New Fiber install, fresh Pfsense install, only getting 20Mbps up/down

jddoxtator

So if I am correct in my understanding.... It sounds like I just need to make a VLAN based around the IP address in that ARP request.

I have two IP's

Sender IP address: 192.24.57.117

Target IP address: 192.24.57.1

Target has to be the gatway VLAN and I have to apply this to WAN device?

Oh, and the Calix device is the ISP router, so this was a captured broadcast from the ISP router. I'm guessing I caught the echo off the gateway because it wasn't plugged into any switch. It was a really fast port swap and I had the recorder going when I did it.

Did some more research, and the VLAN tag should be 57 based on the IP addresses I think.

stephenw10

Easy enough to test. Create a VLAN interface with ID 57 on the current WAN interface (ix3?). Then reassign WAN to be that new VLAN (ix3.57).

Steve

jddoxtator

@stephenw10
Tried that, but I think I am extrapolating the Tag ID wrong. as 57 did not work.

I think it is the 802.1Q number I am after. Which is 0xa5 or a5 hex / 165 decimal

stephenw10

Try that then. Where are you reading that from?

jddoxtator

@stephenw10

That was from the sub menus of DTP. It did not work unfortunately.

I also found Originating VLAN: 85 in PVST+ , but that did not work as well.

I am about to try PID: PVSTP+ (0x010b) or 267 dec.

Cool_Corona

I had the same issues on FTTH here in Switzerland.

It was the SFP+ when mounted in a switch. In a converter it didnt get an address and exposed th routers MAC to the ISP and everything worked perfectly.

jddoxtator

From what I understand by reading a description of Cisco's implementation of PVST+, DTP is part of the trunk that the routers use in their network. So we can safely ignore that.

STP seems to be the client side of the VLAN. This being the most important information I can find in STP protocol:

Originating VLAN (PVID): 85
Type: Originating VLAN (0x0000)
Length: 2
Originating VLAN: 85

By my understanding that should make the VLAN 85, but that doesn't work. So there is still something missing.

Cool_Corona

what brand are the ISP router?

jddoxtator

@cool_corona Calix

Cool_Corona

Have you told the support that you want to use your own router?

So they will release the MAC and let you do that?

jddoxtator

@cool_corona Yes, they wont allow it.

Cool_Corona

@jddoxtator Have you tried to spoof the mac of the org router?

jddoxtator

@cool_corona Yes, the spoof has been enabled since the start.

Cool_Corona

Are there any dip switches in the converter?

stephenw10

Ok, testing this locally I expect to be able to see the tagged traffic in the GUI packet capture if the view detail is set to full however there is some oddness there. I'm digging into that but it will show there if you do not filter like:

19:36:07.585799 90:ec:77:1f:8a:5f > ff:ff:ff:ff:ff:ff, ethertype 802.1Q (0x8100), length 46: vlan 229, p 0, ethertype ARP, Ethernet (len 6), IPv4 (len 4), Request who-has 10.229.5.10 tell 10.229.5.1, length 28

There is no question of which VLAN is in use there.

You can also run at the CLI something like:

tcpdump -nvve -i ix0

And you will see all the traffic on the interface including vlan tags.

Steve

jddoxtator

@stephenw10 Alright tried the console code and got a different VLAN again

15:21:32.364086 3c:ec:ef:70:19:a6 > ff:ff:ff:ff:ff:ff, ethertype 802.1Q (0x8100), length 346: vlan 1, p 0, ethertype IPv4, (tos 0x10, ttl 128, id 0, offset 0, flags [none], proto UDP (17), length 328)
    0.0.0.0.68 > 255.255.255.255.67: [udp sum ok] BOOTP/DHCP, Request from 3c:ec:ef:70:19:a6, length 300, xid 0xa6981c02, Flags [none] (0x0000)
          Client-Ethernet-Address 3c:ec:ef:70:19:a6
          Vendor-rfc1048 Extensions
            Magic Cookie 0x63825363
            DHCP-Message Option 53, length 1: Discover
            Client-ID Option 61, length 7: ether 3c:ec:ef:70:19:a6
            Hostname Option 12, length 7: "pfSense"
            Parameter-Request Option 55, length 10: 
              Subnet-Mask, BR, Time-Zone, Classless-Static-Route
              Default-Gateway, Domain-Name, Domain-Name-Server, Hostname
              Option 119, MTU
15:21:32.865804 10:f9:20:89:a0:f6 > 01:00:0c:cc:cc:cc, 802.3, length 40: LLC, dsap SNAP (0xaa) Individual, ssap SNAP (0xaa) Command, ctrl 0x03: oui Cisco (0x00000c), pid DTP (0x2004), length 38: DTPv1, length 38
        Domain TLV (0x0001) TLV, length 11, Packet
        Status TLV (0x0002) TLV, length 5, 0x81
        DTP type TLV (0x0003) TLV, length 5, 0xa5
        Neighbor TLV (0x0004) TLV, length 10, 10:f9:20:89:a0:f6
15:21:33.395704 3c:ec:ef:70:19:a6 > ff:ff:ff:ff:ff:ff, ethertype 802.1Q (0x8100), length 346: vlan 1, p 0, ethertype IPv4, (tos 0x10, ttl 128, id 0, offset 0, flags [none], proto UDP (17), length 328)
    0.0.0.0.68 > 255.255.255.255.67: [udp sum ok] BOOTP/DHCP, Request from 3c:ec:ef:70:19:a6, length 300, xid 0xa6981c02, secs 1, Flags [none] (0x0000)
          Client-Ethernet-Address 3c:ec:ef:70:19:a6
          Vendor-rfc1048 Extensions
            Magic Cookie 0x63825363
            DHCP-Message Option 53, length 1: Discover
            Client-ID Option 61, length 7: ether 3c:ec:ef:70:19:a6
            Hostname Option 12, length 7: "pfSense"
            Parameter-Request Option 55, length 10: 
              Subnet-Mask, BR, Time-Zone, Classless-Static-Route
              Default-Gateway, Domain-Name, Domain-Name-Server, Hostname
              Option 119, MTU
15:21:33.865863 10:f9:20:89:a0:f6 > 01:00:0c:cc:cc:cc, 802.3, length 40: LLC, dsap SNAP (0xaa) Individual, ssap SNAP (0xaa) Command, ctrl 0x03: oui Cisco (0x00000c), pid DTP (0x2004), length 38: DTPv1, length 38
        Domain TLV (0x0001) TLV, length 11, Packet
        Status TLV (0x0002) TLV, length 5, 0x81
        DTP type TLV (0x0003) TLV, length 5, 0xa5
        Neighbor TLV (0x0004) TLV, length 10, 10:f9:20:89:a0:f6
15:21:34.410039 3c:ec:ef:70:19:a6 > ff:ff:ff:ff:ff:ff, ethertype 802.1Q (0x8100), length 346: vlan 1, p 0, ethertype IPv4, (tos 0x10, ttl 128, id 0, offset 0, flags [none], proto UDP (17), length 328)
    0.0.0.0.68 > 255.255.255.255.67: [udp sum ok] BOOTP/DHCP, Request from 3c:ec:ef:70:19:a6, length 300, xid 0xa6981c02, secs 2, Flags [none] (0x0000)
          Client-Ethernet-Address 3c:ec:ef:70:19:a6
          Vendor-rfc1048 Extensions
            Magic Cookie 0x63825363
            DHCP-Message Option 53, length 1: Discover
            Client-ID Option 61, length 7: ether 3c:ec:ef:70:19:a6
            Hostname Option 12, length 7: "pfSense"
            Parameter-Request Option 55, length 10: 
              Subnet-Mask, BR, Time-Zone, Classless-Static-Route
              Default-Gateway, Domain-Name, Domain-Name-Server, Hostname
              Option 119, MTU
15:21:35.057589 3c:ec:ef:70:1c:f5 > ff:ff:ff:ff:ff:ff, ethertype IPv4 (0x0800), length 342: (tos 0x0, ttl 64, id 0, offset 0, flags [none], proto UDP (17), length 328)
    0.0.0.0.68 > 255.255.255.255.67: [udp sum ok] BOOTP/DHCP, Request from 3c:ec:ef:70:1c:f5, length 300, xid 0xc9c42930, Flags [none] (0x0000)
          Client-Ethernet-Address 3c:ec:ef:70:1c:f5
          Vendor-rfc1048 Extensions
            Magic Cookie 0x63825363
            DHCP-Message Option 53, length 1: Discover
            Client-ID Option 61, length 7: ether 3c:ec:ef:70:1c:f5
            MSZ Option 57, length 2: 576
            Parameter-Request Option 55, length 7: 
              Subnet-Mask, Default-Gateway, Domain-Name-Server, Hostname
              Domain-Name, BR, NTP
            Vendor-Class Option 60, length 12: "udhcp 1.23.1"
15:21:35.108688 10:f9:20:89:a0:f6 > 01:00:0c:cc:cc:cc, ethertype 802.1Q (0x8100), length 560: vlan 1, p 7, LLC, dsap SNAP (0xaa) Individual, ssap SNAP (0xaa) Command, ctrl 0x03: oui Cisco (0x00000c), pid CDP (0x2000), length 534: CDPv2, ttl: 180s, checksum: 0x72f9 (unverified), length 534
        Device-ID (0x01), value length: 32 bytes: 'MtBrydges-4507-2.nftctelecom.com'
        Version String (0x05), value length: 285 bytes: 
          Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch  Software (cat4500es8-UNIVERSALK9-M), Version 03.09.00.E RELEASE SOFTWARE (fc1)
          Technical Support: http://www.cisco.com/techsupport
          Copyright (c) 1986-2016 by Cisco Systems, Inc.
          Compiled Tue 19-Jul-16 12:34 by prod_rel_team
        Platform (0x06), value length: 17 bytes: 'cisco WS-C4507R+E'
        Address (0x02), value length: 13 bytes: IPv4 (1) 172.31.16.2
        Port-ID (0x03), value length: 19 bytes: 'GigabitEthernet6/15'
        Capability (0x04), value length: 4 bytes: (0x00000029): Router, L2 Switch, IGMP snooping
        Prefixes (0x07), value length: 10 bytes:  IPv4 Prefixes (2): 172.31.16.0/22 192.168.3.0/24
        VTP Management Domain (0x09), value length: 6 bytes: 'Packet'
        Native VLAN ID (0x0a), value length: 2 bytes: 85
        Duplex (0x0b), value length: 1 byte: full
        AVVID trust bitmap (0x12), value length: 1 byte: 0x00
        AVVID untrusted ports CoS (0x13), value length: 1 byte: 0x00
        Management Addresses (0x16), value length: 13 bytes: IPv4 (1) 172.31.16.2
        unknown field type (0x1a), value length: 12 bytes: 
          0x0000:  0000 0001 0000 0000 ffff ffff
        unknown field type (0x1b), value length: 1 byte: 
          0x0000:  00
        unknown field type (0x1f), value length: 1 byte: 
          0x0000:  00
        unknown field type (0x1005), value length: 20 bytes: 
          0x0000:  5753 2d58 3435 2d53 5550 382d 4500 2830
          0x0010:  2972 3f7c
        unknown field type (0x1004), value length: 15 bytes: 
          0x0000:  6530 3266 2e36 6461 352e 3136 3830 00
        unknown field type (0x1003), value length: 1 byte: 
          0x0000:  31

I copied everything from connection until response from a cisco router. I see VLAN 1 but I tried that and it gives me no IP. Same as any other VLAN I have tried.

stephenw10

That's after setting VLAN1? It looks like dhcp requests from pfSense tagged as that.

You might try switching the ISP router in and back out before the pcap to try to get some tagged traffic from the ISP as you did before with the ARP packet.

Ultimately the only way to know for sure is to setup a switch with a mirror port so you can capture exactly what the ISP router is doing.

The other thing is that you are almost certainly not the first person trying this. Someone else may have documented what's required for that ISP. Somewhere.

Steve

keyser

@jddoxtator To make this easy on yourself, try and connect a switch between the media converter and the original ISP router.
Connect your pfSense to one switchport and set its WAN port to either no IP address, or a fixed random private IP address.
Start a packet capture on WAN, and connect the ISP router to the switch.

When the ISP router is connected it will attempt to get a IP address via DHCP frames which is broadcasted - and include the VLAN tag the ISP router is using.
Those broadcasts should also reach your pfSense if the switch is a dumb non-managed Layer2 switch. If it is a smart VLAN capable/managed switch, this will not work, and you will have to setup a mirrorport/spanport on the switch which mirrors the ISP router port to your pfsense port.

jddoxtator

@stephenw10 Before setting VLAN 1

I set the pfsense router back to stock and switched the WAN port from the ISP router to the pfsense router after the ISP router had connected.

jddoxtator

Update: My old switch died, would not resolve DHCP anymore for some reason. Long story short, got a Cisco CBS220-24FP-4X capable of VLAN's and specifically PVST+

Some interesting behavior after getting this switch installed and running.

I set up a VLAN across one of the SFP 10Gbe ports and one of the copper 1Gbe ports. I then connected the fiber line directly to the switch SFP port and routers to the copper port.

Pfsense picked up the WAN signal and did it's usual thing connecting at 20Mb/s. However, the ISP router would not connect at all with the switch routing the fiber to the copper port on the VLAN.

There is something fundamentally different in how these two routers are connecting and I have no idea what.