2.2.4 and how I enabled TRIM
-
–---- I was pretty frustrated getting TRIM enabled in 2.2.4
------ This is what worked for me to get the trim status set to enabled for my SSD.
1. booted pfSense from USB stick and installed pfSense to SSD
2. booted pfSense from SSD and watched my console -- made note of ...
"Trying to mount root from /dev/ufsid/55bdd213616a70a3"3. booted pfSense from USB stick into single-user mode
4. at the # prompt, the following was issued:
/sbin/tunefs -t enable /dev/ufsid/55bdd213616a70a3
/sbin/reboot5. booted pfSense from SSD. ran Shell from the console -- verified TRIM status with:
/sbin/tunefs -p /------ I hope this works for everyone!
-
Hmmm…
'tunefs -p /' shows TRIM enabled for me, and I didn't do anything to enable it:
[2.2.4-RELEASE][nicholfd@burns.springfield.com]/root: tunefs -p / tunefs: POSIX.1e ACLs: (-a) disabled tunefs: NFSv4 ACLs: (-N) disabled tunefs: MAC multilabel: (-l) disabled tunefs: soft updates: (-n) enabled tunefs: soft update journaling: (-j) enabled tunefs: gjournal: (-J) disabled tunefs: trim: (-t) enabled tunefs: maximum blocks per file in a cylinder group: (-e) 4096 tunefs: average file size: (-f) 16384 tunefs: average number of files in a directory: (-s) 64 tunefs: minimum percentage of free space: (-m) 8% tunefs: space to hold for metadata blocks: (-k) 6408 tunefs: optimization preference: (-o) time tunefs: volume label: (-L)
-
Since my installation was a new one, from scratch, I had the luxury of checking for the enabled flag .. and once seeing it was not enabled I simply re-installed with the same result.
It appears that some installs, apparently get the flag set, while others do not –- in my case it was not set so I figured out a solution.
But, hey ... still love pfSense nonetheless --- great software.
-
Devices purchased from the pfSense store are loaded with TRIM enabled since we know the hardware and disks are capable (or at least in some cases do not have a negative reaction to it). We can't be sure of that everywhere so it isn't enabled in the normal installer. Eventually it may find its way into the install process, we're really eager to ditch the current installer and move to something newer.
-
–---- I was pretty frustrated getting TRIM enabled in 2.2.4
Why? The pfsense team is not able to see or expect the hardware we all are using everywhere!
Only their own units from the pfSense Shop they are knowing well, but anyway, if you buy a SG-xxxx
unit from them, without a SSD or mSATA device and then you are installing one after some time
by your own willing and the SSD or mSATA is not capable of TRIM support, but this will be activated
automatically by the pfSense OS the device will be perhaps harmed or destroyed.–---- This is what worked for me to get the trim status set to enabled for my SSD.
This is much more better as I see it right.
You buy a device such as a SSD, mSATA, SATA-DOM, SSD-DOM or PCIe-SSD and only you are knowing
if this device is 100% capable of TRIM support and only you will be responsible for the activating or not.For sure and it depends on thinking after a fresh and full install on a mSATA I was also imagine that should be
a so called "must be" that TRIM support is activated after the installation was finished. But what you think I
would wrote you all today if the will be true but on the other side the mSATA was not capable of TRIM
support? -
–---- I was pretty frustrated getting TRIM enabled in 2.2.4
------ This is what worked for me to get the trim status set to enabled for my SSD.
3. booted pfSense from USB stick into single-user modeI had my first SSD failure (3 years old) and was pretty frustrated getting TRIM set too. I thought I had remembered something in the build up to 2.2 propaganda that this feature was going to be a tick box so I looked all over and couldn't find it… tried the old ways, didn't work... your booting into single-user mode was the trick.
thanks,
Rick -
When will fstrim be a part of pfsense (not as a addon)?
-
I second the notion that it would indeed be a great idea to add this option in the installer as a tick box. I also had issues getting it enabled a few versions back, and the single user mode worked. I also had a question regarding pfsense's software RAID mirroring and TRIM. Is it possible on two supported SSD's and how would it be accomplished?
-
It's STILL not there even in 2.3?! There was something even available at certain time to avoid similar absurd hacking around, then it got removed with a commit message "we'll figure out something better" so it went MIA in 2.2.x and and nothing ever came back.
Seriously absurd.
-
indeed be a great idea to add this option in the installer as a tick box.
and
I also had issues getting it enabled a few versions back, and the single user mode worked
Would be the problem as I see it right.
message "we'll figure out something better" so it went MIA in 2.2.x and nothing ever came back.
At this time I really think it might be the best to be able to activate it manual by the admin is much better then
all other things, because from where the developer would be able to know if this or another SSD is really
capable of TRIM support? Many peoples are often here in the forum are asking for a so called "cheap build"
and then many of them tend also to take a cheap SSD or mSATA to go with and don´t really know anything
about the TRIM support of this devices. And if there will be an automatic enabled TRIM support and a device
will be down or failing all peoples will complain to the developer team about this service, so if you know what
kind of SSD or mSATA you are running you could be activating it on the manual way better then the automatic
way, that will be often beloved to have and called for. -
Do you happen to know if (on two SSD's that supported TRIM of course) a softraid mirror that the newer version offers during install, is also possible with TRIM enabled on both drives?
-
I've been looking for answers to this for a while now. I thought I had it right that each of the SSD drives have to be partitioned, formatted and offset before the PF sense install/config. Then trim would be set post-install presuming its Raid-1 compatible. But after reading this post about a softraid miror, i'm not so sure.
Re: https://forum.pfsense.org/index.php?topic=99424.msg556454
-
For my purposes, and as is mentioned by Jimp in that threat you're quoting, a new softraid array, and a simple config backup and restore would be the much more supported and easier way to go. I would think trying hardware raid would much more challenging. If pfsense supports a mirrored softraid option and auto handles all the partitioning / drive formatting on it's own, why mess with a controller? It's also got email alerts for array status baked in already. I imagine some people have certain use cases where hardware RAID would somehow be better but for my purposes I can't think of one. Adding a controller card still creates a single point of failure, just like softraid and a motherboard failure is a single point of failure. It's not like there's a ton of data on pfsense installations and data loss is more important than uptime right? but can TRIM be enabled on pfsense's OWN softraid mirroring is the answer am I after. I imagine setting trim for something with a controller would be an entirely different story altogether.
What I'm saying is, all of those things you're mentioning doing prior to a pfsense softraid install, don't need to be done. It's done during install now if it detects two (or more I would guess) identical disks and does a softraid mirror for you. Can TRIM be added to these drives after "the easy way" of doing softraid with pfsense?
-
I'm not hung up on needing a hardware raid solution. And just to be clear I'm NOT intending to image my SSD to a pair of SSD's as an upgrade path. I just want to know what works in a holistic manner. I know SSDs need to be offset. I know raid and trim need to be compatible. But need a stepped process to upgrade from one SSD to a raided pair of SSD's while retaining an offset & trim like my current single drive full install has. Has nobody successfully accomplished this yet? Maybe I'll have to poney up for another box that's non-production I can tinker with.
-
I think we're saying the same thing. Although I don't quite get the offset bit. This is something that pfsense does not do by default when installed on an SSD normally? I'm looking to do the exact same thing you are. Migrate form a single SSD to a mirrored RAID SSD, and have TRIM enabled. I have TRIM enabled on the one I use now, but I never did anything outside of that, or out of the usual pfsense install sequence. Am I missing something?
-
I think so, we're after the same. According to Jimp on my reference post he said two months ago, "There is no special code in the installer to handle any sort of alignment/offset at this time". WinXp doesnt but Win8 does offset when an SSD is detected. Presume FreeBsd doesn't by default. SSD performance can be substantially reduced if its partition is not properly offset. So I figure I have to partition, format & offset the new SSD pair with partition magic or other self-booting drive utility cd then install PfSense.
-
It would surprise me that so many users of things like FreeNAS would have a storage based OS designed around something that didn't handle drive partitioning for almost any drive properly by default. Very interested in the response from someone from pfsense on this. So I guess my questions have expanded now to : :D
1. Does pfsense not using this mentioned type of partition offset actually adversely affect SSD life? how much? As much as something like not enabling TRIM?
(I see a few people randomly asking about this in the forums, but never heard it was some type of precaution needed when using pfsense (BSD) with an SSD, then again, I'm not super familiar with BSD outside of pfsense)2. Is doing a softraid mirror with SSD's in pfsense and TRIM a viable option?
-
–---- I was pretty frustrated getting TRIM enabled in 2.2.4
------ This is what worked for me to get the trim status set to enabled for my SSD.
1. booted pfSense from USB stick and installed pfSense to SSD
2. booted pfSense from SSD and watched my console -- made note of ...
"Trying to mount root from /dev/ufsid/55bdd213616a70a3"3. booted pfSense from USB stick into single-user mode
4. at the # prompt, the following was issued:
/sbin/tunefs -t enable /dev/ufsid/55bdd213616a70a3
/sbin/reboot5. booted pfSense from SSD. ran Shell from the console -- verified TRIM status with:
/sbin/tunefs -p /------ I hope this works for everyone!
I'm running a fresh install of 2.2.5 on a TRIM capable SSD. My system details are in my sig.
I just performed a clean install too and used the auto restore method to bring my config.xml file settings back. Didn't have to do this but since I have holiday time off I had some time to experiment, wanted to learn something new, and thought maybe after so many upgrades some 'dirt' might have been left behind. I can't get TRIM to work at all. Granted, I don't know anything when it comes to CLI in pfSense. I checked, and TRIM is not enabled.
I login in under single user mode, I tried just the basic commands
/sbin/tunefs -t enable / (this errors and I get "cannot execute, no such file/directory")
/sbin/reboot (this doesn't work at all but just typing EXIT does)I took note of TRYING TO MOUNT details using DMESG under command prompt in WEBGUI.
So I tried
/sbin/tunefs -t enable /dev/ufsid/56534606bb206e02
and again NO SUCH FILE/DIRECTORY error message.At this point I am stumped.
Anyone have any advice? This is really more about me learning and understanding this TRIM problem than it is turning it on…so please help me learn when providing the solution with some explanation. Thanks in advance!
PS - to the pfSense developers...2.3...Bootstrap....WOW!!!!!!!!!!!!!!!! Those screenshots are just amazing! I can't wait!
-
This worked for me in 2.2.5. Thank you kindly for sharing this ThePOO!
-
I login in under single user mode, I tried just the basic commands
/sbin/tunefs -t enable / (this errors and I get "cannot execute, no such file/directory")
/sbin/reboot (this doesn't work at all but just typing EXIT does)I took note of TRYING TO MOUNT details using DMESG under command prompt in WEBGUI.
So I tried
/sbin/tunefs -t enable /dev/ufsid/56534606bb206e02
and again NO SUCH FILE/DIRECTORY error message.At this point I am stumped.
Your problem is, for some reason, running the commands. tunefs is not even trying to access /dev/ufsid/56534606bb206e02 since it failed to run.