xffffffff8062de10, 0) error 1
iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/.
iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffffffff8062dec0, 0) error 1
iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/.
iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffffffff8062df70, 0) error 1
firmware: 'iwn1000fw' version 0: 337520 bytes loaded at 0xffffffff8187260c
firmware: 'iwn2000fw' version 0: 695876 bytes loaded at 0xffffffff818c4d2c
firmware: 'iwn2030fw' version 0: 707392 bytes loaded at 0xffffffff8196ec1c
Hardware, Intel Secure Key RNG: RDRAND is not present
Hardware, VIA Nehemiah Padlock RNG: VIA Padlock RNG not present
null: <null device,="" zero="" device="">Falling back to <software, yarrow="">random adaptor
random: <software, yarrow="">initialized
nfslock: pseudo-device
crypto: <crypto core="">VESA: INT 0x10 vector 0xc000:0x0014
VESA: information block
0000 56 45 53 41 00 03 00 01 00 99 01 00 00 00 40 00
0010 00 99 77 00 00 01 38 01 00 99 4a 01 00 99 73 01
0020 00 99 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0030 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0040 60 01 61 01 62 01 63 01 64 01 65 01 66 01 67 01
0050 68 01 3c 01 4d 01 5c 01 3a 01 4b 01 5a 01 07 01
0060 1a 01 1b 01 05 01 17 01 18 01 12 01 14 01 15 01
0070 01 01 03 01 11 01 ff ff 00 00 00 00 00 00 00 00
0080 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0090 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00a0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00c0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0100 49 6e 74 65 6c 28 72 29 42 72 6f 61 64 77 61 74
0110 65 72 2d 47 20 47 72 61 70 68 69 63 73 20 43 68
0120 69 70 20 41 63 63 65 6c 65 72 61 74 65 64 20 56
0130 47 41 20 42 49 4f 53 00 49 6e 74 65 6c 20 43 6f
0140 72 70 6f 72 61 74 69 6f 6e 00 49 6e 74 65 6c 28
0150 72 29 42 72 6f 61 64 77 61 74 65 72 2d 47 20 47
0160 72 61 70 68 69 63 73 20 43 6f 6e 74 72 6f 6c 6c
0170 65 72 00 48 61 72 64 77 61 72 65 20 56 65 72 73
0180 69 6f 6e 20 30 2e 30 00 00 00 00 00 00 00 00 00
0190 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01a0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01c0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
VESA: 17 mode(s) found
VESA: v3.0, 7616k memory, flags:0x1, mode table:0xfffffe003f3fa040 (99000040)
VESA: Intel(r)Broadwater-G Graphics Chip Accelerated VGA BIOS
VESA: Intel Corporation Intel(r)Broadwater-G Graphics Controller Hardware Version 0.0
io: VMBUS: load
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>hpt27xx: RocketRAID 27xx controller driver v1.1
hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2
hptnr: R750/DC7280 controller driver v1.0.1
cryptosoft0: <software crypto="">on motherboard
crypto: assign cryptosoft0 driver id 0, flags 100663296
crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 22 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 23 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 24 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 28 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 25 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 26 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 27 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0
padlock0: No ACE support.
acpi0: <ptltd rsdt="">on motherboard
ACPI: All ACPI Tables successfully acquired
PCIe: Memory Mapped configuration base @ 0xe0000000
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 0 vector 48
acpi0: Power Button (fixed)
cpu0: Processor \134_PR.CPU0 (ACPI ID 0) -> APIC ID 0
cpu0: <acpi cpu="">on acpi0
cpu0: switching to generic Cx mode
cpu1: Processor \134_PR_.CPU1 (ACPI ID 1) -> APIC ID 1
cpu1: <acpi cpu="">on acpi0
ACPI: Processor \134_PR_.CPU2 (ACPI ID 2) ignored
ACPI: Processor \134_PR_.CPU3 (ACPI ID 3) ignored
ACPI: Processor \134_PR_.CPU4 (ACPI ID 4) ignored
ACPI: Processor \134_PR_.CPU5 (ACPI ID 5) ignored
ACPI: Processor \134_PR_.CPU6 (ACPI ID 6) ignored
ACPI: Processor \134_PR_.CPU7 (ACPI ID 7) ignored
atrtc0: <at realtime="" clock="">port 0x70-0x71 irq 8 on acpi0
atrtc0: registered as a time-of-day clock (resolution 1000000us, adjustment 0.500000000s)
ioapic0: routing intpin 8 (ISA IRQ 8) to lapic 0 vector 49
Event timer "RTC" frequency 32768 Hz quality 0
attimer0: <at timer="">port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
ioapic0: routing intpin 2 (ISA IRQ 0) to lapic 0 vector 50
Event timer "i8254" frequency 1193182 Hz quality 100
ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
pci_link0: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 10 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link1: Index IRQ Rtd Ref IRQs
Initial Probe 0 11 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 11 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link2: Index IRQ Rtd Ref IRQs
Initial Probe 0 5 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 5 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link3: Index IRQ Rtd Ref IRQs
Initial Probe 0 7 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 7 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link4: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link5: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link6: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pci_link7: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 12 14 15
pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
pcib0: decoding 4 range 0-0xcf7
pcib0: decoding 3 range 0xa0000-0xbffff
pcib0: decoding 3 range 0xd0000-0xd3fff
pcib0: decoding 3 range 0xd4000-0xd7fff
pcib0: decoding 3 range 0xd8000-0xdbfff
pcib0: decoding 3 range 0xdc000-0xdffff
pcib0: decoding 3 range 0xe0000-0xe3fff
pcib0: decoding 3 range 0xc0000000-0xdfffffff
pcib0: decoding 4 range 0xd00-0xfdff
pcib0: decoding 3 range 0xfed40000-0xfed44fff
pci0: <acpi pci="" bus="">on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x8086, dev=0x2970, revid=0x02
domain=0, bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2972, revid=0x02
domain=0, bus=0, slot=2, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
MSI supports 1 message
map[10]: type Memory, range 32, base 0xd0000000, size 20, enabled
pcib0: allocated type 3 (0xd0000000-0xd00fffff) for rid 10 of pci0:0:2:0
map[18]: type Prefetchable Memory, range 64, base 0xc0000000, size 28, enabled
pcib0: allocated type 3 (0xc0000000-0xcfffffff) for rid 18 of pci0:0:2:0
map[20]: type I/O Port, range 32, base 0x30b0, size 3, enabled
pcib0: allocated type 4 (0x30b0-0x30b7) for rid 20 of pci0:0:2:0
pcib0: matched entry for 0.2.INTA
pcib0: slot 2 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x27d0, revid=0x01
domain=0, bus=0, slot=28, func=0
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0000, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
MSI supports 1 message
pcib0: matched entry for 0.28.INTA
pcib0: slot 28 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x27e0, revid=0x01
domain=0, bus=0, slot=28, func=4
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
MSI supports 1 message
pcib0: matched entry for 0.28.INTA
pcib0: slot 28 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x27e2, revid=0x01
domain=0, bus=0, slot=28, func=5
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
intpin=b, irq=11
powerspec 2 supports D0 D3 current D0
MSI supports 1 message
pcib0: matched entry for 0.28.INTB
pcib0: slot 28 INTB hardwired to IRQ 17
found-> vendor=0x8086, dev=0x27c8, revid=0x01
domain=0, bus=0, slot=29, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
map[20]: type I/O Port, range 32, base 0x3000, size 5, enabled
pcib0: allocated type 4 (0x3000-0x301f) for rid 20 of pci0:0:29:0
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x27c9, revid=0x01
domain=0, bus=0, slot=29, func=1
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=11
map[20]: type I/O Port, range 32, base 0x3020, size 5, enabled
pcib0: allocated type 4 (0x3020-0x303f) for rid 20 of pci0:0:29:1
pcib0: matched entry for 0.29.INTB
pcib0: slot 29 INTB hardwired to IRQ 17
found-> vendor=0x8086, dev=0x27ca, revid=0x01
domain=0, bus=0, slot=29, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=5
map[20]: type I/O Port, range 32, base 0x3040, size 5, enabled
pcib0: allocated type 4 (0x3040-0x305f) for rid 20 of pci0:0:29:2
pcib0: matched entry for 0.29.INTC
pcib0: slot 29 INTC hardwired to IRQ 18
found-> vendor=0x8086, dev=0x27cb, revid=0x01
domain=0, bus=0, slot=29, func=3
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=7
map[20]: type I/O Port, range 32, base 0x3060, size 5, enabled
pcib0: allocated type 4 (0x3060-0x307f) for rid 20 of pci0:0:29:3
pcib0: matched entry for 0.29.INTD
pcib0: slot 29 INTD hardwired to IRQ 19
found-> vendor=0x8086, dev=0x27cc, revid=0x01
domain=0, bus=0, slot=29, func=7
class=0c-03-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
map[10]: type Memory, range 32, base 0xd0500000, size 10, enabled
pcib0: allocated type 3 (0xd0500000-0xd05003ff) for rid 10 of pci0:0:29:7
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x244e, revid=0xe1
domain=0, bus=0, slot=30, func=0
class=06-04-01, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x27b8, revid=0x01
domain=0, bus=0, slot=31, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x27c1, revid=0x01
domain=0, bus=0, slot=31, func=2
class=01-06-01, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=11
powerspec 2 supports D0 D3 current D0
MSI supports 1 message
map[10]: type I/O Port, range 32, base 0x30c8, size 3, enabled
pcib0: allocated type 4 (0x30c8-0x30cf) for rid 10 of pci0:0:31:2
map[14]: type I/O Port, range 32, base 0x30bc, size 2, enabled
pcib0: allocated type 4 (0x30bc-0x30bf) for rid 14 of pci0:0:31:2
map[18]: type I/O Port, range 32, base 0x30c0, size 3, enabled
pcib0: allocated type 4 (0x30c0-0x30c7) for rid 18 of pci0:0:31:2
map[1c]: type I/O Port, range 32, base 0x30b8, size 2, enabled
pcib0: allocated type 4 (0x30b8-0x30bb) for rid 1c of pci0:0:31:2
map[20]: type I/O Port, range 32, base 0x30a0, size 4, enabled
pcib0: allocated type 4 (0x30a0-0x30af) for rid 20 of pci0:0:31:2
map[24]: type Memory, range 32, base 0xd0500400, size 10, enabled
pcib0: allocated type 3 (0xd0500400-0xd05007ff) for rid 24 of pci0:0:31:2
pcib0: matched entry for 0.31.INTB
pcib0: slot 31 INTB hardwired to IRQ 17
found-> vendor=0x8086, dev=0x27da, revid=0x01
domain=0, bus=0, slot=31, func=3
class=0c-05-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=11
map[20]: type I/O Port, range 32, base 0x1100, size 5, enabled
pcib0: allocated type 4 (0x1100-0x111f) for rid 20 of pci0:0:31:3
pcib0: matched entry for 0.31.INTB
pcib0: slot 31 INTB hardwired to IRQ 17
vgapci0: <vga-compatible display="">port 0x30b0-0x30b7 mem 0xd0000000-0xd00fffff,0xc0000000-0xcfffffff irq 16 at device 2.0 on pci0
agp0: <intel 946gz="" svga="" controller="">on vgapci0
pcib0: allocated type 3 (0xd0100000-0xd0100fff) for rid 64 of agp0
agp0: Allocated flush page phys 0xd0100000 virt 0xfffff800d0100000
agp0: aperture size is 256M, detected 7676k stolen memory
agp0: AGP_I965_PGTBL_CTL2: 00000000
agp0: AGP_I855_GCC1: 0x30
agp0: AGP_I965_MSAC: 0x00
agp0: Mappable GTT entries: 65536
agp0: Total GTT entries: 131072
vgapci0: Boot video device
pcib1: <acpi pci-pci="" bridge="">irq 16 at device 28.0 on pci0
pcib1: domain 0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pci1: <acpi pci="" bus="">on pcib1
pci1: domain=0, physical bus=1
pcib2: <acpi pci-pci="" bridge="">irq 16 at device 28.4 on pci0
pcib2: allocating non-ISA range 0x4000-0x40ff
pcib0: allocated type 4 (0x4000-0x40ff) for rid 1c of pcib2
pcib2: allocating non-ISA range 0x4400-0x44ff
pcib0: allocated type 4 (0x4400-0x44ff) for rid 1c of pcib2
pcib2: allocating non-ISA range 0x4800-0x48ff
pcib0: allocated type 4 (0x4800-0x48ff) for rid 1c of pcib2
pcib2: allocating non-ISA range 0x4c00-0x4cff
pcib0: allocated type 4 (0x4c00-0x4cff) for rid 1c of pcib2
pcib2: failed to allocate initial memory window: 0xd0100000-0xd01fffff
pcib2: domain 0
pcib2: secondary bus 2
pcib2: subordinate bus 2
pcib2: I/O decode 0x4000-0x4fff
pcib2: special decode ISA
pci2: <acpi pci="" bus="">on pcib2
pci2: domain=0, physical bus=2
found-> vendor=0x8086, dev=0x109a, revid=0x00
domain=0, bus=2, slot=0, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type Memory, range 32, base 0xd0100000, size 17, enabled
pcib2: failed to allocate initial memory window (0xd0100000-0xd011ffff,0x20000)
pci2: pci0:2:0:0 bar 0x10 failed to allocate
map[18]: type I/O Port, range 32, base 0x4000, size 5, enabled
pcib2: allocated I/O port range (0x4000-0x401f) for rid 18 of pci0:2:0:0
pcib2: matched entry for 2.0.INTA
pcib2: slot 0 INTA hardwired to IRQ 16
em0: <intel(r) 1000="" pro="" network="" connection="" 7.4.2="">port 0x4000-0x401f irq 16 at device 0.0 on pci2
pcib0: allocated type 3 (0xd0200000-0xd02fffff) for rid 20 of pcib2
pcib2: allocated initial memory window of 0xd0200000-0xd02fffff
pcib2: allocated memory range (0xd0200000-0xd021ffff) for rid 10 of em0
em0: Lazy allocation of 0x20000 bytes rid 0x10 type 3 at 0xd0200000
em0: attempting to allocate 1 MSI vectors (1 supported)
msi: routing MSI IRQ 256 to local APIC 0 vector 51
em0: using IRQ 256 for MSI
em0: Using an MSI interrupt
em0: Setup of Shared code failed
device_attach: em0 attach returned 6
pcib3: <acpi pci-pci="" bridge="">irq 17 at device 28.5 on pci0
pcib3: allocating non-ISA range 0x5000-0x50ff
pcib0: allocated type 4 (0x5000-0x50ff) for rid 1c of pcib3
pcib3: allocating non-ISA range 0x5400-0x54ff
pcib0: allocated type 4 (0x5400-0x54ff) for rid 1c of pcib3
pcib3: allocating non-ISA range 0x5800-0x58ff
pcib0: allocated type 4 (0x5800-0x58ff) for rid 1c of pcib3
pcib3: allocating non-ISA range 0x5c00-0x5cff
pcib0: allocated type 4 (0x5c00-0x5cff) for rid 1c of pcib3
pcib3: failed to allocate initial memory window: 0xd0200000-0xd02fffff
pcib3: domain 0
pcib3: secondary bus 3
pcib3: subordinate bus 3
pcib3: I/O decode 0x5000-0x5fff
pcib3: special decode ISA
pci3: <acpi pci="" bus="">on pcib3
pci3: domain=0, physical bus=3
found-> vendor=0x8086, dev=0x109a, revid=0x00
domain=0, bus=3, slot=0, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0107, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type Memory, range 32, base 0xd0200000, size 17, enabled
pcib3: failed to allocate initial memory window (0xd0200000-0xd021ffff,0x20000)
pci3: pci0:3:0:0 bar 0x10 failed to allocate
map[18]: type I/O Port, range 32, base 0x5000, size 5, enabled
pcib3: allocated I/O port range (0x5000-0x501f) for rid 18 of pci0:3:0:0
pcib3: matched entry for 3.0.INTA
pcib3: slot 0 INTA hardwired to IRQ 17
em0: <intel(r) 1000="" pro="" network="" connection="" 7.4.2="">port 0x5000-0x501f irq 17 at device 0.0 on pci3
pcib0: allocated type 3 (0xd0300000-0xd03fffff) for rid 20 of pcib3
pcib3: allocated initial memory window of 0xd0300000-0xd03fffff
pcib3: allocated memory range (0xd0300000-0xd031ffff) for rid 10 of em0
em0: Lazy allocation of 0x20000 bytes rid 0x10 type 3 at 0xd0300000
em0: attempting to allocate 1 MSI vectors (1 supported)
msi: routing MSI IRQ 256 to local APIC 0 vector 51
em0: using IRQ 256 for MSI
em0: Using an MSI interrupt
em0: bpf attached
uhci0: <intel 82801g="" (ich7)="" usb="" controller="" usb-a="">port 0x3000-0x301f irq 16 at device 29.0 on pci0
ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 0 vector 52
usbus0 on uhci0
uhci0: usbpf: Attached
uhci1: <intel 82801g="" (ich7)="" usb="" controller="" usb-b="">port 0x3020-0x303f irq 17 at device 29.1 on pci0
ioapic0: routing intpin 17 (PCI IRQ 17) to lapic 0 vector 53
usbus1 on uhci1
uhci1: usbpf: Attached
uhci2: <intel 82801g="" (ich7)="" usb="" controller="" usb-c="">port 0x3040-0x305f irq 18 at device 29.2 on pci0
ioapic0: routing intpin 18 (PCI IRQ 18) to lapic 0 vector 54
usbus2 on uhci2
uhci2: usbpf: Attached
uhci3: <intel 82801g="" (ich7)="" usb="" controller="" usb-d="">port 0x3060-0x307f irq 19 at device 29.3 on pci0
ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 0 vector 55
usbus3 on uhci3
uhci3: usbpf: Attached
ehci0: <intel 82801gb="" r="" (ich7)="" usb="" 2.0="" controller="">mem 0xd0500000-0xd05003ff irq 16 at device 29.7 on pci0
usbus4: EHCI version 1.0
usbus4 on ehci0
ehci0: usbpf: Attached
pcib4: <acpi pci-pci="" bridge="">at device 30.0 on pci0
pcib4: domain 0
pcib4: secondary bus 4
pcib4: subordinate bus 4
pcib4: special decode ISA, subtractive
pci4: <acpi pci="" bus="">on pcib4
pci4: domain=0, physical bus=4
isab0: <pci-isa bridge="">at device 31.0 on pci0
isa0: <isa bus="">on isab0
ahci0: <intel ich7="" ahci="" sata="" controller="">port 0x30c8-0x30cf,0x30bc-0x30bf,0x30c0-0x30c7,0x30b8-0x30bb,0x30a0-0x30af mem 0xd0500400-0xd05007ff irq 17 at device 31.2 on pci0
ahci0: attempting to allocate 1 MSI vectors (1 supported)
msi: routing MSI IRQ 257 to local APIC 0 vector 56
ahci0: using IRQ 257 for MSI
ahci0: AHCI v1.10 with 4 3Gbps ports, Port Multiplier not supported
ahci0: Caps: 64bit NCQ ALP AL CLO 3Gbps PMD SSC PSC 32cmd 4ports
ahcich0: <ahci channel="">at channel 0 on ahci0
ahcich0: Caps: HPCP
ahcich1: <ahci channel="">at channel 1 on ahci0
ahcich1: Caps: HPCP
ahcich2: <ahci channel="">at channel 2 on ahci0
ahcich2: Caps: HPCP
ahcich3: <ahci channel="">at channel 3 on ahci0
ahcich3: Caps: HPCP
pci0: <serial bus,="" smbus="">at device 31.3 (no driver attached)
acpi_button0: <power button="">on acpi0
atkbdc0: <keyboard controller="" (i8042)="">port 0x60,0x64 irq 1 on acpi0
atkbd0: <at keyboard="">irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0xffffffff (1)
atkbd: failed to reset the keyboard.
kbd0 at atkbd0
kbd0: atkbd0, AT 84 (1), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 0 vector 57
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
psmcpnp0: <ps 2="" mouse="" port="">irq 12 on acpi0
psm0: current command byte:0067
psm0: failed to reset the aux device.
fdc0: <floppy drive="" controller="">port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: ic_type 90 part_id 80
ioapic0: routing intpin 6 (ISA IRQ 6) to lapic 0 vector 58
acpi0: wakeup code va 0xfffffe0045d8c000 pa 0x94000
ahc_isa_identify 0: ioport 0xc00 alloc failed
ahc_isa_identify 1: ioport 0x1c00 alloc failed
ahc_isa_identify 2: ioport 0x2c00 alloc failed
ahc_isa_identify 3: ioport 0x3c00 alloc failed
ahc_isa_identify 4: ioport 0x4c00 alloc failed
ahc_isa_identify 5: ioport 0x5c00 alloc failed
ahc_isa_identify 6: ioport 0x6c00 alloc failed
ahc_isa_identify 7: ioport 0x7c00 alloc failed
ahc_isa_identify 8: ioport 0x8c00 alloc failed
ahc_isa_identify 9: ioport 0x9c00 alloc failed
ahc_isa_identify 10: ioport 0xac00 alloc failed
ahc_isa_identify 11: ioport 0xbc00 alloc failed
ahc_isa_identify 12: ioport 0xcc00 alloc failed
ahc_isa_identify 13: ioport 0xdc00 alloc failed
ahc_isa_identify 14: ioport 0xec00 alloc failed
ex_isa_identify()
pcib0: allocated type 3 (0xa0000-0xa07ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa0800-0xa0fff) for rid 0 of orm0
pcib0: allocated type 3 (0xa1000-0xa17ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa1800-0xa1fff) for rid 0 of orm0
pcib0: allocated type 3 (0xa2000-0xa27ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa2800-0xa2fff) for rid 0 of orm0
pcib0: allocated type 3 (0xa3000-0xa37ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa3800-0xa3fff) for rid 0 of orm0
pcib0: allocated type 3 (0xa4000-0xa47ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa4800-0xa4fff) for rid 0 of orm0
pcib0: allocated type 3 (0xa5000-0xa57ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa5800-0xa5fff) for rid 0 of orm0
pcib0: allocated type 3 (0xa6000-0xa67ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa6800-0xa6fff) for rid 0 of orm0
pcib0: allocated type 3 (0xa7000-0xa77ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa7800-0xa7fff) for rid 0 of orm0
pcib0: allocated type 3 (0xa8000-0xa87ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa8800-0xa8fff) for rid 0 of orm0
pcib0: allocated type 3 (0xa9000-0xa97ff) for rid 0 of orm0
pcib0: allocated type 3 (0xa9800-0xa9fff) for rid 0 of orm0
pcib0: allocated type 3 (0xaa000-0xaa7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xaa800-0xaafff) for rid 0 of orm0
pcib0: allocated type 3 (0xab000-0xab7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xab800-0xabfff) for rid 0 of orm0
pcib0: allocated type 3 (0xac000-0xac7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xac800-0xacfff) for rid 0 of orm0
pcib0: allocated type 3 (0xad000-0xad7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xad800-0xadfff) for rid 0 of orm0
pcib0: allocated type 3 (0xae000-0xae7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xae800-0xaefff) for rid 0 of orm0
pcib0: allocated type 3 (0xaf000-0xaf7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xaf800-0xaffff) for rid 0 of orm0
pcib0: allocated type 3 (0xb0000-0xb07ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb0800-0xb0fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb1000-0xb17ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb1800-0xb1fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb2000-0xb27ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb2800-0xb2fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb3000-0xb37ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb3800-0xb3fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb4000-0xb47ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb4800-0xb4fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb5000-0xb57ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb5800-0xb5fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb6000-0xb67ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb6800-0xb6fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb7000-0xb77ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb7800-0xb7fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb8000-0xb87ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb8800-0xb8fff) for rid 0 of orm0
pcib0: allocated type 3 (0xb9000-0xb97ff) for rid 0 of orm0
pcib0: allocated type 3 (0xb9800-0xb9fff) for rid 0 of orm0
pcib0: allocated type 3 (0xba000-0xba7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xba800-0xbafff) for rid 0 of orm0
pcib0: allocated type 3 (0xbb000-0xbb7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xbb800-0xbbfff) for rid 0 of orm0
pcib0: allocated type 3 (0xbc000-0xbc7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xbc800-0xbcfff) for rid 0 of orm0
pcib0: allocated type 3 (0xbd000-0xbd7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xbd800-0xbdfff) for rid 0 of orm0
pcib0: allocated type 3 (0xbe000-0xbe7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xbe800-0xbefff) for rid 0 of orm0
pcib0: allocated type 3 (0xbf000-0xbf7ff) for rid 0 of orm0
pcib0: allocated type 3 (0xbf800-0xbffff) for rid 0 of orm0
pcib0: allocated type 3 (0xd0000-0xd07ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd0800-0xd0fff) for rid 2 of orm0
pcib0: allocated type 3 (0xd1000-0xd17ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd1800-0xd1fff) for rid 2 of orm0
pcib0: allocated type 3 (0xd2000-0xd27ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd2800-0xd2fff) for rid 2 of orm0
pcib0: allocated type 3 (0xd3000-0xd37ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd3800-0xd3fff) for rid 2 of orm0
pcib0: allocated type 3 (0xd4000-0xd47ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd4800-0xd4fff) for rid 2 of orm0
pcib0: allocated type 3 (0xd5000-0xd57ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd5800-0xd5fff) for rid 2 of orm0
pcib0: allocated type 3 (0xd6000-0xd67ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd6800-0xd6fff) for rid 2 of orm0
pcib0: allocated type 3 (0xd7000-0xd77ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd7800-0xd7fff) for rid 2 of orm0
pcib0: allocated type 3 (0xd8000-0xd87ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd8800-0xd8fff) for rid 2 of orm0
pcib0: allocated type 3 (0xd9000-0xd97ff) for rid 2 of orm0
pcib0: allocated type 3 (0xd9800-0xd9fff) for rid 2 of orm0
pcib0: allocated type 3 (0xda000-0xda7ff) for rid 2 of orm0
pcib0: allocated type 3 (0xda800-0xdafff) for rid 2 of orm0
pcib0: allocated type 3 (0xdb000-0xdb7ff) for rid 2 of orm0
pcib0: allocated type 3 (0xdb800-0xdbfff) for rid 2 of orm0
pcib0: allocated type 3 (0xdc000-0xdc7ff) for rid 2 of orm0
pcib0: allocated type 3 (0xdc800-0xdcfff) for rid 2 of orm0
pcib0: allocated type 3 (0xdd000-0xdd7ff) for rid 2 of orm0
pcib0: allocated type 3 (0xdd800-0xddfff) for rid 2 of orm0
pcib0: allocated type 3 (0xde000-0xde7ff) for rid 2 of orm0
pcib0: allocated type 3 (0xde800-0xdefff) for rid 2 of orm0
pcib0: allocated type 3 (0xdf000-0xdf7ff) for rid 2 of orm0
pcib0: allocated type 3 (0xdf800-0xdffff) for rid 2 of orm0
pcib0: allocated type 3 (0xe0000-0xe07ff) for rid 2 of orm0
pcib0: allocated type 3 (0xe0800-0xe0fff) for rid 2 of orm0
pcib0: allocated type 3 (0xe1000-0xe17ff) for rid 2 of orm0
pcib0: allocated type 3 (0xe1800-0xe1fff) for rid 2 of orm0
pcib0: allocated type 3 (0xe2000-0xe27ff) for rid 2 of orm0
pcib0: allocated type 3 (0xe2800-0xe2fff) for rid 2 of orm0
pcib0: allocated type 3 (0xe3000-0xe37ff) for rid 2 of orm0
pcib0: allocated type 3 (0xe3800-0xe3fff) for rid 2 of orm0
isa_probe_children: disabling PnP devices
atkbdc: atkbdc0 already exists; skipping it
atrtc: atrtc0 already exists; skipping it
attimer: attimer0 already exists; skipping it
fdc: fdc0 already exists; skipping it
sc: sc0 already exists; skipping it
isa_probe_children: probing non-PnP devices
orm0: <isa option="" roms="">at iomem 0xc0000-0xcafff,0xcb000-0xcbfff on isa0
sc0: <system console="">at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
pcib0: allocated type 4 (0x3c0-0x3df) for rid 0 of vga0
pcib0: allocated type 3 (0xa0000-0xbffff) for rid 0 of vga0
ppc0: cannot reserve I/O port range
ppc0 failed to probe at irq 7 on isa0
pcib0: allocated type 4 (0x3f8-0x3ff) for rid 0 of uart0
uart0 failed to probe at port 0x3f8-0x3ff irq 4 on isa0
pcib0: allocated type 4 (0x2f8-0x2ff) for rid 0 of uart1
uart1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
wbwd0 failed to probe on isa0
isa_probe_children: probing PnP devices
est0: enabling SpeedStep
est0: <enhanced speedstep="" frequency="" control="">on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr b200b2006000b20
device_attach: est0 attach returned 6
p4tcc0: <cpu frequency="" thermal="" control="">on cpu0
est1: <enhanced speedstep="" frequency="" control="">on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr b200b2006000b20
device_attach: est1 attach returned 6
p4tcc1: <cpu frequency="" thermal="" control="">on cpu1
Device configuration finished.
procfs registered
lapic: Divisor 2, Frequency 99752152 Hz
Timecounters tick every 1.000 msec
pflog0: bpf attached
crypto: <crypto device="">vlan: initialized, using hash tables with chaining
tcp_init: net.inet.tcp.tcbhashsize auto tuned to 32768
IPsec: Initialized Security Association Processing.
pfsync0: bpf attached
lo0: bpf attached
enc0: bpf attached
hpt27xx: no controller detected.
hptrr: no controller detected.
hptnr: no controller detected.
random: unblocking device.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0
ahcich0: AHCI reset…
ahcich0: SATA connect time=900us status=00000113
ahcich0: AHCI reset: device found
ahcich1: AHCI reset...
ahcich1: SATA offline status=00000004
ahcich1: AHCI reset: device not found
ahcich2: AHCI reset...
ugen1.1: <intel>at usbus1
uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
ugen0.1: <intel>at usbus0
uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
ugen3.1: <intel>at usbus3
uhub2: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
ugen2.1: <intel>at usbus2
uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus2
ugen4.1: <intel>at usbus4
uhub4: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus4
ahcich2: SATA connect time=900us status=00000113
ahcich2: AHCI reset: device found
ahcich2: AHCI reset: device ready after 0ms
ahcich3: AHCI reset...
ahcich3: SATA offline status=00000004
ahcich3: AHCI reset: device not found
ahcich0: AHCI reset: device ready after 100ms
pass0 at ahcich0 bus 0 scbus0 target 0 lun 0
GEOM: new disk cd0
cd0 at ahcich2 bus 0 scbus2 target 0 lun 0
cd0: <tsstcorp cddvdw="" ts-h653n="" 0208="">Removable CD-ROM SCSI-0 device
cd0: 150.000MB/s transfers (SATA 1.x, UDMA2, ATAPI 12bytes, PIO 8192bytes)
cd0: Attempt to query device size failed: NOT READY, Medium not present - tray closed
pass0: <st3250310as 3.aaf="">ATA-7 SATA 1.x device
pass0: Serial Number 6RYAJH0Y
pass0: 150.000MB/s transfers (SATA 1.x, UDMA6, PIO 8192bytes)
pass0: Command Queueing enabled
pass1 at ahcich2 bus 0 scbus2 target 0 lun 0
pass1: <tsstcorp cddvdw="" ts-h653n="" 0208="">Removable CD-ROM SCSI-0 device
pass1: 150.000MB/s transfers (SATA 1.x, UDMA2, ATAPI 12bytes, PIO 8192bytes)
ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
ada0: <st3250310as 3.aaf="">ATA-7 SATA 1.x device
ada0: Serial Number 6RYAJH0Y
ada0: 150.000MB/s transfers (SATA 1.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 238475MB (488397168 512 byte sectors: 16H 63S/T 16383C)
ada0: Previously was known as ad4
GEOM: new disk ada0
Netvsc initializing... done!
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x01000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 1 vector 48
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 1 vector 49
ioapic0: routing intpin 17 (PCI IRQ 17) to lapic 1 vector 50
ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 1 vector 51
msi: Assigning MSI IRQ 257 to local APIC 1 vector 52
SMP: passed TSC synchronization test
TSC timecounter discards lower 1 bit(s)
Timecounter "TSC-low" frequency 1097273336 Hz quality 1000
Root mount waiting for: usbus4 usbus3 usbus2 usbus1 usbus0
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
Root mount waiting for: usbus4
Root mount waiting for: usbus4
uhub4: 8 ports with 8 removable, self powered
Root mount waiting for: usbus4
Trying to mount root from ufs:/dev/ada0s1a [rw]…
start_init: trying /sbin/init
ugen0.2: <microsoft>at usbus0
ukbd0: <microsoft 0="" 2="" natural="" ergonomic="" keyboard="" 4000,="" class="" 0,="" rev="" 2.00="" 1.73,="" addr="">on usbus0
kbd2 at ukbd0
kbd2: ukbd0, generic (0), config:0x0, flags:0x3d0000
uhid0: <microsoft 0="" 2="" natural="" ergonomic="" keyboard="" 4000,="" class="" 0,="" rev="" 2.00="" 1.73,="" addr="">on usbus0
ugen3.2: <crystalfontz america="">at usbus3
umodem0: <crystalfontz 2="" america="" cfa-735="" display,="" class="" 0,="" rev="" 2.00="" 2.00,="" addr="">on usbus3
umodem0: data interface 1, has no CM over data, has no break
em0: Link is up 1000 Mbps Full Duplex
ugen4.2: <vendor 0x0409="">at usbus4
uhub5: <vendor 2="" 9="" 0x0409="" product="" 0x005a,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus4
uhub5: 4 ports with 4 removable, self powered
ugen4.3: <vendor 0x0b95="">at usbus4
axe0: <vendor 3="" 0x0b95="" product="" 0x7720,="" rev="" 2.00="" 0.01,="" addr="">on usbus4
axe0: PHYADDR 0xe0:0x10
miibus0: <mii bus="">on axe0
ukphy0: <generic ieee="" 802.3u="" media="" interface="">PHY 16 on miibus0
ukphy0: OUI 0x007063, model 0x0001, rev. 1
ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ue0: <usb ethernet="">on axe0
ue0: bpf attached
coretemp0: <cpu on-die="" thermal="" sensors="">on cpu0
coretemp0: Setting TjMax=85
est0: <enhanced speedstep="" frequency="" control="">on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr b200b2006000b20
device_attach: est0 attach returned 6
coretemp1: <cpu on-die="" thermal="" sensors="">on cpu1
coretemp1: Setting TjMax=85
est1: <enhanced speedstep="" frequency="" control="">on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr b200b2006000b20
device_attach: est1 attach returned 6
em0: Link is Down
em0: Link is up 1000 Mbps Full Duplex
em0: link state changed to UP
pflog0: promiscuous mode enabled
em0: promiscuous mode enabled
ue0: promiscuous mode enabled
[2.2-RC]</enhanced></cpu></enhanced></cpu></usb></generic></mii></vendor></vendor></vendor></vendor></crystalfontz></crystalfontz></microsoft></microsoft></microsoft></st3250310as></tsstcorp></st3250310as></tsstcorp></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></crypto></cpu></enhanced></cpu></enhanced></generic></system></isa></floppy></ps></at></keyboard></power></serial></ahci></ahci></ahci></ahci></intel></isa></pci-isa></acpi></acpi></intel></intel></intel></intel></intel></intel(r)></acpi></acpi></intel(r)></acpi></acpi></acpi></acpi></intel></vga-compatible></acpi></acpi></at></at></acpi></acpi></ptltd ></software></memory>_</crypto></software,></software,></null></version></ptltd ></lahf></syscall,lm></sse3,dtes64,mon,ds_cpl,est,tm2,ssse3,cx16,xtpr,pdcm></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe> -
You won't see em5 because you only have two em interfaces. The box I was using for a test has 6 em NICs. em5 wasn't being used so I ran the test on it in case it broke the interface for whatever reason.
I don't see the rom dump output from your onboard NICs?In your first verbose boot log both em NICs are recognised and attached. Did you do anything other than boot verbose?
There's nothing obvious to help diagnose this though.
Steve
-
I did those commands for rom dump and it did same result you seen after you entered it.. Although I used only em0 and em1. I looked in system log in UI and nothing and then dmesg and seen nothing either. I am not sure where it put the dump at
-
The actual dumped data appears in the system log. You can access that from the webgui or using 'dmesg' at the command line.
Steve
-
Well I tried again and noticed when using ssh and doing sysctl dev.em.0.nvm=1 I had something appear on my monitor that is on the pfsense firewall. Here is what i seen.. see picture
![2014-12-15 20.50.11.jpg](/public/imported_attachments/1/2014-12-15 20.50.11.jpg)
![2014-12-15 20.50.11.jpg_thumb](/public/imported_attachments/1/2014-12-15 20.50.11.jpg_thumb)