Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    Watchguard M5600

    Scheduled Pinned Locked Moved Hardware
    15 Posts 3 Posters 1.4k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • R
      reiter_f @stephenw10
      last edited by

      @stephenw10
      hi, i setup all ports with statik IP and DHCP-server... and tested the funktion. the port numbers are mixed around ... 3 ports works, one without DHCP Funktion, 2 after 1minute at 100Mbit and 3 are totaly without Funktion... cfconfig ans sysctl looks i think normal

      1 Reply Last reply Reply Quote 0
      • stephenw10S
        stephenw10 Netgate Administrator
        last edited by

        Hmm, well that sounds odd. Do you know the ports all worked normally under the Watchguard OS?

        R 1 Reply Last reply Reply Quote 0
        • R
          reiter_f @stephenw10
          last edited by

          @stephenw10

          no, sorry, i got the box without CFast card.
          is there a possebility to reinstall the igb driver, because i have don ethe installation on the HyperV

          1 Reply Last reply Reply Quote 0
          • stephenw10S
            stephenw10 Netgate Administrator
            last edited by

            I'd be very surprised if it's a driver problem. If it works on two of those NICs it should work identically on all of them.

            R 1 Reply Last reply Reply Quote 0
            • R
              reiter_f @stephenw10
              last edited by

              @stephenw10
              i only was thinking about an driver problem because the Prots are totaly mixed ...port 1 is igb0, port 3 is igb1, port 4 is igb6, port 7 is igb3 ....

              1 Reply Last reply Reply Quote 0
              • stephenw10S
                stephenw10 Netgate Administrator
                last edited by

                That's not a driver problem. The NICs are assigned in the order they are discovered on the PCIe bus. It's possible to force the order using PCI device wiring but I would not recommend it since reinstalling defaults the config and mixes up everything again! Better to just assign the interfaces in the expected order after install so the ordering is held in the config.

                1 Reply Last reply Reply Quote 0
                • stephenw10S
                  stephenw10 Netgate Administrator
                  last edited by

                  Do you have the default NIC modules in that? An 8 port 1G copper module and a 4 port 10G fiber module?

                  R 1 Reply Last reply Reply Quote 0
                  • R
                    reiter_f @stephenw10
                    last edited by

                    @stephenw10
                    yes, i have the default modules ... i have alsow cahnged the position of it.
                    i reinstalled the whole pfsense 2.7 and upgraded it to pfsense+ ... but with the same result ... maybe the card is death :)

                    1 Reply Last reply Reply Quote 0
                    • stephenw10S
                      stephenw10 Netgate Administrator
                      last edited by

                      Hmm, maybe. Though the ports usually fail completely if they see some sort of electrical surge etc. Do you see link LEDs on all ports?

                      R 1 Reply Last reply Reply Quote 0
                      • R
                        reiter_f @stephenw10
                        last edited by

                        @stephenw10
                        no, some of these ports are generaly not active ... no LED

                        1 Reply Last reply Reply Quote 0
                        • First post
                          Last post
                        Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.