Stuck In Marvel U-Boot

[haroonkhan1722]

Dear Support,
By mistake i upload wrong xml file in my firewall (SG-3100)
after installing xml i lose acess on gui and when i acess by serial its stuck in marvell how can i make reset to factory setting,
Waiting for your reply,
@stephenw10

[haroonkhan1722]

__   __                      _ _
|  \/  | __ _ _ ____   _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| |  | | (_| | |   \ V /  __/ | |
|_|  |_|\__,_|_|    \_/ \___|_|_|
         _   _     ____              _
        | | | |   | __ )  ___   ___ | |_
        | | | |___|  _ \ / _ \ / _ \| __|
        | |_| |___| |_) | (_) | (_) | |_
         \___/    |____/ \___/ \___/ \__|
 ** LOADER **


U-Boot 2013.01-02879-geb5cbf6642 (Oct 08 2018 - 12:59:19) Marvell version: devel                                                                                        -17.06.0

Board: Rogue-1
SoC:   MV88F6820 Rev A0
       running 2 CPUs
CPU:   ARM Cortex A9 MPCore (Rev 1) LE
       CPU 0
       CPU    @ 1600 [MHz]
       L2     @ 800 [MHz]
       TClock @ 250 [MHz]
       DDR4    @ 800 [MHz]
       DDR4 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM:  2 GiB
MMC:   mv_sdh: 0
DBG: Calling spi_flash_probe from env_relocate_spec()
SF: Probing bus 0 cs 0 @ 20000000Hz mode 3
SF: Detected W25Q32JV with page size 4 KiB, total 4 MiB
PCI-e 0: Detected No Link.
PCI-e 1: Detected No Link.
USB2.0 0: Host Mode
USB3.0 1: Host Mode

Map:   Code:                    0x7fedc000:0x7ff9741c
       BSS:                     0x7ffef600
       Stack:                   0x7f4cbf20
       Heap:                    0x7f4cc000:0x7fedc000
       U-Boot Environment:      0x00100000:0x00110000 (SPI)

Board configuration detected:
Net:
|  port  | Interface | PHY address  |
|--------|-----------|--------------|
| egiga0 |   RGMII   |     0x00     |
| egiga1 |   RGMII   |     0x01     |
| egiga2 |   SGMII   |   In-Band    |
egiga0 [PRIME], egiga1, egiga2
Hit any key to stop autoboot:  0
Marvell>>
Marvell>>

[haroonkhan1722]

🔒 Log in to view

🔒 Log in to view

[haroonkhan1722]

and When iam trying recovery image its stoping here as you can see in below note:

This will install the standard firmware and will erase all the existing
contents of the destination device permanently.

eMMC device: mmcsd0

M.2 device: ada0

Type the name of the destination device (mmcsd0,ada0) or press the Enter key to install on mmcsd0: ada0

Selected M.2 device: ada0

Are you sure you want to continue ? (y/N) y

Erasing the M.2 contents...
Writing the firmware to M.2...
(this may take a few minutes to complete)
0+32768 records in
512+0 records out
2147483648 bytes transferred in 37.894049 secs (56670736 bytes/sec)
Fixing M.2 labels...
Fixing u-boot environment...
dd: /dev/flash/spi0: No such file or directory
Invalid input file: /root/env
stat: No such file or directory
Invalid input file: /root/newenv
stat: No such file or directory

Done!

The system will halt now, please power off and remove the firmware
recovery storage device.

Shutdown NOW!
shutdown: [pid 1145]

FreeBSD/arm (3100-recovery) (Stopping cron.
Waiting for PIDS: 1081.
Stopping devd.
Waiting for PIDS: 848.
Writing entropy file: .
Writing early boot entropy file: .
Terminated
.
Mar 16 06:40:47 3100-recovery syslogd: exiting on signal 15
Waiting (max 60 seconds) for system process vnlru' to stop... done Waiting (max 60 seconds) for system process syncer' to stop...
Syncing disks, vnodes remaining... 1 0 done
All buffers synced.
Uptime: 1m37s

The operating system has halted.
Power cycle or reset to reboot.

After i do reboot it come to marvel again can you check if you want remote access i can give you too

[Gertjan]

@haroonkhan1722 said in Stuck In Marvel U-Boot:

After i do reboot

You've removed the USB stick at that moment, right ?

[stephenw10]

At the Marvell prompt enter: printenv bootcmd

Marvell>> printenv bootcmd
bootcmd=run setLED; run m2boot;

It should be that if you're booting from m.2.

Steve

[haroonkhan1722]

Hi,
yes after executing these below commands it starts working.

setenv bootcmd 'run setLED; run m2boot;'
saveenv
run m2boot

Thanks

[rrocha]

@haroonkhan1722 said in Stuck In Marvel U-Boot:

yes after executing these below commands it starts working.

Hi,
To original SG-3100 storage execute these bellow commands.

setenv bootcmd 'setLED; run emmcboot;'
saveenv
run emmcboot

[stephenw10]

@rrocha said in Stuck In Marvel U-Boot:

setenv bootcmd 'setLED; run emmcboot;'

You need another 'run' in there like:
setenv bootcmd 'run setLED; run emmcboot;'