Weird Behavior with x710-da2 in 2.5.x
-
Hi @ashtonianagain - looking at the logs above:
- If the card is PCI Express 3.0, I'd expect the bus speed to be higher (e.g. 8.0GT/s), but that will depend on which the slot the card is sitting in on the motherboard it - could be that the bandwidth is shared or the slot is only 2.0/2.1 capable.
- I also saw that your system defaulted to using MSI vs. MSI-X. Are you passing the card through to pfSense or going fully virtual? A couple links to check out that may help:
https://forum.netgate.com/topic/158860/pfsense-latency-spikes-in-esxi
https://forum.netgate.com/topic/157688/remove-vmware-msi-x-from-the-pci-blacklist/In particular, this setting might help with some of the performance issues you are seeing:
hw.pci.honor_msi_blacklist=0Hope this helps.
-
That syctl usually only affects vmxnet, which are on the MSI blacklist by default. But there's no harm setting it.
-
@stephenw10 said in Weird Behavior with x710-da2 in 2.5.x:
That syctl usually only affects vmxnet, which are on the MSI blacklist by default. But there's no harm setting it.
That's a good point - I was just going by the last post in this thread, thinking it might be worth a shot:
https://forum.netgate.com/topic/157688/remove-vmware-msi-x-from-the-pci-blacklist/5
-
@tman222 said in Weird Behavior with x710-da2 in 2.5.x:
hw.pci.honor_msi_blacklist=0
THIS WORKED! thank you guys for your help. After setting this I've been able to get normal pings and expected bandwidth performance.
Now Im not sure if I should enable or disable all the of the offloading for performance - what do you guys think?
-
Nice. That's interesting. I wonder what is on that list that affects pass-through NICs.
Good catch @tman222
The hardware off-load settings rarely make much difference. I would certainly not enable anything that's disabled by default. So that means only checksum off-load which is still enabled by default.
Steve
-
@stephenw10 said in Weird Behavior with x710-da2 in 2.5.x:
Nice. That's interesting. I wonder what is on that list that affects pass-through NICs.
Good catch @tman222
The hardware off-load settings rarely make much difference. I would certainly not enable anything that's disabled by default. So that means only checksum off-load which is still enabled by default.
Steve
Hi @stephenw10 - looking Jim's comment here and the bug report (towards the end):
https://forum.netgate.com/topic/157688/remove-vmware-msi-x-from-the-pci-blacklist/2
https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=203874If I understand right, this fix never made into FreeBSD 12. Would it be worth raising an issue on Redmine? At the very least, if the fix is missing, maybe add the sysctl tunable?
Thanks in advance!
-
I had thought this only applied to the vmxnet NICs but if you look at the diff on the patch it actually applied to the VMWare PCI bridge so I guess this could still be in play.
It is odd though, it still comes up with 6 queues in the above example, just using MSI not MSIX. -
I am the other individual mentioned. I have a Quad SFP+ PCI-e 3x card on a ESXi 6.7U3 server. It's an OEM? card (Branded- Silicom PE310G4I71LB-XR) which runs an older FW. I have passed through 2 ports to pfSense and it had the same latency issues mentioned but is working perfectly fine in Windows 10, Server 2022 and Sophos UTM (bleh). I will attempt the above fix this weekend when I perform a switchover and report back.
-
Issue still present on below build, resolved with the same change mentioned above.
2.7.0-DEVELOPMENT (amd64)
built on Fri Feb 04 19:41:27 UTC 2022
FreeBSD 12.3-STABLE -
@deridiot said in Weird Behavior with x710-da2 in 2.5.x:
Issue still present on below build, resolved with the same change mentioned above.
2.7.0-DEVELOPMENT (amd64)
built on Fri Feb 04 19:41:27 UTC 2022
FreeBSD 12.3-STABLEInstalling 2.6 and update to 21.05.2 was solving that problem for a X710-T2 adapter, so perhaps it could work for you too.
