PFSense on Juniper SRX100 or SRX210 vpn router
-
Is it possible to install/run PFSense on this JunOS (FreeBSD based) router?
U-Boot 1.1.6 (Build time: Dec 12 2009 - 17:17:55) SRX_210_LOWMEM board revision major:0, minor:33, serial #: AAAM7655 OCTEON CN5020-SCP pass 1.1, Core clock: 400 MHz, DDR clock: 200 MHz (400 Mhz data rate) DRAM: 512 MB Starting Memory POST... Checking datalines... OK Checking address lines... OK Checking 512K memory for U-Boot... OK. Running U-Boot CRC Test... OK. Flash: 4 MB USB: scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Clearing DRAM....... done BIST check passed. Starting PCI PCI Status: PCI 32-bit PCI BAR 0: 0xf8000000, PCI BAR 1: Memory 0x00000000 PCI 0x00000000 Net: octeth0 POST Passed Press SPACE to abort autoboot in 1 seconds ELF file is 32 bit Loading .text @ 0x8f000078 (241008 bytes) Loading .rodata @ 0x8f03ade8 (13908 bytes) Loading .rodata.str1.4 @ 0x8f03e43c (15972 bytes) Loading set_Xcommand_set @ 0x8f0422a0 (96 bytes) Loading .rodata.cst4 @ 0x8f042300 (20 bytes) Loading .data @ 0x8f043000 (5572 bytes) Loading .data.rel.ro @ 0x8f0445c4 (120 bytes) Loading .data.rel @ 0x8f04463c (136 bytes) Clearing .bss @ 0x8f0446c8 (8304 bytes) ## Starting application at 0x8f000078 ... Consoles: U-Boot console Found compatible API, ver. 1.6 FreeBSD/MIPS U-Boot bootstrap loader, Revision 1.6 (builder@ormonth.juniper.net, Sat Dec 12 15:59:41 UTC 2009) Memory: 512MB [0]Booting from nand-flash slice 1 Un-Protected 1 sectors writing to flash... Protected 1 sectors Loading /boot/defaults/loader.conf /kernel data=0xb16d5c+0x134b2c syms=[0x4+0x8bbd0+0x4+0xcadc3] Hit [Enter] to boot immediately, or space bar for command prompt. Booting [/kernel]... Kernel entry at 0x801000e0 ... init regular console Primary ICache: Sets 64 Size 128 Asso 4 Primary DCache: Sets 1 Size 128 Asso 64 Secondary DCache: Sets 128 Size 128 Asso 8 GDB: debug ports: uart GDB: current port: uart KDB: debugger backends: ddb gdb KDB: current backend: ddb kld_map_v: 0x8ff80000, kld_map_p: 0x0 Copyright (c) 1996-2016, Juniper Networks, Inc. All rights reserved. Copyright (c) 1992-2006 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. JUNOS 12.1X46-D55.3 #0: 2016-07-08 18:46:54 UTC builder@quoarth.juniper.net:/volume/build/junos/12.1/service/12.1X46-D55.3/obj-octeon/junos/bsd/kernels/JSRXNLE/kernel JUNOS 12.1X46-D55.3 #0: 2016-07-08 18:46:54 UTC builder@quoarth.juniper.net:/volume/build/junos/12.1/service/12.1X46-D55.3/obj-octeon/junos/bsd/kernels/JSRXNLE/kernel real memory = 536870912 (512MB) avail memory = 308387840 (294MB) FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs Security policy loaded: JUNOS MAC/pcap (mac_pcap) Security policy loaded: JUNOS MAC/runasnonroot (mac_runasnonroot) netisr_init: !debug_mpsafenet, forcing maxthreads from 2 to 1 cpu0 on motherboard : CAVIUM's OCTEON 5020 CPU Rev. 0.1 with no FPU implemented L1 Cache: I size 32kb(128 line), D size 8kb(128 line), sixty four way. L2 Cache: Size 128kb, 8 way obio0 on motherboard uart0: <octeon-16550 0="" channel="">on obio0 uart0: console (9600,n,8,1) twsi0 on obio0 dwc0: <synopsis dwc="" otg="" controller="" driver="">on obio0 usb0: <usb bus="" for="" dwc="" otg="" controller="">on dwc0 usb0: USB revision 2.0 uhub0: vendor 0x0000 DWC OTG root hub, class 9/0, rev 2.00/1.00, addr 1 uhub0: 1 port with 1 removable, self powered uhub1: vendor 0x0409 product 0x005a, class 9/0, rev 2.00/1.00, addr 2 uhub1: single transaction translator uhub1: 3 ports with 2 removable, self powered umass0: STMicroelectronics ST72682 High Speed Mode, rev 2.00/2.10, addr 3 cpld0 on obio0 pcib0: <cavium on-chip="" pci="" bridge="">on obio0 Disabling Octeon big bar support PCI Status: PCI 32-bit: 0xc041b pcib0: Initialized controller pci0: <pci bus="">on pcib0 pci0: <serial bus,="" usb="">at device 2.0 (no driver attached) pci0: <serial bus,="" usb="">at device 2.2 (no driver attached) gblmem0 on obio0 octpkt0: <octeon rgmii="">on obio0 cfi0: <amd fujitsu="" -="" 4mb="">on obio0 Timecounter "mips" frequency 400000000 Hz quality 0 ###PCB Group initialized for udppcbgroup ###PCB Group initialized for tcppcbgroup da0 at umass-sim0 bus 0 target 0 lun 0 da0: <st st72682="" 2.10="">Removable Direct Access SCSI-2 device da0: 40.000MB/s transfers da0: 1000MB (2048000 512 byte sectors: 64H 32S/T 1000C) Trying to mount root from ufs:/dev/da0s1a MFSINIT: Initialising MFSROOT Process-1 beginning MFSROOT initialization... Creating MFSROOT... /dev/md0: 20.0MB (40956 sectors) block size 16384, fragment size 2048 using 4 cylinder groups of 5.00MB, 320 blks, 640 inodes. super-block backups (for fsck -b #) at: 32, 10272, 20512, 30752 Populating MFSROOT... Creating symlinks... Setting up mounts... Continuing boot from MFSROOT... Attaching /cf/packages/junos via /dev/mdctl... Mounted junos package on /dev/md1... D Media check on da0 Automatic reboot in progress... ** /dev/da0s1a (NO WRITE) ** Last Mounted on / ** Root file system ** Phase 1 - Check Blocks and Sizes ** Phase 2 - Check Pathnames ** Phase 3 - Check Connectivity ** Phase 4 - Check Reference Counts ** Phase 5 - Check Cyl groups 161 files, 75562 used, 73964 free (44 frags, 9240 blocks, 0.0% fragmentation) mount reload of '/' failed: Operation not supported Verified junos signed by PackageProductionEc_2016 method ECDSA Verified jboot signed by PackageProductionEc_2016 method ECDSA Verified junos-12.1X46-D55.3-domestic signed by PackageProductionEc_2016 method ECDSA Checking integrity of BSD labels: s1: Passed s2: Passed s3: Passed s4: Passed ** /dev/bo0s3e FILE SYSTEM CLEAN; SKIPPING CHECKS clean, 12428 free (28 frags, 1550 blocks, 0.2% fragmentation) ** /dev/bo0s3f FILE SYSTEM CLEAN; SKIPPING CHECKS clean, 172274 free (98 frags, 21522 blocks, 0.1% fragmentation) Checking integrity of licenses: Checking integrity of configuration: rescue.conf.gz: No recovery data Loading configuration ... Time and ticks drifted too much, resetting synchronization... mgd: commit complete Setting initial options: . Starting optional daemons: usbd. Doing initial network setup: . Initial interface configuration: additional daemons: eventd. Additional routing options:kern.module_path: /boot//kernel;/boot/modules -> /boot/modules;/modules/ifpfe_drv;/modules; kld netpfe drv: ifpfed_dialer ipsec kld. Doing additional network setup:. Starting final network daemons:. setting ldconfig path: /usr/lib /opt/lib starting standard daemons: cron. Initial rc.mips initialization:. Local package initialization:. starting local daemons:set cores for group access . kern.securelevel: -1 -> 1 Creating JAIL MFS partition... JAIL MFS partition created boot.upgrade.uboot="0xBFC00000" boot.upgrade.loader="0xBFE00000" Boot media /dev/da0 has dual root support ** /dev/da0s2a FILE SYSTEM CLEAN; SKIPPING CHECKS clean, 74476 free (28 frags, 9306 blocks, 0.0% fragmentation) Thu Dec 8 20:48:30 UTC 2016 Amnesiac (ttyu0) login:</st></amd></octeon></serial></serial></pci></cavium></usb></synopsis></octeon-16550>
-
It's MIPS, so no.