Beta3 bridge

dvserg

This normal state of configuration for bridge?
Beta2->upgBeta3

$ ifconfig
rl0: flags=8943 <up,broadcast,running,promisc,simplex,multicast>mtu 1500
	options=8 <vlan_mtu>inet6 fe80::2c1:28ff:fe01:ff3%rl0 prefixlen 64 scopeid 0x1 
	inet 10.62.0.3 netmask 0xffffff00 broadcast 10.62.0.255
	ether 00:c1:28:01:0f:f3
	media: Ethernet autoselect (100baseTX <full-duplex>)
	status: active
ed0: flags=8943 <up,broadcast,running,promisc,simplex,multicast>mtu 1500
	inet6 fe80::250:bfff:fe68:4337%ed0 prefixlen 64 scopeid 0x2 
	inet 10.62.0.3 netmask 0xffffff00 broadcast 10.62.0.255
	ether 00:50:bf:68:43:37
	media: Ethernet autoselect (10baseT/UTP)
pfsync0: flags=41 <up,running>mtu 1348
	pfsync: syncdev: rl0 maxupd: 128
lo0: flags=8049 <up,loopback,running,multicast>mtu 16384
	inet 127.0.0.1 netmask 0xff000000 
	inet6 ::1 prefixlen 128 
	inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 
pflog0: flags=100 <promisc>mtu 33208
bridge0: flags=8043 <up,broadcast,running,multicast>mtu 1500
	ether ac:de:48:3e:40:a1
	priority 32768 hellotime 2 fwddelay 15 maxage 20
	member: ed0 flags=7 <learning,discover,stp>port 2 priority 128 path cost 55 disabled
	member: rl0 flags=7 <learning,discover,stp>port 1 priority 128 path cost 55 forwarding
carp0: flags=49 <up,loopback,running>mtu 1500
	carp: MASTER vhid 1 advbase 1 advskew 0</up,loopback,running></learning,discover,stp></learning,discover,stp></up,broadcast,running,multicast></promisc></up,loopback,running,multicast></up,running></up,broadcast,running,promisc,simplex,multicast></full-duplex></vlan_mtu></up,broadcast,running,promisc,simplex,multicast>

I unsure for this

bridge0: flags=8043 <up,broadcast,running,multicast>mtu 1500
	ether ac:de:48:3e:40:a1
	priority 32768 hellotime 2 fwddelay 15 maxage 20
	member: ed0 flags=7 <learning,discover,stp>port 2 priority 128 path cost 55 disabled</learning,discover,stp></up,broadcast,running,multicast>

Sory for new topic

dvserg

OK
this resolve

In Ed0 i change net card

Tomorrow i read about FreeBSD bridge. Bridge interface too, but in webgui this interface not present. And firewall cant filtered them. May be possible add Bridge interface IF them activate?

I understand problem with this. But for user-configuration this is more simplest

dvserg

For success activate bridge
IFCONFIG - all interfaces must be status active (check this)
interfaces must be plugin to active lan hardvare
interfaces cant plug to one switch or make cirkle sheme

In bridge0 all members must be forwarding state.

Need add procedure to webgui for test bridge problem (for begining – with writen me)

Next time i test Firewall with bridge & possoble write about