PfBlockerNG v2.0 w/DNSBL

[BBcan177]

@Nachtfalke:

shExpMatch(host, "10.123.123.123") ||

Nothing changed. I deleted these file because I added the part Merchant posted in this thread:

I think you need to change that line from "host" to "url"… I believe that your desktop is the host, and the url is where you want to goto... So the DNSBL VIP is not the host, but the url... As i said, I don't use squid, so just an assumption...

shExpMatch(url, "10.123.123.123") ||

[JasonJoel]

@BBcan177:

@JasonJoel:

Anyone else experience that pfBlockerNG doesn't work on 2.3 if using floating rules?

Hi Jason,

Do you have any Floating rules above the pfBNG floating rules? Maybe send a screenshot? also edit one of those rules and send a screenshot…

The only other floating rule is the DNSBL rule, and it works I think.

I block the country China in pfBlocker. With it set to not use floating rules www.edu.cn is blocked as expected. It gets blocked, and the pfB_Top_v4 hit count increases.

If I go back and enable floating rules, the rules get made (as shown in the attached pictures), and the aliases do have IPs in them. But if I again go to www.edu.cn, it does not get blocked… I really don't get it, as the floating rule looks the same to me as the rule that gets created in the interface when not using floating rules in pfBlocker...

Pic 1 shows my floating rules when pfBlocker is set to not use floating rules.
Pic 2 shows that pfB_Top-v4 hit count increases when going to www.edu.cn, as expected
Pic 3 shows floating rules when floating rules in pfBlocker is enabled
Pic 4 shows that after trying to go to www.edu.cn again, nothing is blocked
Pic 5 shows that if I manually make the exact same rule, it DOES work... ????????

Jason


[BBcan177]

Hi Jason,

When you edit those Floating rules, do your interfaces get added correctly? Looks fine at first glance… I tested it on my machine, and all seems to be working with/without floating rules...

[JasonJoel]

@BBcan177:

Hi Jason,

When you edit those Floating rules, do your interfaces get added correctly? Looks fine at first glance… I tested it on my machine, and all seems to be working with/without floating rules...

Yes they do.

HOWEVER, I discovered the issue!! The rule direction is marked as "OUT" - which is never going to match on traffic initiated internally going to the internet. Shouldn't that be "ANY"? I checked and all of my pfBlocker created floating rules are direction "OUT" for some reason…

Screen attached.

Jason


[BBcan177]

@JasonJoel:

The rule direction is marked as "OUT". Shouldn't that be "ANY"? I checked and all of my pfBlocker created floating rules are direction "OUT" for some reason…

Did you define the "Adv. In/Outbound settings" in each pfBNG Alias settings? Specifically the "Gateway" setting?

It should normally be left at "default"; at which time, the Floating Rules "Direction" setting is set to "any".

You can run this command to find out what the pfBNG aliases gateway settings are defined as:

grep "<agateway" conf="" config.xml<="" pre=""></agateway">

[JasonJoel]

@BBcan177:

@JasonJoel:

The rule direction is marked as "OUT". Shouldn't that be "ANY"? I checked and all of my pfBlocker created floating rules are direction "OUT" for some reason…

Did you define the "Adv. In/Outbound settings"? Specifically the "Gateway" setting?

It should normally be left at "default"; at which time, the Floating Rules "Direction" setting is set to "any".

I don't think so… Here are the advanced settings on my country Top 20 alias, which gets created as OUT.

Jason


[BBcan177]

Can you save each of your pfBlockerNG aliases as I think that tag is missing from your config.

Run this command first and send me the output:

grep "<agateway" conf="" config.xml<="" pre=""></agateway">

[JasonJoel]

Where do you run the command? Should I SSH in or can I do it from the GUI?

[BBcan177]

In pfSense:  Diagnostics / Command Prompt / Execute PHP Commands

[JasonJoel]

Ran this:
grep " <agateway" conf="" config.xml<br="">Got this:
Parse error: syntax error, unexpected '"</agateway">

[BBcan177]

@JasonJoel:

Ran this:
grep " <agateway" conf="" config.xml<br="">Got this:
Parse error: syntax error, unexpected '"<agateway"' (t_constant_encapsed_string)="" in="" tmp="" r6f0tv="" on="" line="" 5<br=""></agateway"'></agateway">

Sorry, use the "Execute Shell Command" box..

[JasonJoel]

@BBcan177:

@JasonJoel:

Ran this:
grep " <agateway" conf="" config.xml<br="">Got this:
Parse error: syntax error, unexpected '"<agateway"' (t_constant_encapsed_string)="" in="" tmp="" r6f0tv="" on="" line="" 5<br=""></agateway"'></agateway">

Sorry, use the "Execute Shell Command" box..

First time I ran it, it gave me an error.

After I re-saved all of the alias it gave me:
<agateway_in>default</agateway_in>
<agateway_out>default</agateway_out>
<agateway_in>default</agateway_in>
<agateway_out>default</agateway_out>
<agateway_in>default</agateway_in>
<agateway_out>default</agateway_out>
<agateway_in>default</agateway_in>
<agateway_out>default</agateway_out>
<agateway_in>default</agateway_in>
<agateway_out>default</agateway_out>
<agateway_in>default</agateway_in>
<agateway_out>default</agateway_out>

[BBcan177]

Ok now run a "Force Update" and check your rules to see if "Any" in defined in the direction field… then check the  blocking behavior again... I will get a fix out for this tonight... Thanks for reporting...

[JasonJoel]

@BBcan177:

Ok now run a "Force Update" and check your rules to see if "Any" in defined in the direction field… then check the  blocking behavior again... I will get a fix out for this tonight... Thanks for reporting...

After doing a force update the floating rules are now "ANY" and blocking works correctly! Sorry I took so much of your time, but thank you for helping - it does seem like re-saving the alias did the trick.

Jason

[BBcan177]

The following Pull Request #121 for pfBlockerNG v2.0.12 has been Merged for pfSense v2.3 only.

This version contains an URGENT fix for anyone who uses Floating pfBlockerNG Rules!!

PR also contains other improvements (See link above).

[chris4916]

@BBcan177:

I don't use Squid, but a quick google search, do you think that "host" should be changed to "url" instead in this line below?

I know this is slightly nitpicking but it has nothing to do with Squid itself but rather the proxy.pac that will help your browser deciding whether access is direct or through proxy  ;)

This said, in proxy.pac (or whatever alias), you may look at different kind of information in order to make the "routing" decision.

If goal is to route through proxy (or not) based on IP address or DNS related information, this should implement directive like:
dnsDomainIs(host,…
isInNet(dnsResolve(host)
localHostOrDomainIs(host...

This involves DNS resolution

if goal is to look at URL pattern (not involving DNS resolution) then syntax to be used is:
shExpMatch(url,
url.substring

However, shExpMatch(host, does work  too  if you match the fqdn part of URL only 8) (although this is quite confusing, I agree)

[simby]

Hi!

i have error:

There were error(s) loading the rules: /tmp/rules.debug:40: cannot define table pfB_Malicious: Cannot allocate memory - The line in question reads [40]: table persist file "/var/db/aliastables/pfB_Malicious.txt" @ 2016-04-26 07:10:37

and i have 16GB memory on i7

What is the problem?

[cmaxwell04]

@BBcan177:

@cmaxwell04:

Help please,

I'm having a strage problem in pfsense 2.3. Whenever I enable pfBlockerNG DNSBL it stops DNS Resolver, and I have to start it manually. when I rebot pfsense 2.3 I have to manualy start DNS Resolver. if I desable DNSBL, DNS Resolver will always run automaticaly.

thanks

Hi cmaxwell04,

Can you review the pfblockerng.log and see if there are any error messages in regards to DNSBL. Try to Re-Enable DNSBL, and try to send any relevant error messages… Do you see any errors in the resolver.log or system.log?

After a reboot of the pfsense, DNS Resolver was not running, so I disabled DNSBL and got this error messages.

Notices
Filter Reload

There were error(s) loading the rules: /tmp/rules.debug:214: macro 'pfB_DNSBLIP' not defined - The line in question reads [214]: block return in log quick on $LAN inet from any to $pfB_DNSBLIP tracker 1770009088 label "USER_RULE: pfB_DNSBLIP auto rule" @ 2016-04-26 12:58:40

Crash report begins.  Anonymous machine information:

amd64
10.3-RELEASE
FreeBSD 10.3-RELEASE #4 05adf0a(RELENG_2_3_0): Mon Apr 11 19:09:19 CDT 2016    root@factory23-amd64-builder:/builder/factory-230/tmp/obj/builder/factory-230/tmp/FreeBSD-src/sys/pfSense

Crash report details:

PHP Errors:
[26-Apr-2016 12:59:13 Africa/Abidjan] PHP Stack trace:
[26-Apr-2016 12:59:13 Africa/Abidjan] PHP  1. {main}() /etc/rc.update_urltables:0
[26-Apr-2016 12:59:13 Africa/Abidjan] PHP  2. process_alias_urltable() /etc/rc.update_urltables:51
[26-Apr-2016 12:59:13 Africa/Abidjan] PHP  3. parse_aliases_file() /etc/inc/pfsense-utils.inc:2185
[26-Apr-2016 12:59:13 Africa/Abidjan] PHP  4. filesize() /etc/inc/pfsense-utils.inc:1932

[Nachtfalke]

@chris4916:

@BBcan177:

I don't use Squid, but a quick google search, do you think that "host" should be changed to "url" instead in this line below?

I know this is slightly nitpicking but it has nothing to do with Squid itself but rather the proxy.pac that will help your browser deciding whether access is direct or through proxy  ;)

This said, in proxy.pac (or whatever alias), you may look at different kind of information in order to make the "routing" decision.

If goal is to route through proxy (or not) based on IP address or DNS related information, this should implement directive like:
dnsDomainIs(host,…
isInNet(dnsResolve(host)
localHostOrDomainIs(host...

This involves DNS resolution

if goal is to look at URL pattern (not involving DNS resolution) then syntax to be used is:
shExpMatch(url,
url.substring

However, shExpMatch(host, does work  too  if you match the fqdn part of URL only 8) (although this is quite confusing, I agree)

Hey chris,

thank you for helping with the PAC file. I had alook on the internet and found this:
http://findproxyforurl.com/pac-functions/
but for me this is all quite confusing.

Could you be so kind a create a PAC file which could help with DNSBL and squid?

Lets say we have these IPs:

pfsense LAN-IP: 192.168.10.1 /24
pfsense WAN-IP: 192.168.178.254 /24
DNSBL VIP: 10.123.123.123

Could you show me a PAC file which will make sure that every connection to the internet will be checked against DNSBL?

Don't know if this is "easy" to do but at the moment I am totally confused ;-)

Regards

[BBcan177]

@simby:

Hi!

i have error:

There were error(s) loading the rules: /tmp/rules.debug:40: cannot define table pfB_Malicious: Cannot allocate memory - The line in question reads [40]: table persist file "/var/db/aliastables/pfB_Malicious.txt" @ 2016-04-26 07:10:37

and i have 16GB memory on i7

What is the problem?

Hi simby,

The package defaults the System / Advanced / Firewall & NAT / "Firewall Maximum Table Entries" to 2million entries… Did you alter that setting? It's not related to the hardware...

If you hover-over this rule in the Firewall Tab, does it show the IPs? Does the widget have a Red Icon in the far right column?

Can you give some more context to the events that led to this error, and what happened after?

Take a look at the pfblockerng.log for additional clues.