Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    pfSense on Watchguard M270

    Hardware
    18
    133
    32.3k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • stephenw10S
      stephenw10 Netgate Administrator
      last edited by

      It should show you the current config for the switch.
      If it just errors then the switch hasn't been setup correctly.
      If it shows something but it's incorrect then the switch setup script probably didn't get run by the shellcmd.

      The actual output depends how you have it setup.

      O 1 Reply Last reply Reply Quote 0
      • O
        ozon08 @stephenw10
        last edited by

        @stephenw10 port9 and port10 is in state 1. is it correct?

        1 Reply Last reply Reply Quote 0
        • stephenw10S
          stephenw10 Netgate Administrator
          last edited by

          If you're using my example script above where the WAN is port 1 and LAN is ports 2-8 then it should look like:

          [23.01-RELEASE][root@m270-2.stevew.lan]/root: etherswitchcfg
          etherswitch0: VLAN mode: PORT
          port1:
                  state=8<FORWARDING>
                  flags=0<>
                  media: Ethernet autoselect (1000baseT <full-duplex>)
                  status: active
          port2:
                  state=8<FORWARDING>
                  flags=0<>
                  media: Ethernet autoselect (none)
                  status: no carrier
          port3:
                  state=8<FORWARDING>
                  flags=0<>
                  media: Ethernet autoselect (none)
                  status: no carrier
          port4:
                  state=8<FORWARDING>
                  flags=0<>
                  media: Ethernet autoselect (none)
                  status: no carrier
          port5:
                  state=8<FORWARDING>
                  flags=0<>
                  media: Ethernet autoselect (none)
                  status: no carrier
          port6:
                  state=8<FORWARDING>
                  flags=0<>
                  media: Ethernet autoselect (none)
                  status: no carrier
          port7:
                  state=8<FORWARDING>
                  flags=0<>
                  media: Ethernet autoselect (none)
                  status: no carrier
          port8:
                  state=8<FORWARDING>
                  flags=0<>
                  media: Ethernet autoselect (none)
                  status: no carrier
          port9:
                  state=8<FORWARDING>
                  flags=1<CPUPORT>
                  media: Ethernet 2500Base-KX <full-duplex>
                  status: active
          port10:
                  state=8<FORWARDING>
                  flags=1<CPUPORT>
                  media: Ethernet 2500Base-KX <full-duplex>
                  status: active
          vlangroup1:
                  port: 1
                  members 9
          vlangroup2:
                  port: 2
                  members 3,4,5,6,7,8,10
          vlangroup3:
                  port: 3
                  members 2,4,5,6,7,8,10
          vlangroup4:
                  port: 4
                  members 2,3,5,6,7,8,10
          vlangroup5:
                  port: 5
                  members 2,3,4,6,7,8,10
          vlangroup6:
                  port: 6
                  members 2,3,4,5,7,8,10
          vlangroup7:
                  port: 7
                  members 2,3,4,5,6,8,10
          vlangroup8:
                  port: 8
                  members 2,3,4,5,6,7,10
          vlangroup9:
                  port: 9
                  members 1
          vlangroup10:
                  port: 10
                  members 2,3,4,5,6,7,8
          
          1 Reply Last reply Reply Quote 0
          • stephenw10S
            stephenw10 Netgate Administrator
            last edited by

            Ah, now I recall I had to add those ports to the script in 23.01!

            #!/bin/sh
            #
            # Script to setup the switch in the M270
            #
            # SteveW 5/6/2020
            #
            
            echo "Configuring switch..."
            logger Configuring switch...
            
            etherswitchcfg vlangroup1 vlan 1 members 9
            etherswitchcfg vlangroup2 vlan 2 members 3,4,5,6,7,8,10
            etherswitchcfg vlangroup3 vlan 3 members 2,4,5,6,7,8,10
            etherswitchcfg vlangroup4 vlan 4 members 2,3,5,6,7,8,10
            etherswitchcfg vlangroup5 vlan 5 members 2,3,4,6,7,8,10
            etherswitchcfg vlangroup6 vlan 6 members 2,3,4,5,7,8,10
            etherswitchcfg vlangroup7 vlan 7 members 2,3,4,5,6,8,10
            etherswitchcfg vlangroup8 vlan 8 members 2,3,4,5,6,7,10
            etherswitchcfg vlangroup9 vlan 9 members 1
            etherswitchcfg vlangroup10 vlan 10 members 2,3,4,5,6,7,8
            
            etherswitchcfg port1 forwarding
            etherswitchcfg port2 forwarding
            etherswitchcfg port3 forwarding
            etherswitchcfg port4 forwarding
            etherswitchcfg port5 forwarding
            etherswitchcfg port6 forwarding
            etherswitchcfg port7 forwarding
            etherswitchcfg port8 forwarding
            etherswitchcfg port9 forwarding
            etherswitchcfg port10 forwarding
            
            echo "done"
            logger done
            
            O 1 Reply Last reply Reply Quote 0
            • O
              ozon08 @stephenw10
              last edited by

              @stephenw10 this looks like my configuration.

              1 Reply Last reply Reply Quote 0
              • O
                ozon08
                last edited by

                @stephenw10 i just have it. I forgot to forward port 9 and 10. sorry that was my fault

                1 Reply Last reply Reply Quote 0
                • stephenw10S
                  stephenw10 Netgate Administrator
                  last edited by

                  No that wasn't required in 22.05. Something changed in the switch driver defaults. Probably the same reason for that MDI/X bug.

                  O 1 Reply Last reply Reply Quote 0
                  • O
                    ozon08 @stephenw10
                    last edited by

                    @stephenw10 okay, now i added it to my shellcmd. After a test reboot it works fine. Thank you

                    1 Reply Last reply Reply Quote 1
                    • S
                      shaker
                      last edited by

                      Hello,
                      I tried the whole night to bring me M270 to work.
                      But I didn't have success.

                      Can you please explain more detailed, what are the steps for get it done?

                      Thank you so much.

                      O 1 Reply Last reply Reply Quote 0
                      • O
                        ozon08 @shaker
                        last edited by

                        @shaker
                        What have you done so far?

                        1 Reply Last reply Reply Quote 0
                        • S
                          shaker
                          last edited by

                          I installed OPNsense, which is very similar to pfSense without issues. The switchports are not able to work by default.
                          Then I opened "shell" to modify the files you recommended.

                          First I added this code

                          hint.mdio.0.at="ix1"
                          hint.e6000sw.0.addr=0
                          hint.e6000sw.0.is6190=1
                          hint.e6000sw.0.port0disabled=1
                          hint.e6000sw.0.port9cpu=1
                          hint.e6000sw.0.port10cpu=1
                          hint.e6000sw.0.port9speed=2500
                          hint.e6000sw.0.port10speed=2500
                          

                          to /boot/device.hints

                          Then I created the scripts in /usr/local/bin/setup_switch.sh

                          #!/bin/sh
                          #
                          # Script to setup the switch in the M270
                          #
                          # SteveW 5/6/2020
                          #
                          
                          echo "Configuring switch..."
                          logger Configuring switch...
                          
                          etherswitchcfg vlangroup1 vlan 1 members 9
                          etherswitchcfg vlangroup2 vlan 2 members 3,4,5,6,7,8,10
                          etherswitchcfg vlangroup3 vlan 3 members 2,4,5,6,7,8,10
                          etherswitchcfg vlangroup4 vlan 4 members 2,3,5,6,7,8,10
                          etherswitchcfg vlangroup5 vlan 5 members 2,3,4,6,7,8,10
                          etherswitchcfg vlangroup6 vlan 6 members 2,3,4,5,7,8,10
                          etherswitchcfg vlangroup7 vlan 7 members 2,3,4,5,6,8,10
                          etherswitchcfg vlangroup8 vlan 8 members 2,3,4,5,6,7,10
                          etherswitchcfg vlangroup9 vlan 9 members 1
                          etherswitchcfg vlangroup10 vlan 10 members 2,3,4,5,6,7,8
                          
                          etherswitchcfg port1 forwarding
                          etherswitchcfg port2 forwarding
                          etherswitchcfg port3 forwarding
                          etherswitchcfg port4 forwarding
                          etherswitchcfg port5 forwarding
                          etherswitchcfg port6 forwarding
                          etherswitchcfg port7 forwarding
                          etherswitchcfg port8 forwarding
                          
                          echo "done"
                          logger done
                          

                          Gave it this:
                          chmod +x setup_switch.sh

                          run it ./setup_switch.sh

                          But I get fault:

                          etherswitchcfg: Can't open control file: /dev/etherswitch0: No such file or directory
                          

                          More Information:

                          root@OPNsense:/ # kldstat
                          Id Refs Address                Size Name
                           1   39 0xffffffff80200000  215dc08 kernel
                           2    1 0xffffffff8235e000     f460 carp.ko
                           3    1 0xffffffff8236e000     3b18 pflog.ko
                           4    3 0xffffffff82372000    75240 pf.ko
                           6    1 0xffffffff82407000    3d648 if_ixv.ko
                           7    1 0xffffffff82445000    4f610 if_ix.ko
                           8    1 0xffffffff82495000     4b58 if_enc.ko
                           9    1 0xffffffff8249a000     ba48 if_gre.ko
                          10    1 0xffffffff824a6000    18338 if_lagg.ko
                          11    2 0xffffffff824bf000     3538 if_infiniband.ko
                          12    1 0xffffffff824c3000     e4d0 if_bridge.ko
                          13    2 0xffffffff824d2000     7870 bridgestp.ko
                          14    1 0xffffffff824da000     e318 pfsync.ko
                          15    1 0xffffffff82720000     3250 ichsmb.ko
                          16    1 0xffffffff82724000     2180 smbus.ko
                          17    1 0xffffffff82727000     4700 nullfs.ko
                          
                          root@OPNsense:/ # ifconfig -a
                          ix0: flags=8863<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
                                  description: WAN (wan)
                                  options=4803828<VLAN_MTU,JUMBO_MTU,WOL_UCAST,WOL_MCAST,WOL_MAGIC,NOMAP>
                                  ether 00:a0:c9:00:00:02
                                  media: Ethernet autoselect
                                  status: no carrier
                                  nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
                          ix1: flags=8863<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
                                  description: LAN (lan)
                                  options=4803828<VLAN_MTU,JUMBO_MTU,WOL_UCAST,WOL_MCAST,WOL_MAGIC,NOMAP>
                                  ether 34:12:78:56:01:03
                                  inet 192.168.1.1 netmask 0xffffff00 broadcast 192.168.1.255
                                  media: Ethernet autoselect
                                  status: no carrier
                                  nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
                          lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
                                  options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6>
                                  inet6 ::1 prefixlen 128
                                  inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
                                  inet 127.0.0.1 netmask 0xff000000
                                  groups: lo
                                  nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
                          enc0: flags=0<> metric 0 mtu 1536
                                  groups: enc
                                  nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
                          pflog0: flags=20100<PROMISC,PPROMISC> metric 0 mtu 33160
                                  groups: pflog
                          pfsync0: flags=0<> metric 0 mtu 1500
                                  syncpeer: 0.0.0.0 maxupd: 128 defer: off
                                  syncok: 1
                                  groups: pfsync
                          

                          Let me know if you need any other information.
                          Thank you

                          O 1 Reply Last reply Reply Quote 0
                          • O
                            ozon08 @shaker
                            last edited by

                            @shaker
                            Did you restart after adding the boot hints?

                            1 Reply Last reply Reply Quote 0
                            • S
                              shaker
                              last edited by

                              Yes I gestartet every time I made changes

                              1 Reply Last reply Reply Quote 0
                              • stephenw10S
                                stephenw10 Netgate Administrator
                                last edited by

                                OPNSense doesn't have the required drivers to access the switch. The same reason CE won't work. It can only work with pfSense Plus currently.

                                Steve

                                1 Reply Last reply Reply Quote 0
                                • S
                                  shaker
                                  last edited by

                                  What a pitty.
                                  I thought the base is Free BSD which give the possibility in general.
                                  Is there no way to bring the correct driver to FreeBSD and let it work?

                                  By the way, if somebody need access to the BIOS, just let me know.

                                  1 Reply Last reply Reply Quote 0
                                  • stephenw10S
                                    stephenw10 Netgate Administrator
                                    last edited by

                                    It only happens to work in pfSense Plus because we have done the development work for the 7100. There is basically zero incentive for Deciso to sponsor that in OPN so I'd say it's very unlikely.

                                    1 Reply Last reply Reply Quote 0
                                    • S
                                      shaker
                                      last edited by

                                      OK that's cool. Thank you.
                                      So one last question. When it works with plus only, do I need top buy it, or is there a way to get it for private use.
                                      I read there is a way to upgrade CE to plus, but therefore you need Internet access first on the device.
                                      So what's the best option?

                                      1 Reply Last reply Reply Quote 0
                                      • stephenw10S
                                        stephenw10 Netgate Administrator
                                        last edited by

                                        The easiest way is to install CE and upgrade to plus in something else then move the boot device across into the m270. Then re-register it there once you've added the switch scripts so it has connectivity.

                                        1 Reply Last reply Reply Quote 0
                                        • S
                                          shaker
                                          last edited by shaker

                                          Thank you very much for the support.
                                          I have now running pfsense plus on my M270.
                                          🤙

                                          1 Reply Last reply Reply Quote 1
                                          • stephenw10S
                                            stephenw10 Netgate Administrator
                                            last edited by

                                            Cool!
                                            Be aware that the driver code was never intended to run on that hardware so the startup scripts that ensure the 7100 works as expected will end up breaking it for the m270 at upgrade. At least currently.
                                            So if/when you do a firmware upgrade you will need access to the console to copy back the device hints and regain connectivity. I usually just have a backup of the file I can quickly copy back into place.

                                            Steve

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.