Multi-WAN gateway failover not switching back to tier 1 gw after back online
-
Well you need to fix your DNS. Sounds like it might not be working right on one or both WANs. Are you using the forwarder or the resolver?
It shouldn't matter which WAN the resolver uses because it should only be trying to talk to authoritative name servers that should accept queries from everywhere.
The problem lies in forwarders because you usually point the forwarder at ISP caching servers and they might only accept connections from their network so it matters which DNS servers are used out which interface.
I tried both the resolver and the forwarder, some sites are just not resolved. Unfortunately I don't think I can use pfsense in a production environment, for me at least failover it's not working with pppoe :(.
should "State Killing on Gateway Failure" should be on?
Thanks
-
Depends on whether or not you want states killed on a gateway failure.
-
Depends on whether or not you want states killed on a gateway failure.
Well, isn't better to have them reset on a gw failure? The definition is a bit tricky for this option
-
I only skimmed through this thread so I apologize if this was already suggested but – are you certain your clients are set to use the pfSense IP as their DNS resolver? If e.g. you have a gateway defined with a custom monitor IP of 8.8.8.8 or the DNS servers on your General settings page are locked to a specific gateway, then static routes are built which will force traffic out that specific gateway, even if it's down. So this could result in DNS being "dead" when one of the gateways goes down. Is this possibly what's happening?
-
I only skimmed through this thread so I apologize if this was already suggested but – are you certain your clients are set to use the pfSense IP as their DNS resolver? If e.g. you have a gateway defined with a custom monitor IP of 8.8.8.8 or the DNS servers on your General settings page are locked to a specific gateway, then static routes are built which will force traffic out that specific gateway, even if it's down. So this could result in DNS being "dead" when one of the gateways goes down. Is this possibly what's happening?
Monitor IPs are currently set to one of each ISP, in General I have a pair of DNSes set for each gateway (four servers in total). Clients DNS is manullay set 192.168.1.1 (pfsense)
-
I tried both the resolver and the forwarder, some sites are just not resolved.
If you do not know how to get more information than that about what's actually happening, you are probably in over your head.
-
I tried both the resolver and the forwarder, some sites are just not resolved.
If you do not know how to get more information than that about what's actually happening, you are probably in over your head.
Oh, nice. What can I say?Thanks? :)…..Thanks.
-
Hi
yanakis, in my case we have the fiber media converter and the router (not PPPoE), and happens the same. I switched off or disconnected the router, but never tried switching off media converter (good idea).
In my last installations I don't usually use DNS forwarder/resolver for localhost, but in this case I do (I configured it in the past and never change it). Have you tried deactivating that option in General Settings? Just to see if something changes.
I understand luckman212 concerns about DNS and static routes created by pfsense for each DNS associated to a wan, but in my case we had two different DNS configured and working, and failed. And in any case, once wan is recovered again, DNS works again and everything should work again.
By the way, I tried with "State Killing on Gateway Failure" on and off, and recover fails in both cases. I keep it unchecked, because with external sip connections is mandatory to make failover work (at least in my case). And I personally prefer to reset states if a gateway fails, to avoid problems.
Regards
PD: I don't think you are in over your head… Thanks for all
-
Hi
yanakis, in my case we have the fiber media converter and the router (not PPPoE), and happens the same. I switched off or disconnected the router, but never tried switching off media converter (good idea).
In my last installations I don't usually use DNS forwarder/resolver for localhost, but in this case I do (I configured it in the past and never change it). Have you tried deactivating that option in General Settings? Just to see if something changes.
I understand luckman212 concerns about DNS and static routes created by pfsense for each DNS associated to a wan, but in my case we had two different DNS configured and working, and failed. And in any case, once wan is recovered again, DNS works again and everything should work again.
By the way, I tried with "State Killing on Gateway Failure" on and off, and recover fails in both cases. I keep it unchecked, because with external sip connections is mandatory to make failover work (at least in my case). And I personally prefer to reset states if a gateway fails, to avoid problems.
Regards
PD: I don't think you are in over your head… Thanks for all
Well, I left empty the DNS fields in General but failback to WAN still not working after WAN recovery unless I change something in Firewall or Routing and apply changes :(
-
…and this looks like a pfsense problem...
I cannot second that!
I have this working for quite some time now with WAN1 (100Mb cable) and a rather old WAN2 (6Mb DSL).
I have failover to W2 if W1 is down and immediately W1 again when available.Show us your System | Routing | Gateway Groups page.
Hi Cris. Can you please post your setup? Thanks
-
Well, Derelict wrote that my config seems to be a bit more complicated than necessary.
Since I trust him I usually would test his suggestion first and post afterwards. I just don't have the time for that in the foreseeable future…I only use DSL as failover (it's 6Mbit) and rely on cable which is 100Mbit.
You will know why if you have teen kids...
Just checked and failover to DSL is working as well as fallback to cable when available again.I set this up about a year ago and used the pfsense docs for that.
-
I have mine set up exactly like you do (A group with Tier 1 Cable, Tier 2 DSL and a group with Tier 1 DSL, Tier 2 Cable).
I was just commenting it's only necessary if you want to have rules that prefer the other circuit while maintaining the ability for those rules to fail over too.
I tested my failover yesterday since I was putting new splitters on my cable in anticipation of MoCA 2.0. It all worked exactly as configured and when I was done it brought my Tier 1 back online just as it has many times before.
-
i didn't criticize! I only mentioned that I might be done with half the work. ;)
-
Hi again
Past week we've installed a new machine with 2.2.4 and two WAN with failover, and same problem. In this case we have to different LANs, and each one has one failover group with different order (one with wan1->wan2 and the other with wan2->wan1), and none of them redirect traffic to the main one when it's recovered (we have to do some change and Save, as yanakis says).
It's a new installation without anything strange. We run several tests in both directions, and I can confirm the problem exists. Never went back automatically to the recovered main wan.
We didn't find nothing new or more clues, it just doesn't work.
Regards
-
+1 with arcanos.
In fact, instead of attempting to troubleshoot this and failing, it would be better if someone that has this working, would post a complete series of screenshots showing their setup. Then we can all learn from a working environment.
-
Is PPPoE a common factor for those that don't work? Both my WANs are DHCP.
There's really nothing to it. Create a gateway group with a Tier 1 and Tier 2 with member down as the trigger level and policy route to it.
-
Correct, PPPoE is the default and DHCP is the failover.
-
Not PPPoE in my case. This last case are two cable connections with routers with NAT and DMZ pointing to the wan interface of pfsense. But I've seen the problem with DSL and cable in bridge mode.
-
On the first view I have the same issue but looking deeper I can see that my Gateway keeps really offline until I reapply the interface config page or reboot.
Short decription of config and behavior:
I have two gateways (1. fiber / 2. cable modem) with a routing group for balancing (tier 1 / tier 1). Both gateways are monitored against external DNS servers. The routing group is defined as gateway in FW rule. "Use sticky connection" on System-advanced-misc. is on.
At the beginning after reboot all works fine an traffic is distributed to both gateways with weight 1:4.
But after some minutes / hours always second gateway goes offline (100% package loss) and keeps this status until I reapply the interface config or reboot. It's not an apinger problem. The gateway is really broken. A ping from Diagnostic - ping with source of gateway doesn't work (100% loss). The cable modem isn't disconnect and it works if a plugin a notebook there. So Pfsense stops the gateway really and keep it broken. Even if I disconnect the lan wire and reconnect no reaction.
Same happens on my backup Pfsense which is running in CARP mode. There is no traffic load but GW stops also.
If I set routing group in redundant mode (GW 1 tier 1 / GW 2 tier 2 OR GW 2 tier 1 / GW 1 tier 2) then all work OK. The gateways keep online. Also after reconnection of wire the interface comes online again.
My estimation is that there must be something wrong with balancing gateways. But I need the capacity of both gateways.
-
you should put a working monitor ip for each interfaces like dns ip
