W10 / Ikev2 + radius on PFSENSE

aniodon

thanks,

they were indeed different. I corrected the CA and certificate in radius and restarted IPSEC.

i still get (1) Login incorrect (Failed retrieving values required to evaluate condition) , when i am not in a "No password encryption/no google" setup.

Konstanti

@aniodon

You need to stop the Freeradius service
/Status/services/
From the PF console run freeradius in debug mode
radiusd -X

Then you try to establish a connection and analyze the errors

aniodon

@Konstanti :

Sorry for the delay, took me a while to connect, get logs and sanitize

(0) Received Access-Request Id 63 from XXX:4608 to XXX:1812 length 167
(0)   User-Name = "XXX"
(0)   NAS-Port-Type = Virtual
(0)   Service-Type = Framed-User
(0)   NAS-Port = 20
(0)   NAS-Port-Id = "con-mobile"
(0)   NAS-IP-Address = XXX
(0)   Called-Station-Id = "XXX[4500]"
(0)   Calling-Station-Id = "XXX[4500]"
(0)   EAP-Message = 0x02000013016f6c69766965722e7065726e6573
(0)   NAS-Identifier = "strongSwan"
(0)   Message-Authenticator = 0xf18266cb0a8226f4f224c8f18eb6cb9e
(0) # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default
(0)   authorize {
(0)     [preprocess] = ok
(0)     [chap] = noop
(0)     [mschap] = noop
(0)     [digest] = noop
(0) suffix: Checking for suffix after "@"
(0) suffix: No '@' in User-Name = "XXX", skipping NULL due to config.
(0)     [suffix] = noop
(0) ntdomain: Checking for prefix before "\"
(0) ntdomain: No '\' in User-Name = "XXX", skipping NULL due to config.
(0)     [ntdomain] = noop
(0) eap: Peer sent EAP Response (code 2) ID 0 length 19
(0) eap: EAP-Identity reply, returning 'ok' so we can short-circuit the rest of authorize
(0)     [eap] = ok
(0)   } # authorize = ok
(0) Found Auth-Type = eap
(0) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(0)   authenticate {
(0) eap: Peer sent packet with method EAP Identity (1)
(0) eap: Calling submodule eap_mschapv2 to process data
(0) eap_mschapv2: Issuing Challenge
(0) eap: Sending EAP Request (code 1) ID 1 length 43
(0) eap: EAP session adding &reply:State = 0xdfebf9ccdfeae3f1
(0)     [eap] = handled
(0)   } # authenticate = handled
(0) Using Post-Auth-Type Challenge
(0) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(0)   Challenge { ... } # empty sub-section is ignored
(0) Sent Access-Challenge Id 63 from XXX:1812 to XXXX:4608 length 0
(0)   EAP-Message = 0x0101002b1a0101002610f38b08acd1311eefcb492fa37fff3cd8667265657261646975732d332e302e3137
(0)   Message-Authenticator = 0x00000000000000000000000000000000
(0)   State = 0xdfebf9ccdfeae3f19eb8b5707e5d7a79
(0) Finished request
Waking up in 4.9 seconds.
(1) Received Access-Request Id 64 from XXX:4608 to XXX:1812 length 239
(1)   User-Name = "XXX"
(1)   NAS-Port-Type = Virtual
(1)   Service-Type = Framed-User
(1)   NAS-Port = 20
(1)   NAS-Port-Id = "con-mobile"
(1)   NAS-IP-Address = XXX
(1)   Called-Station-Id = "XXX4500]"
(1)   Calling-Station-Id = "XXX[4500]"
(1)   EAP-Message = 0x020100491a02010044318d9f92f4ffafcd3cfea6f97ccd098ddc000000000000000008b552fb470b098eea40b7be084f902e5d471f37d0a1dcc0006f6c69766965722e7065726e6573
(1)   NAS-Identifier = "strongSwan"
(1)   State = 0xdfebf9ccdfeae3f19eb8b5707e5d7a79
(1)   Message-Authenticator = 0x5e084f4a691fe612767c92001f1015e8
(1) session-state: No cached attributes
(1) # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default
(1)   authorize {
(1)     [preprocess] = ok
(1)     [chap] = noop
(1)     [mschap] = noop
(1)     [digest] = noop
(1) suffix: Checking for suffix after "@"
(1) suffix: No '@' in User-Name = "XXX", skipping NULL due to config.
(1)     [suffix] = noop
(1) ntdomain: Checking for prefix before "\"
(1) ntdomain: No '\' in User-Name = "XXX", skipping NULL due to config.
(1)     [ntdomain] = noop
(1) eap: Peer sent EAP Response (code 2) ID 1 length 73
(1) eap: No EAP Start, assuming it's an on-going EAP conversation
(1)     [eap] = updated
(1) files: users: Matched entry XXX at line 2
(1)     [files] = ok
rlm_counter: Entering module authorize code
rlm_counter: Could not find Check item value pair
(1)     [daily] = noop
rlm_counter: Entering module authorize code
rlm_counter: Could not find Check item value pair
(1)     [weekly] = noop
rlm_counter: Entering module authorize code
rlm_counter: Could not find Check item value pair
(1)     [monthly] = noop
rlm_counter: Entering module authorize code
rlm_counter: Could not find Check item value pair
(1)     [forever] = noop
(1)     if (&request:Calling-Station-Id == &control:Calling-Station-Id) {
(1)     ERROR: Failed retrieving values required to evaluate condition
(1)     [expiration] = noop
(1)     [logintime] = noop
(1) pap: WARNING: No "known good" password found for the user.  Not setting Auth-Type
(1) pap: WARNING: Authentication will fail unless a "known good" password is available
(1)     [pap] = noop
(1)   } # authorize = updated
(1) Found Auth-Type = eap
(1) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(1)   authenticate {
(1) eap: Expiring EAP session with state 0xdfebf9ccdfeae3f1
(1) eap: Finished EAP session with state 0xdfebf9ccdfeae3f1
(1) eap: Previous EAP request found for state 0xdfebf9ccdfeae3f1, released from the list
(1) eap: Peer sent packet with method EAP MSCHAPv2 (26)
(1) eap: Calling submodule eap_mschapv2 to process data
(1) eap_mschapv2: # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(1) eap_mschapv2:   authenticate {
(1) mschap: WARNING: No Cleartext-Password configured.  Cannot create NT-Password
(1) mschap: WARNING: No Cleartext-Password configured.  Cannot create LM-Password
(1) mschap: Creating challenge hash with username: XXX
(1) mschap: Client is using MS-CHAPv2
(1) mschap: ERROR: FAILED: No NT/LM-Password.  Cannot perform authentication
(1) mschap: ERROR: MS-CHAP2-Response is incorrect
(1)     [mschap] = reject
(1)   } # authenticate = reject
(1) eap: Sending EAP Failure (code 4) ID 1 length 4
(1) eap: Freeing handler
(1)     [eap] = reject
(1)   } # authenticate = reject
(1) Failed to authenticate the user
(1) Using Post-Auth-Type Reject
(1) # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(1)   Post-Auth-Type REJECT {
(1) attr_filter.access_reject: EXPAND %{User-Name}
(1) attr_filter.access_reject:    --> XXX
(1) attr_filter.access_reject: Matched entry DEFAULT at line 11
(1)     [attr_filter.access_reject] = updated
(1)     [eap] = noop
(1)     policy remove_reply_message_if_eap {
(1)       if (&reply:EAP-Message && &reply:Reply-Message) {
(1)       if (&reply:EAP-Message && &reply:Reply-Message)  -> FALSE
(1)       else {
(1)         [noop] = noop
(1)       } # else = noop
(1)     } # policy remove_reply_message_if_eap = noop
(1)   } # Post-Auth-Type REJECT = updated
(1) EXPAND %{User-Name} - %{reply:Acct-Output-Octets}
(1)    --> XXX -
(1) Login incorrect (Failed retrieving values required to evaluate condition): [XXX/<via Auth-Type = eap>] (from client Frigo port 20 cli XXX[4500]) XXX -
(1) Delaying response for 1.000000 seconds
Waking up in 0.3 seconds.
Waking up in 0.6 seconds.
(1) Sending delayed response
(1) Sent Access-Reject Id 64 from XXX:1812 to XXX:4608 length 127
(1)   MS-CHAP-Error = "\001E=691 R=1 C=bf32f65eb19092390d7f03336fad171a V=3 M=Authentication rejected"
(1)   EAP-Message = 0x04010004
(1)   Message-Authenticator = 0x00000000000000000000000000000000
Waking up in 3.9 seconds.
(0) Cleaning up request packet ID 63 with timestamp +35
(1) Cleaning up request packet ID 64 with timestamp +35
Ready to process requests

Konstanti

@aniodon

(1) eap_mschapv2: # Executing group from file /usr/local/etc/raddb/sites-enabled/default
(1) eap_mschapv2:   authenticate {
(1) mschap: WARNING: No Cleartext-Password configured.  Cannot create NT-Password
(1) mschap: WARNING: No Cleartext-Password configured.  Cannot create LM-Password
(1) mschap: Creating challenge hash with username: XXX
(1) mschap: Client is using MS-CHAPv2
(1) mschap: ERROR: FAILED: No NT/LM-Password.  Cannot perform authentication
(1) mschap: ERROR: MS-CHAP2-Response is incorrect
(1)     [mschap] = reject
(1)   } # authenticate = reject

aniodon

Thank you @Konstanti, but, you cannot set password when in google mode :

Konstanti

@aniodon

Miscellaneous configuration and hints:

The configuration for different mobile devices can be found here.

And here is the software for mobile devices.

Please read the limitations to make sure how secure this is.

mOTP will probably not work with EAP, CHAP, MSCHAP. If it does - tell me how :-)

aniodon

@Konstanti : The quote is from the mOTP section. Are mOTP and the One-time-Password from users pannel the same ?
mOTP is disabled in my conf

Do you know if i have an alternative ?
i would not like to use credentials in clear text and i would like to use more elaborate ways of authenticate

thank you

nippertje

Hi @aniodon

Did you ever get this working? I am trying to achieve something similar and have run into the same problem.

aniodon

@nippertje hello, sorry but no. I concluded this was not possible and Just gave up.

jimp

You can't use that kind of OTP with EAP because using mOTP/GA requires PAP which is unencrypted, while EAP will refuse to work with anything less than complete end-to-end encryption of the credentials.

You would need some other sort of MFA hooked into radius, likely from an external/third party radius server.

nippertje

Thanks @jimp - I found that out with additional reading, so changed tack and now am using OpenVPN with ESET Secure Authentication, which works well and provides convenient push authentication.