Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    pfSense on Watchguard M270

    Scheduled Pinned Locked Moved Hardware
    133 Posts 18 Posters 42.9k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • stephenw10S
      stephenw10 Netgate Administrator
      last edited by stephenw10

      The script looks like this:

      #!/bin/sh
#
# Script to setup the switch in the M270
#
# SteveW 5/6/2020
#

echo "Configuring switch..."
logger Configuring switch...

etherswitchcfg vlangroup1 vlan 1 members 9
etherswitchcfg vlangroup2 vlan 2 members 3,4,5,6,7,8,10
etherswitchcfg vlangroup3 vlan 3 members 2,4,5,6,7,8,10
etherswitchcfg vlangroup4 vlan 4 members 2,3,5,6,7,8,10
etherswitchcfg vlangroup5 vlan 5 members 2,3,4,6,7,8,10
etherswitchcfg vlangroup6 vlan 6 members 2,3,4,5,7,8,10
etherswitchcfg vlangroup7 vlan 7 members 2,3,4,5,6,8,10
etherswitchcfg vlangroup8 vlan 8 members 2,3,4,5,6,7,10
etherswitchcfg vlangroup9 vlan 9 members 1
etherswitchcfg vlangroup10 vlan 10 members 2,3,4,5,6,7,8

etherswitchcfg port1 forwarding
etherswitchcfg port2 forwarding
etherswitchcfg port3 forwarding
etherswitchcfg port4 forwarding
etherswitchcfg port5 forwarding
etherswitchcfg port6 forwarding
etherswitchcfg port7 forwarding
etherswitchcfg port8 forwarding
etherswitchcfg port9 forwarding
etherswitchcfg port10 forwarding

echo "done"
logger done

      But it will only run in Plus. None of the switch stuff is in CE.
      It's still not really perfect there. The required loader hints are lost at upgrade currently.

      Steve

      1 Reply Last reply Reply Quote 1
      • O
        ozon08
        last edited by

        Hey, i bought a Watchgaurd M270 and installed pfsense on a new mSata drive, activated pfsense plus home.
        After i stick it in the M270, it boots up but ich can not config the etherswitch.
        I get this error:

        etherswitchcfg: Can't open control file: /dev/etherswitch0: No such file or directory

        stephenw10S 1 Reply Last reply Reply Quote 0
        • stephenw10S
          stephenw10 Netgate Administrator @ozon08
          last edited by stephenw10

          You need the loader hints to create the switch device. Add these lines to /boot/device.hints:

          hint.mdio.0.at="ix1"
hint.e6000sw.0.addr=0
hint.e6000sw.0.is6190=1
hint.e6000sw.0.port0disabled=1
hint.e6000sw.0.port9cpu=1
hint.e6000sw.0.port10cpu=1
hint.e6000sw.0.port9speed=2500
hint.e6000sw.0.port10speed=2500

          Unfortunately as I said those are lost at upgrade. The file handling for the 7100 switch adds/removes those lines when needed and the m270 is not recognised. Been a while since I looked at it though. Might be different in 22.01.
          Edit: Nope still removed at upgrade so you need console access to add it back.

          Steve

          O 1 Reply Last reply Reply Quote 1
          • O
            ozon08 @stephenw10
            last edited by

            @stephenw10 thank you.
            My Switch is now working, but is ix1 wan and lan port or is ix0 wan and ix1 lan?

            stephenw10S 1 Reply Last reply Reply Quote 0
            • stephenw10S
              stephenw10 Netgate Administrator @ozon08
              last edited by

              If you used the script I posted above WAN should be ix0 and connects to port 0.
              LAN should be ix1 and connects to ports 1-7.

              Of course you can change that to be however you want. Add VLANs to get 8 separate interfaces/ports for example.

              Steve

              O 1 Reply Last reply Reply Quote 1
              • S
                sorcefm
                last edited by

                This post is deleted!
                1 Reply Last reply Reply Quote 0
                • S
                  sorcefm
                  last edited by

                  This post is deleted!
                  1 Reply Last reply Reply Quote 0
                  • O
                    ozon08 @stephenw10
                    last edited by

                    @stephenw10 Perfect. Now everything is running.
                    Thank you very much Steve

                    O 1 Reply Last reply Reply Quote 1
                    • O
                      ozon08 @ozon08
                      last edited by ozon08

                      Did anyone update to pfsense plus 23.x?
                      @stephenw10 can you help me?

                      1 Reply Last reply Reply Quote 0
                      • stephenw10S
                        stephenw10 Netgate Administrator
                        last edited by

                        It will run 23.01 just fine but, as mentioned, the device hints required for the switch will be lost at upgrade.
                        You will need to add them back at the console after the reboot. That might be twice coming from 22.05.

                        Steve

                        O 1 Reply Last reply Reply Quote 0
                        • O
                          ozon08 @stephenw10
                          last edited by

                          @stephenw10 i did this with the hints and the etherswitch config but it didnt work. The Links are up but no connection to the network

                          1 Reply Last reply Reply Quote 0
                          • stephenw10S
                            stephenw10 Netgate Administrator
                            last edited by

                            Also this applies as it's the same switch: https://redmine.pfsense.org/issues/13993
                            Unlikely you would hit it unless you have two in HA with a direct link.

                            1 Reply Last reply Reply Quote 0
                            • stephenw10S
                              stephenw10 Netgate Administrator
                              last edited by

                              Check etherswitchcfg shows the correct switch config.

                              O 1 Reply Last reply Reply Quote 0
                              • O
                                ozon08 @stephenw10
                                last edited by

                                @stephenw10 what show etherswichcfg show me?

                                1 Reply Last reply Reply Quote 0
                                • stephenw10S
                                  stephenw10 Netgate Administrator
                                  last edited by

                                  It should show you the current config for the switch.
                                  If it just errors then the switch hasn't been setup correctly.
                                  If it shows something but it's incorrect then the switch setup script probably didn't get run by the shellcmd.

                                  The actual output depends how you have it setup.

                                  O 1 Reply Last reply Reply Quote 0
                                  • O
                                    ozon08 @stephenw10
                                    last edited by

                                    @stephenw10 port9 and port10 is in state 1. is it correct?

                                    1 Reply Last reply Reply Quote 0
                                    • stephenw10S
                                      stephenw10 Netgate Administrator
                                      last edited by

                                      If you're using my example script above where the WAN is port 1 and LAN is ports 2-8 then it should look like:

                                      [23.01-RELEASE][root@m270-2.stevew.lan]/root: etherswitchcfg
etherswitch0: VLAN mode: PORT
port1:
        state=8<FORWARDING>
        flags=0<>
        media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active
port2:
        state=8<FORWARDING>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port3:
        state=8<FORWARDING>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port4:
        state=8<FORWARDING>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port5:
        state=8<FORWARDING>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port6:
        state=8<FORWARDING>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port7:
        state=8<FORWARDING>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port8:
        state=8<FORWARDING>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port9:
        state=8<FORWARDING>
        flags=1<CPUPORT>
        media: Ethernet 2500Base-KX <full-duplex>
        status: active
port10:
        state=8<FORWARDING>
        flags=1<CPUPORT>
        media: Ethernet 2500Base-KX <full-duplex>
        status: active
vlangroup1:
        port: 1
        members 9
vlangroup2:
        port: 2
        members 3,4,5,6,7,8,10
vlangroup3:
        port: 3
        members 2,4,5,6,7,8,10
vlangroup4:
        port: 4
        members 2,3,5,6,7,8,10
vlangroup5:
        port: 5
        members 2,3,4,6,7,8,10
vlangroup6:
        port: 6
        members 2,3,4,5,7,8,10
vlangroup7:
        port: 7
        members 2,3,4,5,6,8,10
vlangroup8:
        port: 8
        members 2,3,4,5,6,7,10
vlangroup9:
        port: 9
        members 1
vlangroup10:
        port: 10
        members 2,3,4,5,6,7,8
                                      1 Reply Last reply Reply Quote 0
                                      • stephenw10S
                                        stephenw10 Netgate Administrator
                                        last edited by

                                        Ah, now I recall I had to add those ports to the script in 23.01!

                                        #!/bin/sh
#
# Script to setup the switch in the M270
#
# SteveW 5/6/2020
#

echo "Configuring switch..."
logger Configuring switch...

etherswitchcfg vlangroup1 vlan 1 members 9
etherswitchcfg vlangroup2 vlan 2 members 3,4,5,6,7,8,10
etherswitchcfg vlangroup3 vlan 3 members 2,4,5,6,7,8,10
etherswitchcfg vlangroup4 vlan 4 members 2,3,5,6,7,8,10
etherswitchcfg vlangroup5 vlan 5 members 2,3,4,6,7,8,10
etherswitchcfg vlangroup6 vlan 6 members 2,3,4,5,7,8,10
etherswitchcfg vlangroup7 vlan 7 members 2,3,4,5,6,8,10
etherswitchcfg vlangroup8 vlan 8 members 2,3,4,5,6,7,10
etherswitchcfg vlangroup9 vlan 9 members 1
etherswitchcfg vlangroup10 vlan 10 members 2,3,4,5,6,7,8

etherswitchcfg port1 forwarding
etherswitchcfg port2 forwarding
etherswitchcfg port3 forwarding
etherswitchcfg port4 forwarding
etherswitchcfg port5 forwarding
etherswitchcfg port6 forwarding
etherswitchcfg port7 forwarding
etherswitchcfg port8 forwarding
etherswitchcfg port9 forwarding
etherswitchcfg port10 forwarding

echo "done"
logger done
                                        O 1 Reply Last reply Reply Quote 0
                                        • O
                                          ozon08 @stephenw10
                                          last edited by

                                          @stephenw10 this looks like my configuration.

                                          1 Reply Last reply Reply Quote 0
                                          • O
                                            ozon08
                                            last edited by

                                            @stephenw10 i just have it. I forgot to forward port 9 and 10. sorry that was my fault

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.