Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    8x igb Intel(R) I211 / checksums - enable or disable / suricata

    Scheduled Pinned Locked Moved Hardware
    19 Posts 3 Posters 1.3k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • 4
      4o4rh @stephenw10
      last edited by

      @stephenw10 what I don't understand is; why am i having different options on the igb interfaces if the settings are global?

      I have h/w checksums enabled, TSO disabled, LRO disabled and net.inet.tcp.tso = 0

      looking at the below options 2,4,5,6,7 have the correct settings but 0,1,3 do not.

      ifconfig igb0
options=4e523bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,NOMAP> 

ifconfig igb1 
options=4e120bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6,NOMAP>

ifconfig igb2
options=48120b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_MAGIC,VLAN_HWFILTER,NOMAP>

ifconfig igb3
options=4e120bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6,NOMAP>

ifconfig igb4
options=48120b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_MAGIC,VLAN_HWFILTER,NOMAP>

ifconfig igb5
options=48120b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_MAGIC,VLAN_HWFILTER,NOMAP>

ifconfig igb6
options=48120b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_MAGIC,VLAN_HWFILTER,NOMAP>

ifconfig igb7 
options=48120b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_MAGIC,VLAN_HWFILTER,NOMAP>
      1 Reply Last reply Reply Quote 0
      • stephenw10S
        stephenw10 Netgate Administrator
        last edited by

        pfSense applies settings to the NICs when it sets them up at boot with ifconfig. If they are not assigned they never get settings applied to them.
        If you have set global driver variables via loader values those will be applied to all NICs using that driver.
        If you have set sysctls for the driver those will be applied to the specific NIC they are set for.

        Steve

        4 2 Replies Last reply Reply Quote 0
        • 4
          4o4rh @stephenw10
          last edited by

          @stephenw10 I mean my config is;

          Advanced Networking
          Hardware Checksum Offloading - unchecked
          Disable hardware TCP segmentation offload - checked
          Disable hardware large receive offload - checked

          System Tunables
          Enable TCP Segmentation Offload (1) - 0

          Loader Config Local
          net.inet.tcp.tso=0

          igb0 - pppoe ** why tso6/tso4 + rxcsum/txcsum
          igb1 - cable modem ** why rxcsum/txcsum + ipv6
          igb2 - not connected
          igb3 - 100M end point ** why rxcsum/txcsum + ipv6
          igb4 - lagg0
          igb5 - lagg0
          igb6 - uplink switch
          igb7 - not connected

          1 Reply Last reply Reply Quote 0
          • 4
            4o4rh @stephenw10
            last edited by 4o4rh

            @stephenw10 so i added the below to config.xml;

            <shellcmd>ifconfig igb0 -txcsum -rxcsum -tso4 -tso6 -lro -txcsum6 -rxcsum6 -vlanhwtso</shellcmd>
<shellcmd>ifconfig igb1 -txcsum -rxcsum -tso4 -tso6 -lro -txcsum6 -rxcsum6 -vlanhwtso</shellcmd>
<shellcmd>ifconfig igb3 -txcsum -rxcsum -tso4 -tso6 -lro -txcsum6 -rxcsum6 -vlanhwtso</shellcmd>

            I got the below after boot, noting that igb1 is still showing the txc/rscsums.
            If i run the command again for igb1 manually, it seems to work.

            needs to be run with a delay or a test if the interface is up maybe?
            ** I tell a lie. It takes it momentarily, but then reverts back to the full settings

            ifconfig igb7
options=48120b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_MAGIC,VLAN_HWFILTER,NOMAP>

ifconfig igb6
options=48120b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_MAGIC,VLAN_HWFILTER,NOMAP>

ifconfig igb5
options=48120b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_MAGIC,VLAN_HWFILTER,NOMAP>

ifconfig igb4
options=48120b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_MAGIC,VLAN_HWFILTER,NOMAP>

ifconfig igb3
options=48120b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_MAGIC,VLAN_HWFILTER,NOMAP>

ifconfig igb2
options=48120b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_MAGIC,VLAN_HWFILTER,NOMAP>

ifconfig igb1
options=4e120bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_MAGIC,VLAN_HWFILTER,RXCSUM_IPV6,TXCSUM_IPV6,NOMAP>

ifconfig igb0
options=48120b8<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_MAGIC,VLAN_HWFILTER,NOMAP>
            1 Reply Last reply Reply Quote 0
            • stephenw10S
              stephenw10 Netgate Administrator
              last edited by

              By unchecking the box in Sys > Adv > Networking you are enabling checksum offloading globally. So whenever an interface is configured it will be set as enabled. Probably igb1 linked/unlinked after that shellcmd ran so it was enabled again.

              4 1 Reply Last reply Reply Quote 0
              • 4
                4o4rh @stephenw10
                last edited by 4o4rh

                @stephenw10 so actually, the command should be then;
                <shellcmd>ifconfig igb0 -tso4 -tso6 -lro -vlanhwtso</shellcmd>
                as it is only tso and lro that we need to turn off right

                but in any case, the system is doing it's own thing.

                If i enter the below, some turn rxc/txc on and some off, but if i run the command from the shell it works.

                <shellcmd>ifconfig igb0 rxcsum txcsum -tso4 -tso6 -lro rxcsum6 txcsum6 -vlanhwtso</shellcmd>
<shellcmd>ifconfig igb1 rxcsum txcsum -tso4 -tso6 -lro rxcsum6 txcsum6 -vlanhwtso</shellcmd>
<shellcmd>ifconfig igb2 rxcsum txcsum -tso4 -tso6 -lro rxcsum6 txcsum6 -vlanhwtso</shellcmd>
<shellcmd>ifconfig igb3 rxcsum txcsum -tso4 -tso6 -lro rxcsum6 txcsum6 -vlanhwtso</shellcmd>
<shellcmd>ifconfig igb4 rxcsum txcsum -tso4 -tso6 -lro rxcsum6 txcsum6 -vlanhwtso</shellcmd>
<shellcmd>ifconfig igb5 rxcsum txcsum -tso4 -tso6 -lro rxcsum6 txcsum6 -vlanhwtso</shellcmd>
<shellcmd>ifconfig igb6 rxcsum txcsum -tso4 -tso6 -lro rxcsum6 txcsum6 -vlanhwtso</shellcmd>
<shellcmd>ifconfig igb7 rxcsum txcsum -tso4 -tso6 -lro rxcsum6 txcsum6 -vlanhwtso</shellcmd>
                1 Reply Last reply Reply Quote 0
                • stephenw10S
                  stephenw10 Netgate Administrator
                  last edited by

                  Since you don't have igb0 assigned dircetly it doesn't make any difference there. The ppp traffic using it cannot be off-loaded. Part of the reason PPPoE is always slower.

                  You can use the afterfilterchnageshellcmd type to apply settings when an interface is relinked if you need to.
                  You probably don't need to do any of that though.

                  4 1 Reply Last reply Reply Quote 0
                  • 4
                    4o4rh @stephenw10
                    last edited by

                    @stephenw10 i thought you meant

                    <system>
                    <afterfilterchangeshellcmd></afterfilterchangeshellcmd>
                    </system>

                    took down my system ;-)

                    I can't find any document on setting that value

                    1 Reply Last reply Reply Quote 0
                    • stephenw10S
                      stephenw10 Netgate Administrator
                      last edited by

                      It will run the command everytime the filter is reloaded.

                      It may have created a loop if running that command triggers the filter to reload.

                      4 1 Reply Last reply Reply Quote 0
                      • 4
                        4o4rh @stephenw10
                        last edited by

                        @stephenw10 i mean i edited the config.xml which crashed the machine. I didn't realize there was a shellcmd package to install

                        1 Reply Last reply Reply Quote 0
                        • stephenw10S
                          stephenw10 Netgate Administrator
                          last edited by

                          Ah, yes, much safer to use the package!

                          4 2 Replies Last reply Reply Quote 0
                          • 4
                            4o4rh @stephenw10
                            last edited by 4o4rh

                            @stephenw10 except it only allows one afterfiltercmd.

                            p.s. very weird. after adding the command for igb0 in the afterfilter all igb interfaces now have the desired settings

                            1 Reply Last reply Reply Quote 0
                            • 4
                              4o4rh @stephenw10
                              last edited by

                              @stephenw10 i thought this was fixed, but it seems the suricata package was not updated properly.
                              once i reinstalled the suricata package, the problem of different settings per igb is back.

                              using the aftersfilterchangeshellcmd does work, for the specific interface but you can only do one.

                              1 Reply Last reply Reply Quote 0
                              • stephenw10S
                                stephenw10 Netgate Administrator
                                last edited by

                                Use a script in the shellcmd that runs on whatever interfaces you need.

                                1 Reply Last reply Reply Quote 0
                                • First post
                                  Last post
                                Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.