Do either SFP modules offered work with the 6100?

mrsunfire

@stephenw10 OK I'll give it a go tomorrow asking my ISP to provision it for their GPON network.

mrsunfire

The modul supports "10/100/1000BaseX/SGMII LAN" SGMII LAN has to be 2.5G. Is this also supported with Netgate hardware? At the moment it shows 1000BASE-LX but maybe because it's not provisioned by ISP? My ISP is running GPON (2,5 gig down 1,5 gig up).

stephenw10

The module is effectively pretending to be a 1000base-LX device and the 6100 port has no problem with that. It's not possible to set it to 2.5G if that is required but it may not be. The module doesn't appear to support 2.5G at all though from the datasheet. At least not on the SFP side.
Unfortunately I simply have no way to test it.

Try running ifconfig -vvvm ix1 with the module inserted.

Steve

mrsunfire

This post is deleted!

mrsunfire

Modul is working now with my 500 MBit/s plan. It seems to not support 2,5G. Only thing confuses me is that I had to enable the ix1 interface (without setting IPv4 or IPv6 to anything other than disable) to get it to work. My ISP uses VLAN7 so I chose ix1.7 as PPPoE interface. If I'm not adding and enabling ix1 the PPPoE dialup doesn't work.

ix1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	description: SFP_FIBER
	options=8138b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER>
	capabilities=f53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,NETMAP,RXCSUM_IPV6,TXCSUM_IPV6>
	ether 90:ec:xx:xx:xx:xx
	inet6 fe80::xxxx:xxxx:xxxx:xxxx%ix1 prefixlen 64 scopeid 0x6
	media: Ethernet autoselect (Unknown)
	status: active
	supported media:
		media autoselect
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
	plugged: SFP/SFP+/SFP28 1000BASE-LX (SC)
	vendor: ZYXEL PN: PMG3000-D20B SN: xxxxxxxxxxxxx DATE: 2015-05-25
	module temperature: 52.85 C Voltage: 3.30 Volts
	RX: 0.04 mW (-13.77 dBm) TX: 2.00 mW (3.01 dBm

stephenw10

Hmm, interesting. I would have expected enabling ix1.7 to be sufficient.

Yes, there's no way to set that to 2.5G, it only supports autoselect. Though some ix cards have been shows to link at 2.5G I would not expect that to do so.

Steve

mrsunfire

@stephenw10 Got it working without ix1 interface. The "trick" was to not disable ix1 before deleting it. Leaving it enabled and deleting it works.

Ordered the Ubiquiti SFP+ modul to check if it's recognized by the 6100. Will keep you up to date.

EDIT: found out that I can set my SFP modul via CLI to 2.5G (HSGMII mode). But don't want to test it. Just for information.

stephenw10

As a media opt? What command are you using for that?

mrsunfire

@stephenw10 I'm SSH into it. Not via pfSense.

stephenw10

Like to the GPON module directly?

mrsunfire

@stephenw10 Exactly.

stephenw10

Ah, that's fun! Yeah if you set it to 2.5G I would not expect the ix port to see it as that. It might just connect anyway but if it doesn't how would you reset it to 1G? Unless it has a hardware reset maybe?

mrsunfire

@stephenw10 If it doesn't I have to put it into my Unifi switch. Unfortunately Amazon didn't deliver the 2.5G Ubiquiti module today so I have to wait until next week.

Florent PASCAL

Hi

@mrsunfire Did you try Ubiquiti SFP+ on your 6100 ? does it work at 2.5G ?

I also have a 6100 and try to make my ONT at 2.5G but it doesn't work I can't force the speed on pfsense. I tried to force my ONT on mode hsgmii ( fw_setenv sgmii_mode 5 ) with no success

My ONT works well at 2.5G on my switch mikrotik but I'm stuck at 1G on pfense.

Really annoying that we can't force speed on SFP+ ports on netgate 6100

mrsunfire

@florent-pascal No I didn't try. I'm back using my 2.5G RJ45 Modem provided by ISP for the moment.

aszajlai

@mrsunfire I was also able to get the Ubiquiti OM-MM-10G-D to work, I'm still setting up the 6100 to replace an 1100. I was able to verify that the FW is able to hot swap the modules with a ticket as the docs do not state either way. (https://docs.netgate.com/pfsense/en/latest/solutions/netgate-6100/io-ports.html#compatible-sfp-sfp-modules).

SoundCloud

This post is deleted!

aszajlai

@aszajlai - I have now been running this for two weeks with zero problems... Below are the stats, etc. Thank you everyone for this thread, now time for upgrading the other one that is no longer supported...

MTU:1500
Media: 10Gbase-SR <full-duplex,rxpause,txpause>
Plugged: SFP/SFP+/SFP28 10G Base-SR (LC)
Vendor:Ubiquiti Inc. PN: OM-MM-10G-D DATE: 2023-07-01
In/out packets: 22331704/27007819 (9.05 GiB/11.63 GiB)
In/out packets (pass): 22331704/27007819 (9.05 GiB/11.63 GiB)
In/out packets (block): 93141/0 (8.54 MiB/0 B)
In/out errors: 0/0
Collisions: 0
Interrupts: 44672451 (42/s)