SG-5100 -- Verify that M.2 SSD is recognized after physically installing.
-
Thanks for taking the time to explain how to do this, it is much appreciated and was most helpful, pete
-
I’m in precisely the same situation on our SG-5100 with failing eMMC and a M.2 installed. I spent some time today going through every menu item. Besides disabling it in the Boot menu, I can’t seem to completely disable it.
At the moment I’m coming to accept that booting will take about 10 minutes longer than it should.
Edit - Disabling instructions followed:
https://forum.netgate.com/topic/168299/sg-5100-disable-onboard-emmc/2 -
Do you also see the "A2" POST code?
-
I will note that on my system that the eMMC is not disabled, but is at a lower boot priority.
It has been so long now, I have no idea if it still works, but does show in the boot menu.
In that sense I never disabled the eMMC.
So, can you "see" the new M.2 drive in the boot menus like I showed?
I had a larger one (in Gb), but the protocol was a little bit more advanced and the bios/M.2 port was not having it.I think from here you should let @stephenw10 guide you.
Phizix
P.S. Note, I LOVE my SG-5100 and will never go back to consumer/pro-sumer junk er . . . I mean hardware again!!
-
@stephenw10 I think the A2 POST code may have flashed, but I’m not 100% sure. It takes soooooo long. The last time I played with it, I saw B2 for the first couple minutes, then it changed to B4 right before it finally gave me the option to press F12.
-
@phizix said in SG-5100 -- Verify that M.2 SSD is recognized after physically installing.:
I will note that on my system that the eMmMC is not disabled, but is at a lower boot priority.
It has been so long now, I have no idea if it still works, but does show in the boot menu.
In that sense I never disabled the eMMC.
So, can you "see" the new M.2 drive in the boot menus like I showed?
I had a larger one (in Gb), but the protocol was a little bit more advanced and the bios/M.2 port was not having it.I think from here you should let @stephenw10 guide you.
Phizix
P.S. Note, I LOVE my SG-5100 and will never go back to consumer/pro-sumer junk er . . . I mean hardware again!!
Yes, I can see the M.2 in the boot options and it is set as a higher priority as described above.
-
@lamaz
So now the question is, have you loaded the bootable image on it? If not it will still fall through to the eMMC.Phizix
-
@phizix said in SG-5100 -- Verify that M.2 SSD is recognized after physically installing.:
@lamaz
So now the question is, have you loaded the bootable image on it? If not it will still fall through to the eMMC.Phizix
Just to be clear, my SG-5100 runs great with the M.2 as the boot device (after a very long boot wait). The eMMC has failed and will no longer boot.
-
It must be trying to read the eMMC signature during post and finally gives up. @stephenw10 may be able to shed some light on that. Or tell if there is some way to prevent the BIOS from attempting to detect it.
Phizix
-
@lamaz said in SG-5100 -- Verify that M.2 SSD is recognized after physically installing.:
https://forum.netgate.com/topic/168299/sg-5100-disable-onboard-emmc/2
The poster never responded on that thread. So same question here. Does the eMMC device still appear in the SDIO config menu?
Steve
-
P Phizix referenced this topic on
