Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    pfSense on Watchguard M270

    Hardware
    18
    133
    32.4k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • stephenw10S
      stephenw10 Netgate Administrator
      last edited by

      You can see the internal ports 9 and 10 are disabled. You need to add to the script:

      etherswitchcfg port9 forwarding
etherswitchcfg port10 forwarding

      That is a change in the default behaviour of the switch since I first looked at it.

      Steve

      Z 2 Replies Last reply Reply Quote 0
      • Z
        zhellalex @stephenw10
        last edited by

        @stephenw10

        1 Reply Last reply Reply Quote 0
        • stephenw10S
          stephenw10 Netgate Administrator
          last edited by

          ??

          1 Reply Last reply Reply Quote 0
          • Z
            zhellalex @stephenw10
            last edited by

            @stephenw10 Thank you.
            Everything worked.

            1 Reply Last reply Reply Quote 1
            • S
              shaker
              last edited by

              I stephenw10,

              sorry for the late reply, I was on business.

              My etherswitchcfg shows this:

              [23.01-RELEASE][root@pfSense.home.arpa]/root: etherswitchcfg
etherswitch0: VLAN mode: DOT1Q
port1:
        pvid: 110
        state=1<DISABLED>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port2:
        pvid: 120
        state=1<DISABLED>
        flags=0<>
        media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active
port3:
        pvid: 130
        state=1<DISABLED>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port4:
        pvid: 140
        state=1<DISABLED>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port5:
        pvid: 150
        state=1<DISABLED>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port6:
        pvid: 160
        state=1<DISABLED>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port7:
        pvid: 170
        state=1<DISABLED>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port8:
        pvid: 180
        state=1<DISABLED>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port9:
        pvid: 1
        state=1<DISABLED>
        flags=1<CPUPORT>
        media: Ethernet 2500Base-KX <full-duplex>
        status: active
port10:
        pvid: 1
        state=1<DISABLED>
        flags=1<CPUPORT>
        media: Ethernet 2500Base-KX <full-duplex>
        status: active
vlangroup0:
        vlan: 1
        members 1,2,3,4,5,6,7,8,9,10
vlangroup1:
        vlan: 110
        members 1,9t
vlangroup2:
        vlan: 120
        members 2,10t
vlangroup3:
        vlan: 130
        members 3,10t
vlangroup4:
        vlan: 140
        members 4,10t
vlangroup5:
        vlan: 150
        members 5,10t
vlangroup6:
        vlan: 160
        members 6,10t
vlangroup7:
        vlan: 170
        members 7,10t
vlangroup8:
        vlan: 180
        members 8,10t

              What should I do next?

              stephenw10S 1 Reply Last reply Reply Quote 0
              • stephenw10S
                stephenw10 Netgate Administrator @shaker
                last edited by stephenw10

                All the ports are in state DISABLED so the script did not set them to FORWARDING correctly.

                Otherwise it looks good.

                1 Reply Last reply Reply Quote 0
                • S
                  shaker
                  last edited by

                  This is the script:

                  #!/bin/sh
#

echo "Configuring switch..."
logger Configuring switch...

etherswitchcfg config vlan_mode DOT1Q

etherswitchcfg vlangroup1 vlan 110 members 1,9t
etherswitchcfg vlangroup2 vlan 120 members 2,10t
etherswitchcfg vlangroup3 vlan 130 members 3,10t
etherswitchcfg vlangroup4 vlan 140 members 4,10t
etherswitchcfg vlangroup5 vlan 150 members 5,10t
etherswitchcfg vlangroup6 vlan 160 members 6,10t
etherswitchcfg vlangroup7 vlan 170 members 7,10t
etherswitchcfg vlangroup8 vlan 180 members 8,10t

etherswitchcfg port1 pvid 110
etherswitchcfg port2 pvid 120
etherswitchcfg port3 pvid 130
etherswitchcfg port4 pvid 140
etherswitchcfg port5 pvid 150
etherswitchcfg port6 pvid 160
etherswitchcfg port7 pvid 170
etherswitchcfg port8 pvid 180


echo "done"
logger done

                  Do I need some forwardings too?

                  R 1 Reply Last reply Reply Quote 0
                  • stephenw10S
                    stephenw10 Netgate Administrator
                    last edited by

                    Yes all the switch ports are disabled by default, you still need the section to set each port to forwarding. You might be able to combine that with the pvid. I've not tried that in one command.

                    1 Reply Last reply Reply Quote 0
                    • S
                      shaker
                      last edited by

                      Ok, now it looks like this:

                      etherswitch0: VLAN mode: DOT1Q
port1:
        pvid: 110
        state=8<FORWARDING>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port2:
        pvid: 120
        state=8<FORWARDING>
        flags=0<>
        media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active
port3:
        pvid: 130
        state=8<FORWARDING>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port4:
        pvid: 140
        state=8<FORWARDING>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port5:
        pvid: 150
        state=8<FORWARDING>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port6:
        pvid: 160
        state=8<FORWARDING>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port7:
        pvid: 170
        state=8<FORWARDING>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port8:
        pvid: 180
        state=8<FORWARDING>
        flags=0<>
        media: Ethernet autoselect (none)
        status: no carrier
port9:
        pvid: 1
        state=8<FORWARDING>
        flags=1<CPUPORT>
        media: Ethernet 2500Base-KX <full-duplex>
        status: active
port10:
        pvid: 1
        state=8<FORWARDING>
        flags=1<CPUPORT>
        media: Ethernet 2500Base-KX <full-duplex>
        status: active
vlangroup0:
        vlan: 1
        members 1,2,3,4,5,6,7,8,9,10
vlangroup1:
        vlan: 110
        members 1,9t
vlangroup2:
        vlan: 120
        members 2,10t
vlangroup3:
        vlan: 130
        members 3,10t
vlangroup4:
        vlan: 140
        members 4,10t
vlangroup5:
        vlan: 150
        members 5,10t
vlangroup6:
        vlan: 160
        members 6,10t
vlangroup7:
        vlan: 170
        members 7,10t
vlangroup8:
        vlan: 180
        members 8,10t

                      I am going ahead and give it a try!
                      Thank you from here!

                      1 Reply Last reply Reply Quote 0
                      • stephenw10S
                        stephenw10 Netgate Administrator
                        last edited by

                        Hmm, probably should remove VLAN1 from the switch. That's interesting, I guess that must be a default. You could probably just change the vlan groups you're defining to start at 0 so it gets replaced. However it won't affect anything since the PVID on the ports is set something other than 1.

                        Steve

                        1 Reply Last reply Reply Quote 0
                        • S
                          shaker
                          last edited by

                          It works fine for now. I didn't connect everything at the moment. But I am able to connect now, receiving IP and can organize the VLANs.
                          As next I need to configure pfsense. Will take some time. thanks guys

                          1 Reply Last reply Reply Quote 1
                          • V
                            verbatim419
                            last edited by

                            sorry to start the topic again.

                            I got an m270 and installed pfsense on it. I have inserted the hints for the switch but I can't insert the scripts, keeps throwing me an error No such file or directory when run comand chmod +x for sript
                            I new and sory for my english

                            1 Reply Last reply Reply Quote 0
                            • stephenw10S
                              stephenw10 Netgate Administrator
                              last edited by

                              You need to create those files.

                              How are you running those commands exactly?

                              V 1 Reply Last reply Reply Quote 0
                              • V
                                verbatim419 @stephenw10
                                last edited by verbatim419

                                @stephenw10 I downloaded one file from the system that has the extension "sh" and modified it with the script gave in previous posts, after which I transferred the file to the "/usr/local/etc/rc.d/" folder. After saving, I tried to start the shell both via the console and via the guia, but it threw out the above error. I writen script in notepad++. I'm a beginner when it comes to these things, so I apologize for some banalities.

                                1 Reply Last reply Reply Quote 0
                                • stephenw10S
                                  stephenw10 Netgate Administrator
                                  last edited by

                                  Ok I assume you mean the switch configuration script as shown here?: https://forum.netgate.com/post/990474

                                  You should create that file not add the code to a existing script.

                                  In my setup I run that script using a shellcmd not via rc.d.

                                  Steve

                                  R V 2 Replies Last reply Reply Quote 0
                                  • R
                                    reiter_f @stephenw10
                                    last edited by

                                    hi, i'm running the M270 too, it works when i switch the ports to forwarding "etherswitchcfg port# forwarding", but it loos the information after rebooting. after the reboot, the ports are disabled

                                    stephenw10S 1 Reply Last reply Reply Quote 0
                                    • P
                                      psp
                                      last edited by

                                      In my setup, I'm running the script @startup in Cron.

                                      1 Reply Last reply Reply Quote 0
                                      • stephenw10S
                                        stephenw10 Netgate Administrator @reiter_f
                                        last edited by

                                        @reiter_f said in pfSense on Watchguard M270:

                                        but it loos the information after rebooting. after the reboot, the ports are disabled

                                        Yes the switch is reset to defaults at boot. You have to reconfigure it at boot each time. It's easiest to do that using a script.

                                        R 1 Reply Last reply Reply Quote 0
                                        • R
                                          reiter_f @stephenw10
                                          last edited by reiter_f

                                          @stephenw10
                                          ha, there is no default config
                                          file that you are able to write in? i'm a little bit confused of this strategy,. because there is no ROM storage or something like that..... do you know where the config ist writen temporaly?
                                          how do i link the skript to the boot config, that it will run automatical at booting? ... the best would be to Clean all switch-configs before running the skript...

                                          1 Reply Last reply Reply Quote 0
                                          • stephenw10S
                                            stephenw10 Netgate Administrator
                                            last edited by

                                            When the switch is powered on it comes up with all the ports disabled by default. That's how the switch chip has been configured in hardware.

                                            There are several way to run a script. As discussed above I use a shellcmd to do it.

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.