[solved] pfSense (2.6.0 & 22.01 ) is very slow on Hyper-V

PaulPrior

@stephenw10 I disabled all of the hardware offloading (and many combinations of partially on and off). The only setting that increased speed was to disable ALTQ support which doubled the throughput but since it has already become about 10-20 times slower a doubling wasn't great.
All of my adapters are Hyper-V virtual adapters except for the one on the WAN interface which bonds to a physical intel adapter.
Back on v2.5.2 now and inter-vlan performance is an order of magnitude better.

DonZalmrol

@paulprior glad to hear that, I'm going to rollback my other site (B) and keep this one on 2.6.0 for further troubleshooting.

Bob.Dig

@dominixise said in After Upgrade inter (V)LAN communication is very slow (on Hyper-V).:

Here is some links with info that might be helpful:
https://superuser.com/questions/1266248/hyper-v-external-network-switch-kills-my-hosts-network-performance

I already tried using just private vSwitches, nothing changed.

@stephenw10 said in After Upgrade inter (V)LAN communication is very slow (on Hyper-V).:

There are two loader variables we set in Azure that you don't have:

I added those to "SystemAdvancedSystem Tunables" and did a reboot but it didn't changed anything.

I did some more iperfing, this time also the other way around, so I changed client and server and there it shows:

C:\>iperf2.exe -c 192.168.1.10 -p 4711 -t 60 -i 10
------------------------------------------------------------
Client connecting to 192.168.1.10, TCP port 4711
TCP window size: 64.0 KByte (default)
------------------------------------------------------------
[  1] local 192.168.183.10 port 55124 connected with 192.168.1.10 port 4711
[ ID] Interval       Transfer     Bandwidth
[  1] 0.00-10.00 sec  1.38 MBytes  1.15 Mbits/sec
[  1] 10.00-20.00 sec   128 KBytes   105 Kbits/sec
[  1] 20.00-30.00 sec   256 KBytes   210 Kbits/sec
[  1] 30.00-40.00 sec   256 KBytes   210 Kbits/sec
[  1] 40.00-50.00 sec   128 KBytes   105 Kbits/sec
[  1] 50.00-60.00 sec   256 KBytes   210 Kbits/sec
[  1] 0.00-123.86 sec  2.38 MBytes   161 Kbits/sec

C:\>iperf2.exe -c 192.168.183.10 -p 4711 -t 60 -i 10
------------------------------------------------------------
Client connecting to 192.168.183.10, TCP port 4711
TCP window size: 64.0 KByte (default)
------------------------------------------------------------
[  1] local 192.168.1.10 port 56363 connected with 192.168.183.10 port 4711
[ ID] Interval       Transfer     Bandwidth
[  1] 0.00-10.00 sec  6.29 GBytes  5.41 Gbits/sec
[  1] 10.00-20.00 sec  6.28 GBytes  5.40 Gbits/sec
[  1] 20.00-30.00 sec  6.94 GBytes  5.97 Gbits/sec
[  1] 30.00-40.00 sec  6.81 GBytes  5.85 Gbits/sec
[  1] 40.00-50.00 sec  6.99 GBytes  6.01 Gbits/sec
[  1] 50.00-60.00 sec  6.94 GBytes  5.96 Gbits/sec
[  1] 0.00-60.00 sec  40.3 GBytes  5.77 Gbits/sec

Only tcp is affected and it only shows when "my" machine is the server, not the other way around. It is not SMB specific and I already mentioned that connecting to socks proxy in another vlan also makes these problems.

Bob.Dig

I made yet another test, just private switches between two VMs and the pfSense VM, no external, no physical switch involved and no VLAN.

Again TCP is problematic, this time in both directions. One UDP bench for reference.

C:\>iperf2.exe -c 192.168.45.100 -p 4711 -t 60 -i 10
------------------------------------------------------------
Client connecting to 192.168.45.100, TCP port 4711
TCP window size: 64.0 KByte (default)
------------------------------------------------------------
[  1] local 192.168.44.100 port 52446 connected with 192.168.45.100 port 4711
[ ID] Interval       Transfer     Bandwidth
[  1] 0.00-10.00 sec   384 KBytes   315 Kbits/sec
[  1] 10.00-20.00 sec   256 KBytes   210 Kbits/sec
[  1] 20.00-30.00 sec   128 KBytes   105 Kbits/sec
[  1] 30.00-40.00 sec   256 KBytes   210 Kbits/sec
[  1] 40.00-50.00 sec   256 KBytes   210 Kbits/sec
[  1] 50.00-60.00 sec   128 KBytes   105 Kbits/sec
[  1] 0.00-121.14 sec  1.38 MBytes  95.2 Kbits/sec


C:\>iperf2.exe -c 192.168.44.100 -p 4711 -t 60 -i 10
------------------------------------------------------------
Client connecting to 192.168.44.100, TCP port 4711
TCP window size: 64.0 KByte (default)
------------------------------------------------------------
[  1] local 192.168.45.100 port 55314 connected with 192.168.44.100 port 4711
[ ID] Interval       Transfer     Bandwidth
[  1] 0.00-10.00 sec  4.00 MBytes  3.36 Mbits/sec
[  1] 10.00-20.00 sec  3.88 MBytes  3.25 Mbits/sec
[  1] 20.00-30.00 sec  3.88 MBytes  3.25 Mbits/sec
[  1] 30.00-40.00 sec  3.88 MBytes  3.25 Mbits/sec
[  1] 40.00-50.00 sec  3.88 MBytes  3.25 Mbits/sec
[  1] 50.00-60.00 sec  3.88 MBytes  3.25 Mbits/sec
[  1] 0.00-61.97 sec  23.5 MBytes  3.18 Mbits/sec


C:\>iperf2.exe -c 192.168.44.100 -p 4712 -u -t 60 -i 10 -b 10000M
------------------------------------------------------------
Client connecting to 192.168.44.100, UDP port 4712
Sending 1470 byte datagrams, IPG target: 1.12 us (kalman adjust)
UDP buffer size: 64.0 KByte (default)
------------------------------------------------------------
[  1] local 192.168.45.100 port 62027 connected with 192.168.44.100 port 4712
[ ID] Interval       Transfer     Bandwidth
[  1] 0.00-10.00 sec  3.61 GBytes  3.10 Gbits/sec
[  1] 10.00-20.00 sec  3.63 GBytes  3.12 Gbits/sec
[  1] 20.00-30.00 sec  3.67 GBytes  3.15 Gbits/sec
[  1] 30.00-40.00 sec  3.63 GBytes  3.12 Gbits/sec
[  1] 40.00-50.00 sec  3.67 GBytes  3.15 Gbits/sec
[  1] 50.00-60.00 sec  3.70 GBytes  3.18 Gbits/sec
[  1] 0.00-60.00 sec  21.9 GBytes  3.14 Gbits/sec
[  1] Sent 16009349 datagrams
[  1] Server Report:
[ ID] Interval       Transfer     Bandwidth        Jitter   Lost/Total Datagrams
[  1] 0.00-60.00 sec  21.6 GBytes  3.09 Gbits/sec   0.915 ms 254222/16009348 (1.6%)

I am kinda done.

DonZalmrol

@bob-dig how is your Hyper-V guest set up? Similar to mine? Perhaps you need to disable VMQ and SR-IOV and test again?

Bob.Dig

@donzalmrol Already did this, didn't helped.

DonZalmrol

Ran an Iperf between two 10G my host and one guest:

Receive quite good results on both TCP and UDP.

ttmcmurry

This same scenario just played out in my environment as well. I spent hours on the line with my ISP trying to figure it out and left for the night with them escalating to a higher level technician.

It occurred to me after getting off the phone to search the internet for pfsense and hyper-v in the last week and it led me straight to this article. The hyper-v config changes for RSC were unnecessary for my setup (it was already $false).

I just spun up a new pfSense Hyper-V VM running 2.5.2 and restored from pfSense Auto Backup using the pre-upgrade auto config save, and everything is running perfectly. There were no Windows updates, no changes to Hyper-V / I reverted the settings I changed during diagnostics.

There's certainly something not right with 2.6.0. I re-learned that I need to make fewer major changes in one setting.

I took the opportunity to test pfSense 2.6.0 on various versions of Windows & Hyper-V. This same behavior occurred in Server 2016 (14393.4886), Windows 10 (19044.1526), and Windows 11 (22000.493).

Bob.Dig

@ttmcmurry said in After Upgrade inter (V)LAN communication is very slow (on Hyper-V).:

I took the opportunity to test pfSense 2.6.0 on various versions of Windows & Hyper-V. This same behavior occurred in Server 2016 (14393.4886), Windows 10 (19044.1526), and Windows 11 (22000.493).

That must have been some immense work on your part. What have you tried other then changing the host os?

ttmcmurry

@bob-dig it didn't take that much time :) pfSense installs & configures fast! I grabbed two laptops, stuck some extra USB NICs on them, then probably spent 15 minutes on each installation to reproduce the issue. The ease of reproducing the issue across various hardware and Windows versions does speak to the consistency of the pfSense software; even though it has this undesirable problem, at least it's consistent and reproducible. Theoretically making finding the root cause easier.

Other things I tried

Reboots (Gateway, Switch, Host, VM)
On the same day I upgraded to 2.6, my ATT Gateway also got a firmware release. I jumped to conclusions & laid blame upon ATT and pursued them for a fix that was never to come.
Examined Hyper-V vSwitch settings to ensure they were configured appropriately, bound to the correct physical uplinks (no changes made)
Examined HV VM vNIC settings to ensure nothing has changed; set to pfSense recommendations (no changes made)
Double checked my switching for loops/STP, logs, errors, unexpected BPDUs from someone adding a switch somewhere I didn't know about
Interfaced with the ATT Gateway directly with laptop to test performance (this led to isolating Hyper-V as the problem)
Upgraded Intel I350-T4 drivers & PROset to 27.0 (2022/02/09) which didn't fix or make anything worse.

stephenw10

And you are also seeing it specifically between VLANs on hn(4) NICs?

ttmcmurry

@stephenw10 Good day! In the pfSense VM, the interfaces are not associated with VLANs and there are no VLANs defined. From pfSense's perspective, it is working with native hn(x) interfaces.

Hyper-V's vSwitches are all untagged. All VM vNICs in HV are untagged.

VLANs exist past the physical uplinks in the Physical Switch.

werter

Decision: do not use hyper-v as virtualization platform ))
Better try Proxmox VE (open source)

Bob.Dig

@bob-dig said in After Upgrade inter (V)LAN communication is very slow (on Hyper-V).:

It wouldn't been the first time I had to install pfSense fresh from the get-go after a new version. Whatever my usecase is, it might be special...
So I guess "This is the Way".

Wasn't the way, creating a fresh pfSense-CE-2.6.0 sadly changed nothing.

If of interest:

ttmcmurry

@bob-dig yep. Thx for validating. 2.5.2 is fine, use that till they resolve the issue.

Bob.Dig

@ttmcmurry said in After Upgrade inter (V)LAN communication is very slow (on Hyper-V).:

2.5.2 is fine, use that till they resolve the issue.

If netgate does, they seem to care only for azure and we all know since the exchange debacle, that the MS Cloud is not the same as MS's server products... So my hopes are rather low on this. Might have to try with DDA once again.

DD

@bob-dig Or we switch to OPNsense which is working ok on the same system where pfSense is not working ok.

Bob.Dig

@dd I couldn't even install OPNsense on hyper-v not long ago, you had to do a trick, and those guys want to use the normal FreeBSD too.
I am stuck, if DDA is not going to work. I have hard time to change my firewall Distro but even more changing my Homserver OS...

DD

@bob-dig They have new version 22.1 which is based on FreeBSD 13 and it's working ok. I have tried it. I think that problem with pfSense 2.6 is because it's based on FreeBSD 12.3. Same problem is with pfSense 2.7.0-DEVELOPMENT which is on FreeBSD 12.3 too. I think, fix will not be available for longer time but they must something to do because now is not pfSense 2.6 (and Plus) useable on Hyper-V.

johnpoz

@dd said in After Upgrade inter (V)LAN communication is very slow (on Hyper-V).:

They have new version 22.1 which is based on FreeBSD 13 and it's working ok.

Huh? 22.01 is using 12.3 same as 2.6