Squid port 3128 and Firewall Rules

[JonathanLee]

this was also tested

[mcury]

@JonathanLee If that is not a TCP:S, it should be an out of state connection.
Could be asymmetric route but I don't think that is the case.

All you need is to allow clients to connect to their gateway IP address (pfsense), on port 3128.

Port 3128 will handle SSL connections too. I don't remember ever having to use port 3129.

[JonathanLee]

@mcury I wonder why it keeps doing it, it does it for every single lan device in the logs all day. But everything is working on the user end.

[JonathanLee]

@mcury I even have any flag set for all the rules tested

[JonathanLee]

@mcury Maybe they are my URL blocks that still try to connect?

[mcury]

@JonathanLee Leave only one rule, clients to default gateway, TCP port 3128.
Leave this rule with default settings.

Try this:

There, where you see Firewall Optimization Options, change to conservative.

Note that this option will increase memory usage of the firewall.

[mcury]

@JonathanLee said in Squid port 3128 and Firewall Rules:

Maybe they are my URL blocks that still try to connect?

I can't see how could be that.

[JonathanLee]

@mcury Done set it back to how I had it.

Rules normalized

Changed to conservative optimization

[mcury]

@JonathanLee said in Squid port 3128 and Firewall Rules:

Changed to conservative optimization

I think that will do it..

[JonathanLee]

Dang still blocks

[JonathanLee]

@mcury any other ideas?

[mcury]

@JonathanLee Its blocking out connections, from pfsense to the host, with a default deny ipv4 rule?

Check with cat /tmp/rules.debug in the shell, search for that rule.

Do you have any floating rules ?

[JonathanLee]

@mcury Yes I have floating rules for traffic shaping

[JonathanLee]

@mcury said in Squid port 3128 and Firewall Rules:

cat /tmp/rules.debug

Rule

[mcury]

@JonathanLee

# default deny rules
#---------------------------------------------------------------------------
block in log inet all ridentifier 1000000103 label "Default deny rule IPv4"
block out log inet all ridentifier 1000000104 label "Default deny rule IPv4"

I suppose you have transparent proxy also enabled ? For systems that can't set a proxy by hand ?
If that is the case, disable transparent proxy for one second to see if it is not related to the rdr pass you have up there

[JonathanLee]

@mcury Yes I do have both, my XBOX uses the transparent side

[mcury]

@JonathanLee said in Squid port 3128 and Firewall Rules:

@mcury Yes I do have both, my XBOX uses the transparent side

Have you bypassed all other hosts that don't need transparent proxy in the Squid settings ?

Disable transparent proxy for one sec and test.

If it works, enable it again and try to bypass clients that are pointing to the proxy (explicit) in the transparent settings.

[JonathanLee]

@mcury How do you bypass for example one host like 192.168.1.17 from the SSL intercept but still make it use the the transparent proxy?

[mcury]

@JonathanLee said in Squid port 3128 and Firewall Rules:

How do you bypass for example one host like 192.168.1.17 from the SSL intercept but still make it use the the transparent proxy?

1- Disable transparent proxy
2- You would have to create the transparent NAT manually, using a ! in the source, with that IP address.
3- That NAT would have to redirect outbound TCP 443 connections to 127.0.0.1 3128.

Test like that, if doesn't work, try to change the port in the 3rd step to 3129.

I think that will do it.

Note that you would also need to create one for port 80.

[JonathanLee]

@mcury Thanks!!!! that helps a lot I no longer see double requests for everything and it all still works!!! The XBOX uses transparent and UpNp and all the devices that know about the proxy don't need the transparent!!! YES!!!