Help - My firewall keeps crashing and I don't know why
-
Well, that didn't seem to work. Last night it crashed again. I attempted to get into the GUI, and it allowed me to sign in but then the webpage froze, and I had to pull the plug for a hard reboot. I have several text docs that I will try to upload when I make it to work and make sure all sensitive data is cleaned up from them.
-
When you say 'crashed' is it actually crashing? Do you see a crash report after rebooting?
Or does it just stop responding? Still active at the console?
-
@stephenw10 I got one when I did a Reroot of the system but when these glitches happen it does not seem to generate a report. It just kind of freezes and won't come back. Crashing might not be the correct term for it in the technical aspect. I have almost finished up with the logs I have and will be uploading what I have in a few.
Thank you for your continued help.
-
Were you able to confirm the alternative driver is loading from the boot log?
-
@stephenw10 I was not. I did my best to try and find it but unfortunately I was unable to confirm that it changed.
Here are the 4 files I have regarding the logs from the firewall.Routing Edited.txt info.0 General Edit.txt Gateways edit.txt
I will not be able to make it home till 6:30 Central Standard time to look at any information on the device as I do not have a way into it outside of my house.
Thank you,
Thomas Hook -
If the driver is loading the boot log should contain an entry like:
re0: version:1.97.00Your log doesn't appear to have that and the gateway issues coinside with the watchdog timeouts.
So I would make sure that driver is loading before doing anything else.
Steve
-
@stephenw10 Hello sir,
I will try and find the specified bit of information now. I did get a crash log today when I signed in.
-
That looks like a UFS issue, it's trying to remount after shutting down:
<118>pfSense is now shutting down ... <118> <6>pflog0: promiscuous mode disabled Trying to mount root from ufs:/dev/ufsid/628e817812c330cd [rw,noatime]... panic: vm_fault: fault on nofault entry, addr: 0xffffffff83d93000 cpuid = 2 time = 1673396073 KDB: enter: panicYou should run a filesystem check:
https://docs.netgate.com/pfsense/en/latest/troubleshooting/filesystem-check.html#manual-filesystem-checkYou can see from logs there though that it isn't running the alternative driver:
re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem 0xa1204000-0xa1204fff,0xa1200000-0xa1203fff at device 0.0 on pci1 re0: Using 1 MSI-X message re0: turning off MSI enable bit. re0: ASPM disabled re0: Chip rev. 0x4c000000 re0: MAC rev. 0x00000000Steve
-
@stephenw10 Hello sir,
Ran a reboot with file system check. attempted to do the driver install again and this is what I got. I do apologies as I am not that adept and linux based command line nor SSH The device is in a tricky spot due to space constraints and if I still am unable to get this to use the new driver I will have to try to take it down to do the single user file system check in the linked document.
-
Did you also run the lines to add the loader.conf.local values?
-
@stephenw10 Hello Sir,
I had to end up getting the device down and bringing it into my work and having my boss help me as I was unable to get the new driver loaded. He helped me with the command line and we believe that we finally have the driver installed. I will have to wait till I get home to see if the problem persists.
Thank you again for you time and help!
-
Hello Sir @stephenw10 After working with my boss at our office we were able to get in the commands to get the driver updated and I have not had a problem since. I will let you know if it fails again but for now the issues is resolved.
Thank you!
