Cron for WOL

Bob.Dig

Also had no luck getting wol with cron to work, the command is not even working in the GUI command prompt...

/usr/local/bin/wol -v -i 192.168.1.21 dx:50:99:92:11:e7
/usr/local/bin/wol dx:50:99:92:11:e7

But working flawlessly via the pfSense >Services>Wake-on-LAN

Gertjan

I ping 192.168.1.2 : it's powered down.
I "wol" it.
It ping again and it replies ....

[2.5.2-RELEASE][admin@pfsense.local.net]/root: wol
wol: Too few arguments.
Try `wol --help' for more information.
[2.5.2-RELEASE][admin@pfsense.local.net]/root: ping 192.168.1.2
PING 192.168.1.2 (192.168.1.2): 56 data bytes
^C
--- 192.168.1.2 ping statistics ---
3 packets transmitted, 0 packets received, 100.0% packet loss
[2.5.2-RELEASE][admin@pfsense.brit-hotel-fumel.net]/root:  wol -v -i 192.168.1.2 00:4e:01:ac:ca:9c
Waking up 00:4e:01:ac:ca:9c with 192.168.1.2:40000...
[2.5.2-RELEASE][admin@pfsense.local.net]/root: ping 192.168.1.2
PING 192.168.1.2 (192.168.1.2): 56 data bytes
64 bytes from 192.168.1.2: icmp_seq=2 ttl=128 time=0.255 ms
64 bytes from 192.168.1.2: icmp_seq=3 ttl=128 time=0.325 ms
64 bytes from 192.168.1.2: icmp_seq=4 ttl=128 time=0.333 ms
64 bytes from 192.168.1.2: icmp_seq=5 ttl=128 time=0.291 ms
^C
--- 192.168.1.2 ping statistics ---
6 packets transmitted, 4 packets received, 33.3% packet loss
round-trip min/avg/max/stddev = 0.255/0.301/0.333/0.031 ms

In the past, when wol was still a magic (pun intended) thing, there was a tool that you could run on the device to be waken up : it showes you that it's NIC did receive the magic wake up packets.
These packets are used to wake up the device, if it is able to do so, and if it was allowed to do (by driver and or BIOS settings).

Bob.Dig

@gertjan One difference might be that my NIC doesn't have an IP address, its only purpose it to wake up the PC.

And again, it is working flawlessly via the GUI Services>Wake-on-LAN

Gertjan

@bob-dig said in Cron for WOL:

And again, it is working flawlessly via the GUI Services>Wake-on-LAN

GUI Services>Wake-on-LAN ?
Aha, you mean https://pfsense.yourlocal.tld/services_wol.php.

You had a look how "services_wol.php" does it's wol thing ?
( it used the wol command like you ;) )

See here https://github.com/pfsense/pfsense/blob/master/src/usr/local/www/services_wol.php - line 51.

'wol' needs an IP ( ?) so it can determine the interface to be used..
The interface has an IP, right ?

When I used a fake IP, like 192.168.1.200 instead of 192.168.2, my "00:4e:01:ac:ca:9c" device didn't wake up.

stephenw10

What happens if you use the pfSense interface IP there? In the same segment as the target?

Bob.Dig

@stephenw10 Doesn't work either and yes.

If I try with putty I get this.

[2.5.2-RELEASE][admin@pfSense.home.arpa]/root: /usr/local/bin/wol -v -i 192.168.1.1 d0:50:99:92:11:e7
Waking up d0:50:99:92:11:e7 with 192.168.1.1:40000...
[2.5.2-RELEASE][admin@pfSense.home.arpa]/root: /usr/local/bin/wol -v d0:50:99:92:11:e7
/usr/local/bin/wol: Cannot send magic packet for 'd0:50:99:92:11:e7' to 255.255.255.255:40000: Permission denied
[2.5.2-RELEASE][admin@pfSense.home.arpa]/root: /usr/local/bin/wol d0:50:99:92:11:e7
/usr/local/bin/wol: Cannot send magic packet for 'd0:50:99:92:11:e7' to 255.255.255.255:40000: Permission denied
[2.5.2-RELEASE][admin@pfSense.home.arpa]/root:

But again, none of this worked.

Gertjan

@bob-dig

If your "device without IP" ( ~~serious ??~~ see below ) is some windows device, try this :

https://www.depicus.com/wake-on-lan/wake-on-lan-monitor

I had to indicate a port number like "40000" on both side so the command line works :

wol -i 192.168.1.2 00:4e:01:ac:ca:9c -p 4000
Waking up 00:4e:01:ac:ca:9c...

The tool on the device, my PC, that it received the special pachet (5 times the device MAC as the data payload)

See also the FreeBSD mn page for wol https://www.freebsd.org/cgi/man.cgi?query=wol&manpath=ports&sektion=1

edit : a device in lower power mode doesn't have - use an IP(v4 or v6).
It just listens to the incoming data stream, and knows how to detect if it's won MAC is present 5 times in a row. No processor power is needed.

wol needs a IP or host just to so it can find out on what interface to use if it is "multi homed", like our pfSense. The actual IP shouldn't matter ......
But .....
I think that our switches play an important role here. Switches are not hubs, so traffic isn't broadcasted any more.
When I use the broadcast IP of my LAN, like :

wol -i 192.168.1.255 -p 4000 00:4e:01:ac:ca:9c

it worked, the Wake On Lan monitor on my PC showed the incoming magic packet.

Bob.Dig

@gertjan I want to use wol (not pattern match?) for this. I ended up using wol.exe on another Windows host together with windows tasksheduler to achieve what pfSense couldn't do for me.

Gertjan

@bob-dig I edited - see above.

Bob.Dig

@gertjan So this time I tried in putty:

/usr/local/bin/wol -v -i 192.168.1.255 d0:50:99:92:11:e7

And it did work. Then I tried cron, also does work!

So the key is to use .255 at the end.

I still wonder why the web-GUI-thingy works with the MAC only, but on the other hand, when I first added the host to the Wake-on-LAN Devices list, it had an IP-address, so it might have saved it there.

Thank you @Gertjan !!