Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    Interfaces assignment?

    Scheduled Pinned Locked Moved General pfSense Questions
    15 Posts 3 Posters 1.4k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • stephenw10S
      stephenw10 Netgate Administrator
      last edited by

      If you change router device, and hence the MAC, the modem would likely have to be rebooted. But otherwise you should be able to disconnect the WAN cable or reboot pfSense and it will pull an IP again. Is that not the case?

      W 1 Reply Last reply Reply Quote 0
      • W
        Waqar.UK @stephenw10
        last edited by

        @stephenw10

        I far as I know what I have seen on my search on the Internet, for VM is what I said to obtain a WAN IP the cable modem has to re-booted after leaving it off for about 2 minutes.
        He cannot get to the Web GUI.

        1 Reply Last reply Reply Quote 0
        • stephenw10S
          stephenw10 Netgate Administrator
          last edited by

          Like every time they reboot pfSense? That seems ridiculous. Can we see a boot log DHCP log?

          But that didn't happen in 2.6?

          W 1 Reply Last reply Reply Quote 0
          • W
            Waqar.UK @stephenw10
            last edited by

            @stephenw10 said in Interfaces assignment?:

            Like every time they reboot pfSense? That seems ridiculous. Can we see a boot log DHCP log?

            But that didn't happen in 2.6?

            He has decided to re install 2.7. No it it did not take place with 2.6.
            Nothing has changed apart from a new Asus wireless. But that should not stop Pfsense from getting a WAN or LAN.

            1 Reply Last reply Reply Quote 0
            • stephenw10S
              stephenw10 Netgate Administrator
              last edited by

              I agree. If it still does so after after reinstalling 2.7 clean I'd say it's almost certainly because of the timing change at boot.
              If you look through the system logs and see the WAN interface show link UP during boot and ignoring it that's probably the problem.

              W 1 Reply Last reply Reply Quote 0
              • W
                Waqar.UK @stephenw10
                last edited by

                @stephenw10

                At boot, part of the sequence shows that the WAN is OK.
                Is that part of what I should look out for?
                How can I see system logs?

                1 Reply Last reply Reply Quote 0
                • stephenw10S
                  stephenw10 Netgate Administrator
                  last edited by

                  You can see the logs in the gui in Status > System Logs. The main System tab there will show it if it's just booted.

                  If you see log entries showing the WAN link going UP and DOWN during boot and possibly /rc.linkup: Ignoring link event during boot sequence.

                  Then you might be hitting this. Adding a boot delay may prevent it. See for example: https://forum.netgate.com/topic/181890/pfsense-router-does-not-receive-ip-adress-from-isp

                  W 1 Reply Last reply Reply Quote 0
                  • W
                    Waqar.UK @stephenw10
                    last edited by Waqar.UK

                    @stephenw10

                    I will ask him, but he has made up his mind to do a fresh install of version 2.7.

                    1 Reply Last reply Reply Quote 0
                    • stephenw10S
                      stephenw10 Netgate Administrator
                      last edited by

                      Reinstalling is always a good test. That will show if it;s something in the config or something brought across in an upgrade.

                      W 1 Reply Last reply Reply Quote 1
                      • W
                        Waqar.UK @stephenw10
                        last edited by Waqar.UK

                        @stephenw10

                        I helped him to do a clean new install of ver 2.7.
                        All is working now.

                        1 Reply Last reply Reply Quote 2
                        • First post
                          Last post
                        Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.