Stuck at Marvell> after upgrade to pfSense Plus Software Version 23.01
-
Hi
After upgrading to pfSense Plus version 23.01, I'm stuck at the Marvel>. How do I recover?
My device is an SG-2100
Boot log:
code_text ```Marvell>> TIM-1.0 WTMI-devel-1.0.0-1115f12 WTMI: system early-init SVC REV: 5, CPU VDD voltage: 1.237V NOTICE: Booting Trusted Firmware NOTICE: BL1: v1.5(release):ROGUE2-01.00.00.01-cpu1_2G-0-g06b570a8d (Marvell-release-1.3.0) NOTICE: BL1: Built : 14:34:11, Feb 7 2020 NOTICE: BL1: Booting BL2 NOTICE: BL2: v1.5(release):ROGUE2-01.00.00.01-cpu1_2G-0-g06b570a8d (Marvell-release-1.3.0) NOTICE: BL2: Built : 14:34:13, Feb 7 2020 NOTICE: BL1: Booting BL31 NOTICE: BL31: v1.5(release):ROGUE2-01.00.00.01-cpu1_2G-0-g06b570a8d (Marvell-release-1.3.0) NOTICE: BL31: Built : 14 U-Boot 2018.03-devel-1.2.0ROGUE2-01.00.00.02+ (Feb 07 2020 - 14:33:22 -0500) Model: Silicom Rogue-2 CPU 1200 [MHz] L2 800 [MHz] TClock 200 [MHz] DDR 750 [MHz] DRAM: 3.4 GiB Comphy chip #0: Comphy-0: SGMII1 3.125 Gbps Comphy-1: PEX0 2.5 Gbps Comphy-2: SATA0 6 Gbps PCIE-0: Link down MMC: sdhci@d8000: 0 Loading Environment from SPI Flash... mvebu_spi_ofdata_to_platdata: ofdata clock 200000000, frequency 2000000 0 SF: Detected w25q32bv with page size 256 Bytes, erase size 4 KiB, total 4 MiB OK Model: Silicom Rogue-2 Net: eth0: neta@30000 [PRIME], eth1: neta@40000 Hit any key to stop autoboot: 0 Setting bus to 1 13323 armada-3720-sg1100.dtb 12948 armada-3720-sg2100.dtb 12948 armada-3720-netgate-2100.dtb 3 file(s), 0 dir(s) 12948 bytes read in 9 ms (1.4 MiB/s) 0 bytes read in 10 ms (0 Bytes/s) ## Starting EFI application at 01000000 ... Scanning disk sdhci@d8000.blk... Found 4 disks efi_load_pe: Invalid DOS Signature ## Application terminated, r = 9223372036854775806 Reset SCSI scanning bus for devices... ** Bad device scsi 0 ** resetting USB... USB0: Register 2000104 NbrPorts 2 Starting the controller USB XHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning bus 1 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found ** Bad device usb 0 ** BOOTP broadcast 1 DHCP client bound to address 45.51.108.225 (125 ms) *** Warning: no boot file name; using '2D336CE1.img' Using neta@30000 device TFTP from server 0.0.0.0; our IP address is 45.51.108.225; sending through gateway 45.51.104.1 Filename '2D336CE1.img'. Load address: 0x1000000 Loading: T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T Retry count exceeded; starting again *** ERROR: `serverip' not set *** ERROR: `serverip' not set ## Starting EFI application at 01000000 ... efi_load_pe: Invalid DOS Signature ## Application terminated, r = 9223372036854775806 Marvell>> -
@smk said in Stuck at Marvell> after upgrade to pfSense Plus Software Version 23.01:
efi_load_pe: Invalid DOS Signature
Seeing "Invalid DOS Signature" the last 48 hours on the forum.
-
@smk and https://redmine.pfsense.org/issues/13967
-
@steveits
Yeah ....
But was does that " .... No space left on device " actually mean ?
Upgrades were started with nearly no space left on the disk ? Serious ?
Or the path is wrong - as I have 'nothing' in /boot/efi/ ( a SG 4100 ) -
@gertjan I don’t know. Obviously not every upgrade or Netgate would have seen it. It’s the EFI partition though.
-
@steveits said in Stuck at Marvell> after upgrade to pfSense Plus Software Version 23.01:
It’s the EFI partition though.
Thanks, that was the info I was looking for.
-
Yes, that is what OP is hitting here.
If you haven't already open a ticket to get the recovery image:
https://www.netgate.com/tac-support-requestSteve
-
I have the same problem, luckily I use HA and the network is operating with the backup router, but it's situations like this that Netgate loses respect and credibility, launches an update version that doesn't work, feeling like they haven't even tested it , put it into production hoping it would work. And now who do I call Batman? Amateurs...
▒TIM-1.0 WTMI-devel-1.0.0-1115f12 WTMI: system early-init SVC REV: 5, CPU VDD voltage: 1.190V NOTICE: Booting Trusted Firmware NOTICE: BL1: v1.5(release):ROGUE2-01.00.00.01-cpu1_2G-0-g06b570a8d (Marvell-rel ease-1.3.0) NOTICE: BL1: Built : 14:34:11, Feb 7 2020 NOTICE: BL1: Booting BL2 NOTICE: BL2: v1.5(release):ROGUE2-01.00.00.01-cpu1_2G-0-g06b570a8d (Marvell-rel ease-1.3.0) NOTICE: BL2: Built : 14:34:13, Feb 7 2020 NOTICE: BL1: Booting BL31 NOTICE: BL31: v1.5(release):ROGUE2-01.00.00.01-cpu1_2G-0-g06b570a8d (Marvell-re lease-1.3.0) NOTICE: BL31: Built : 14 U-Boot 2018.03-devel-1.2.0ROGUE2-01.00.00.02+ (Feb 07 2020 - 14:33:22 -0500) Model: Silicom Rogue-2 CPU 1200 [MHz] L2 800 [MHz] TClock 200 [MHz] DDR 750 [MHz] DRAM: 3.4 GiB Comphy chip #0: Comphy-0: SGMII1 3.125 Gbps Comphy-1: PEX0 2.5 Gbps Comphy-2: SATA0 6 Gbps PCIE-0: Link down MMC: sdhci@d8000: 0 Loading Environment from SPI Flash... mvebu_spi_ofdata_to_platdata: ofdata clock 200000000, frequency 20000000 SF: Detected w25q32bv with page size 256 Bytes, erase size 4 KiB, total 4 MiB OK Model: Silicom Rogue-2 Net: eth0: neta@30000 [PRIME], eth1: neta@40000 Hit any key to stop autoboot: 0 Setting bus to 1 13323 armada-3720-sg1100.dtb 12948 armada-3720-sg2100.dtb 12948 armada-3720-netgate-2100.dtb 3 file(s), 0 dir(s) 12948 bytes read in 9 ms (1.4 MiB/s) 0 bytes read in 9 ms (0 Bytes/s) ## Starting EFI application at 01000000 ... Scanning disk sdhci@d8000.blk... Found 4 disks efi_load_pe: Invalid DOS Signature ## Application terminated, r = 9223372036854775806 Reset SCSI scanning bus for devices... ** Bad device scsi 0 ** resetting USB... USB0: Register 2000104 NbrPorts 2 Starting the controller USB XHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning bus 1 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found ** Bad device usb 0 ** BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.29.1.119 (1010 ms) *** Warning: no boot file name; using 'AC1D0177.img' Using neta@30000 device TFTP from server 0.0.0.0; our IP address is 172.29.1.119; sending through gateway 172.29.1.1 Filename 'AC1D0177.img'. Load address: 0x1000000 Loading: * TFTP error: 'File not found' (1) Not retrying... *** ERROR: `serverip' not set *** ERROR: `serverip' not set ## Starting EFI application at 01000000 ... efi_load_pe: Invalid DOS Signature ## Application terminated, r = 9223372036854775806 Marvell>> -
@m7infratec I actually just went through it so I know it's frustrating. But per other posts Netgate can't seem to replicate it, and obviously no one encountering it had installed the beta/RC. At least recovery isn't too bad, just need the image file and a 5GB+ USB stick.
