Beta3 bridge



  • This normal state of configuration for bridge?
    Beta2->upgBeta3

    $ ifconfig
    rl0: flags=8943 <up,broadcast,running,promisc,simplex,multicast>mtu 1500
    	options=8 <vlan_mtu>inet6 fe80::2c1:28ff:fe01:ff3%rl0 prefixlen 64 scopeid 0x1 
    	inet 10.62.0.3 netmask 0xffffff00 broadcast 10.62.0.255
    	ether 00:c1:28:01:0f:f3
    	media: Ethernet autoselect (100baseTX <full-duplex>)
    	status: active
    ed0: flags=8943 <up,broadcast,running,promisc,simplex,multicast>mtu 1500
    	inet6 fe80::250:bfff:fe68:4337%ed0 prefixlen 64 scopeid 0x2 
    	inet 10.62.0.3 netmask 0xffffff00 broadcast 10.62.0.255
    	ether 00:50:bf:68:43:37
    	media: Ethernet autoselect (10baseT/UTP)
    pfsync0: flags=41 <up,running>mtu 1348
    	pfsync: syncdev: rl0 maxupd: 128
    lo0: flags=8049 <up,loopback,running,multicast>mtu 16384
    	inet 127.0.0.1 netmask 0xff000000 
    	inet6 ::1 prefixlen 128 
    	inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 
    pflog0: flags=100 <promisc>mtu 33208
    bridge0: flags=8043 <up,broadcast,running,multicast>mtu 1500
    	ether ac:de:48:3e:40:a1
    	priority 32768 hellotime 2 fwddelay 15 maxage 20
    	member: ed0 flags=7 <learning,discover,stp>port 2 priority 128 path cost 55 disabled
    	member: rl0 flags=7 <learning,discover,stp>port 1 priority 128 path cost 55 forwarding
    carp0: flags=49 <up,loopback,running>mtu 1500
    	carp: MASTER vhid 1 advbase 1 advskew 0</up,loopback,running></learning,discover,stp></learning,discover,stp></up,broadcast,running,multicast></promisc></up,loopback,running,multicast></up,running></up,broadcast,running,promisc,simplex,multicast></full-duplex></vlan_mtu></up,broadcast,running,promisc,simplex,multicast>
    

    I unsure for this

    bridge0: flags=8043 <up,broadcast,running,multicast>mtu 1500
    	ether ac:de:48:3e:40:a1
    	priority 32768 hellotime 2 fwddelay 15 maxage 20
    	member: ed0 flags=7 <learning,discover,stp>port 2 priority 128 path cost 55 disabled</learning,discover,stp></up,broadcast,running,multicast>
    

    Sory for new topic



  • OK
    this resolve

    In Ed0 i change net card

    Tomorrow i read about FreeBSD bridge. Bridge interface too, but in webgui this interface not present. And firewall cant filtered them. May be possible add Bridge interface IF them activate?

    I understand problem with this. But for user-configuration this is more simplest



  • For success activate bridge
    IFCONFIG - all interfaces must be status active (check this)
    interfaces must be plugin to active lan hardvare
    interfaces cant plug to one switch or make cirkle sheme

    In bridge0 all members must be forwarding state.

    Need add procedure to webgui for test bridge problem (for begining – with writen me)

    Next time i test Firewall with bridge & possoble write about


Log in to reply