Difference of whitebox vs SG-6100
-
@nimrod said in Difference of whitebox vs SG-6100:
It doesnt matter to me really. Thats something my friend has to live with. As for me, im running Protectli FW6D with zero issues.
Protectli seems to be a rebranded Yanling
https://www.ylipc.com/product/category/network_serverI have just got a HYSTOU 6 port i3-7100 - Yanling clone , for playing around with.
https://www.ylipc.com/product/N13L6
https://eu.protectli.com/product/fw6b/Has the older Intel gigabit interfaces emX , but the price was less than $200 for 8GRam + 160GB HDD , and powerusage low.
I see no difference in quality from my i3 Qotom's
It uses a "Cisco console RJ45 plug" instead of a "Real DE-9" plug. -
@bingo600 said in Difference of whitebox vs SG-6100:
@nimrod said in Difference of whitebox vs SG-6100:
It doesnt matter to me really. Thats something my friend has to live with. As for me, im running Protectli FW6D with zero issues.
Protectli seems to be a rebranded Yanling
https://www.ylipc.com/product/category/network_serverI have just got a HYSTOU 6 port i3-7100 - Yanling clone , for playing around with.
https://www.ylipc.com/product/N13L6
https://eu.protectli.com/product/fw6b/Has the older Intel gigabit interfaces emX , but the price was less than $200 for 8GRam + 160GB HDD , and powerusage low.
I see no difference in quality from my i3 Qotom's
It uses a "Cisco console RJ45 plug" instead of a "Real DE-9" plug.I actually ordered my unit from Yanling directly. Protectli is just providing sales in USA, technical support, hardware upgrades and excellent documentation. Yanling is original manufacturer. And this is not your typical low quality cheap Chinese hardware. These units are very expensive, but build quality is unmatched. Qotom is no match when it comes to build quality. And CoreBoot BIOS can be installed on all Yanling units. Unlike Qotom, they just work with zero hassle. But thats why they cost more.
-
@nimrod said in Difference of whitebox vs SG-6100:
And this is not your typical low quality cheap Chinese hardware. These units are very expensive, but build quality is unmatched.
I have seen both units , and their build quality seems similar to me.
And i have a lot of embedded experience.Qotom is no match when it comes to build quality. And CoreBoot BIOS can be installed on all Yanling units. Unlike Qotom, they just work with zero hassle. But thats why they cost more.
I and many other have been using Qotom for a long time wo. any issues.
You must have been super unlucky with your Qotom experience , or just promoting your own choice.How many Qotoms have you had experience with ?
I must admit that the Coreboot Bios is a nice feature
But that's the only thing i miss on my Qotoms.
Btw:
All my i3's will play the "pfSense is ready (booted) melody"
And i see no issue powering off/on.I do see a protection kicking in if you jerk out the power plug , and insert it immediately again. You have to wait 30+ secs in order for the unit to power on.
I see that a lot on well designed embedded devices , it makes the PSU Caps discharge , before applying power again. To prevent overshooting.It's nice you're happy with your Yanling.
There's a lot of people beung happy w. their Qotoms too.Edit:
One thing i miss on my 4-port i5's, but has on my i3's , and the Yanling.
Is the ability to reroute the Bios Console to serial.
Thats a neat feature that enables you to pull a machine up from "blank" just with a serial connection ... Ie. via a TeamViewer./Bingo
-
@bingo600 said in Difference of whitebox vs SG-6100:
One thing i miss on my 4-port i5's, but has on my i3's , and the Yanling.
Is the ability to reroute the Bios Console to serial.I have a Kettop Mi-4300YL (I5, 4xIntel LAN), the MoBo is branded "Q3XXG4-P" what make me think its Qotom and in the Bios I can reroute the Bios-Console to serial ...
-
@fireodo
I think Kettop is a rebranded Qotom too.
My i5's are from 2017, and my i3's from 2019.
Could be a design change during that time./Bingo
-
@bingo600 said in Difference of whitebox vs SG-6100:
My i5's are from 2017, and my i3's from 2019.
Could be a design change during that time.That could be an explanation - I bought mine in november 2020 ...
-
Hi there,
in my own personal opinion:
the main advantage (besides those already pointed out) of the 6100 is the possibility of building you multi gigabit LAN.Your current whitebox has max 1 gbit LAN interfaces, alle the apu, ipu, protectli, quotom stuff also comes with 1 gbit max.
The 6100 offers 4 x 2,5 gbits, 2 sftp+ 10 gbit and 2 combo 1 gbit interfaces, if i recall it correctly.
So even if you dont make use of it from day one...you might be happy about it in a few years.
be advised: i have no personal experience with netgate's devices....apu still doing the job here but seriously considering switching to the 6100...
:)
edit: whether or not pfsense can really work with 10gbits...still worth a thought, jm2c.the other
-
@the-other said in Difference of whitebox vs SG-6100:
The 6100 offers 4 x 2,5 gbits, 2 sftp+ 10 gbit and 2 combo 1 gbit interfaces, if i recall it correctly.
The 6100 is without doubt the better system BUT in some cases it can be overkill - so its only a matter of what is needed! (for a home environment a i5 Qotom might be allready too much ...)
IMHO -
@bingo600 said in Difference of whitebox vs SG-6100:
I have seen both units , and their build quality seems similar to me.
And i have a lot of embedded experience.Well let me put it this way. I have opened my Yanling units several times to add additional storage and more memory. I never had any issues with tightening up the small screws that hold the bottom cover. I opened several Qotom devices for same reasons, and each time i put the screws back in and tight them up (not excessively) the threading in the holes slips and gets destroyed. Its the cheaper unit made with cheaper much softer metal. I mean. Price tells you everything you need to know about quality. Pay attention to drilling quality on holes for the WiFi antennas. Qotom leaves sharp edges inside and you can easily cut yourself if you are not careful. That low price comes from cheaper machining of the case, and it clearly shows. There is no shame in that. You get what you pay for.
I and many other have been using Qotom for a long time wo. any issues.
Dont get me wrong man. Qotom`s are great considering the price. If we are talking bang for the buck, Qotom is great balance. As long as the case is able to provide decent cooling for the CPU, who cares what kind of metal is and how it looks. The box is probably going to sit somewhere when no one can see it anyway and no one will ever open it again.
You must have been super unlucky with your Qotom experience , or just promoting your own choice.
Im not one of those guys that thinks "just because its mine, its best". For me, this is just another piece of hardware that gets the job done. But i cant deny the fact that it is top quality device. As for Qotom, as i said, that unit is not mine. But i had experience with several other Qotom devices, but i had no chance to check BIOS and whether or not is working as you describe it. But hey, if you say that this setting can be adjusted in BIOS on i3 and i5 models, thats great. I believe you. I just shared very bad experience i had with the model my friend bought. It was actually me that recommended him Qotom because he wanted to go with those very cheap XCY appliances.
How many Qotoms have you had experience with ?
15 it think. I usually recommend Netgate or Protectli, and if customers want something cheaper, i recommend Qotom. And if thats expensive too, i ditch the customer, because i dont want to deal with issues caused by cheap low quality hardware that doesnt even have Intel NICs. Not a single Netgate, Protectli or Qotom device have ever failed on me. And i want to keep it that way.
I must admit that the Coreboot Bios is a nice feature
But that's the only thing i miss on my Qotoms.
It is nice, but this is not Qotom issue. The only reason Yanling devices are having CoreBoot support is because Protectli hired 3mdeb Embedded Systems Consulting company to create CoreBoot compatible bios for their devices. Same thing can be done for Qotom, but Qotom doesnt care.
Btw:
All my i3's will play the "pfSense is ready (booted) melody"
And i see no issue powering off/on.Not this one. As i said. As soon as pfSense boots up, integrated sound card gets initialized and it hijacks PC speaker sound and it routes it through 9mm headphone jack. Im sure this can be solved by simply disabling onboard audio chip.
-
@nimrod said in Difference of whitebox vs SG-6100:
@bingo600 said in Difference of whitebox vs SG-6100:
I have seen both units , and their build quality seems similar to me.
And i have a lot of embedded experience.Well let me put it this way. I have opened my Yanling units several times to add additional storage and more memory. I never had any issues with tightening up the small screws that hold the bottom cover. I opened several Qotom devices for same reasons, and each time i put the screws back in and tight them up (not excessively) the threading in the holes slips and gets destroyed. Its the cheaper unit made with cheaper much softer metal. I mean. Price tells you everything you need to know about quality.
We change the M2 disk on every upgrade in the Qotoms , always swapping the current working as the spare. And I have never had a single issue with the screws/thread.
We're only using the "Full height" chassis , maybe they're more sturdy.
Buy your pict looks like a "Full height too"
You have really had bad luck with those Qotoms.
Well IMHO i don't see much difference in the models, but maybe the Yanling has better cooling efficiency. I think my HYSTOU i3 runs 3..4 degrees cooler than my Qotom i3 , but then again my Qotom is 2.7GHz the Yanlinh/HYSTOU is 2.4Ghz.
But it seems like the new "low cost" Qotoms have skipped the serial port , as default. That's a bad move
https://www.aliexpress.com/item/1005003799551637.htmlAnd if i should buy devices today for workusage , i'd seriously consider 6100's.
-
@bingo600 said in Difference of whitebox vs SG-6100:
@nimrod said in Difference of whitebox vs SG-6100:
You have really had bad luck with those Qotoms.
Or bad batch of units.
Well IMHO i don't see much difference in the models, but maybe the Yanling has better cooling efficiency. I think my HYSTOU i3 runs 3..4 degrees cooler than my Qotom i3 , but then again my Qotom is 2.7GHz the Yanlinh/HYSTOU is 2.4Ghz.
Yeah that comparison is not valid if both units are not 100% identical. Also, temperatures will vary depending on what kind, and how much thermal paste is applied between CPU heat spreader and the case itself.
But it seems like the new "low cost" Qotoms have skipped the serial port , as default. That's a bad move
https://www.aliexpress.com/item/1005003799551637.htmlI found this jumper issue to be a bigger problem than the lack of port. Its not nice when customer calls you and starts screaming because their network went down after power outage and didnt came back when power was restored. So i have to drive for one hour just so i can set one jumper and press one button.
And if i should buy devices today for workusage , i'd seriously consider 6100's.
They are not always available here in eastern Europe. Thats one of the major reasons people go with other appliances.
-
If you don't
enableDisable this in the newer (my i3) Qotom Bios , you will not see like 70% of the settings , including the Power loss restoreAdvanced -> OEM Form Hide Setup Item - Disabled -
@bingo600 said in Difference of whitebox vs SG-6100:
If you don't enable this in the newer (my i3) Qotom Bios , you will not see like 70% of the settings , including the Power loss restore
Advanced -> OEM Form Hide Setup Item - DisabledThats not the case with this unit. The option is there and clearly visible. However, changing the setting does absolutely nothing. Also, if they already made such stupid decision to control this setting with the jumper, they should at least hide this option in BIOS since it does nothing.
This option being available in BIOS but doing nothing, is only going to cause confusion. People will think unit is faulty because they set the BIOS setting but unit doesnt power on after power loss.
Here is the youtube video explaning this and showing the location of the jumper:
https://www.youtube.com/watch?v=-2pZi3hf2f4
-
@nimrod
How old is the Qotom you had the "Power on issue on ?"I just had a Qotom yesterday, that reported "Bad Battery/CMOS Checksum error" , and had "Blown away" the settings.
I saw it when trying "via the serial console" to "ESC into the Bios", to set it to boot from a 2.6.0 USB Upgrade stick. I never came into the Bios, and had to use USB-KBD + HDMI screen.When checking Serial Console rediection , it was disabled (deault) , the same (default) was the powerloss setting.
That was a a bit early "I have just had them for 2 years".
I took one apart ... It's a CR2032 with molex plug at the end/Bingo
-
@bingo600 said in Difference of whitebox vs SG-6100:
@nimrod
How old is the Qotom you had the "Power on issue on ?"Its a brand new device.
I just had a Qotom yesterday, that reported "Bad Battery/CMOS Checksum error" , and had "Blown away" the settings.
I saw it when trying "via the serial console" to "ESC into the Bios", to set it to boot from a 2.6.0 USB Upgrade stick. I never came into the Bios, and had to use USB-KBD + HDMI screen.When checking Serial Console rediection , it was disabled (deault) , the same (default) was the powerloss setting.
That was a a bit early "I have just had them for 2 years".
I took one apart ... It's a CR2032 with molex plug at the end/Bingo
You have to watch youtube video i posted in previous post. You dont seem to understand that this is not caused by the BIOS not being able to save the changes i made. Problem is the fact that power on setting is not controlled by the BIOS. Its controlled by jumper. BIOS just reads and shows jumper position, thats why this setting gets ignored and gets reverted back to whatever setting was there before. They just left that setting in BIOS for devices that actually support changing this setting via BIOS. And that just shows you how much Qotom cares about consistency and quality.
-
@nimrod
That is NOT correct ...
Maybe you can force it to to Power-On with the jumper , and that might not be a bad choice.
But I have tested the power settings on my Qotoms , and it has been doing precisely what i told it to in the Bios.But when the Bios is "cleared" due to checksum error (bad battery) , and the default is to "Power Off" after powerfailure, then it is what it is doing.
I will exit from this discussion, as i thought you would be open for new info.
But you just seems determined to "Bash Qotom" , and that is your choice.
I will just not participate longer./Bingo
-
@bingo600 said in Difference of whitebox vs SG-6100:
@nimrod
That is NOT correct ...Whats not correct ? Did you even watch the youtube video i posted in previous post? Im not the only one having this issue and there is a good reason why is there a jumper in the first place.
Maybe you can force it to to Power-On with the jumper , and that might not be a bad choice.
You dont seem to understand. What i did is not "forcing it to power on". Its the ONLY WAY to make it power on after power loss.
Jumper is set to position 1-2 by default. Changing the BIOS setting does nothing. Setting the jumper to postion 2-3 powers on device as soon as the power is applied. At that point, BIOS setting is still doing nothing. Is that so difficult to accept or understand ?
But I have tested the power settings on my Qotoms , and it has been doing precisely what i told it to in the Bios.
And i absolutely believe what you said. Thats exactly what the problem is. You are talking about YOUR higher end device which is obviously not the same model as the cheapest device im talking about.
But when the Bios is "cleared" due to checksum error (bad battery) , and the default is to "Power Off" after powerfailure, then it is what it is doing.
I dont have any checksum errors, nor i have need to clear BIOS. As i said, this is brand new device. Not even month old.
I will exit from this discussion, as i thought you would be open for new info.
I dont know why are you taking this personally? Im very open to new info. Im just saying that MY device is not behaving same as YOUR device. This is cheap Celeron J series device, and you are having higher end i3/i5/i7 devices that are obviously designed differently.
But you just seems determined to "Bash Qotom" , and that is your choice.
i have absolutely no reason to bash Qotom or glorify any other brand. Im way too old for that, and this is just a cheap aluminium box that gets the job done. You need to accept the fact that this cheaper model is not built and designed the same way as the higher end Qotom devices you have.
Again, im not glorifying Protectli, but from chepest FW2 model to highest end FW6E model, BIOS is behaving the same. If the hardware feature is not on the board, there will be no setting(s) for it in the BIOS.
Obviously, thats not the case with Qotom. On the cheapest model that i have, there is a setting in the BIOS for a feature which is not BIOS controlled, but jumper controlled.
And then, there are higher end i5 and i7 models which YOU have, and they have this same setting that actually works as it should.
Thats called quality inconsistency. So what i said, are facts, not bashing.
I will just not participate longer.
/Bingo
Never get emotionally attached to a brand. Its just a cheap metal box. I have nothing against you or Qotom. I will continue to buy them and recommend them despite the issues i had with cheapest models. At the end, you get what you pay for.
