miniUPnPd not working since 23.09 (worked in 23.05.1)
-
Because that's the port minipnpd listens on the http:
curl http://192.168.200.1:2189/rootDesc.xmlAs far as I know that can be omitted entirely and miniupnpd will use a random port.
Setting it to 1900 is probably a bad idea since it should already be listening there. Though for udp.
-
@stephenw10 were they come up with that port, I don't show it registered as that.. Pretty sure radware has that registered for something they do radware-rpm-s
And I concur - setting that port in the config to 1900 prob not a good idea, and I would think really had nothing to do with his issue.. UPnP is UDP.
-
Yeah, unclear. Looks like they removed that over on the other side after deciding it was pointless setting it.
-
@stephenw10
I disable port in the conf file and now miniupnpd use a random port.
It's still working
How can I know if the port 2189 is already use by another service ? -
@PiAxel said in miniUPnPd not working since 23.09 (worked in 23.05.1):
How can I know if the port 2189 is already use by another service ?
do the command I did with sockstat
-
@johnpoz
ok thank you
but it is not used... -
@PiAxel well if its running and you want to know what port it is using do
sockstat | grep miniupnpd
-
/root: sockstat | grep miniupnpd root miniupnpd 36049 4 tcp6 *:51760 *:* root miniupnpd 36049 5 dgram -> /var/run/log root miniupnpd 36049 6 tcp4 *:51760 *:* root miniupnpd 36049 7 udp4 *:1900 *:* root miniupnpd 36049 8 stream /var/run/php-fpm.socket root miniupnpd 36049 9 udp6 *:1900 *:* root miniupnpd 36049 10 udp4 192.168.1.1:55617 *:* root miniupnpd 36049 11 udp6 *:64174 *:* root miniupnpd 36049 12 stream /var/run/php-fpm.socket root miniupnpd 36049 14 udp4 192.168.1.1:5351 *:* root miniupnpd 36049 15 udp6 *:5351 *:* -
That seems fine. I have no explanation as to why changing the port value to 1900 seemed to allow it work though. That really shouldn't have changed anything significant.
-
thank you very much for your help !
-
@PiAxel
The problem is back since update 23.09.1
everything seems to be working fine but neither my NAS nor any other network device can open a port via upnp. the games on my pc say that I am in strict NAT.
In pfsense stat upnp is empty.
I try with port=0 instead of 2189 but it didn't change anything
Tell me what you want to know about my pfsense.Please help me!
-
I have disabled STUN and there is no more message with "port forwarding is now disabled" but that still doesn't work.
-
@PiAxel said in miniUPnPd not working since 23.09 (worked in 23.05.1):
STUN: ext interface ix0 has now public IP address external ipv4 but firewall filters incoming connections set by miniunnpd
That implies you have something set that is preventing miniupnpd opening inbound ports somehow.
Do you have a custom block all rule on WAN or as Floating?
-
@stephenw10
No, I don't have any rule on WAN or as floating to block all -
Could be something upstream blocking it then. Try to send some traffic to your WAN from some external address and see if it arrives in a packet capture.
-
you have to add a rule in wan to allow...
## External Network ext_ifname=igc0 ext_perform_stun=yes ext_stun_host=198.100.144.121 ext_stun_port=3478 ## Internal Network listening_ip=bridge0 ipv6_disable=yes allow 1024-65535 192.168.1.0/24 1024-65535 deny 0-65535 0.0.0.0/0 0-65535 bitrate_down=512000 bitrate_up=1024000 ## UPnP Settings anchor=miniupnpd enable_natpmp=yes enable_upnp=yes secure_mode=yes min_lifetime=120 max_lifetime=86400 system_uptime=yes notify_interval=60 clean_ruleset_interval=600 packet_log=yes uuid=fb241e30-9c00-11ee-xxxxxxxxxxx serial=CA0A9DD5
