not reboot sg3100
-
hi i lost connection to my sg 3100 last night
it flashes in the circle symbol and does not get further into the start process
I have tried to put a usb cable in the console port and use putty but I can't write commands there, it doesn't respond to the keyboard
I have also tried with a paper clip in the hole for 3 seconds, the same thing happens, the symbol flashes in a circle
What options do I have to get it up and running again? -
Go for a power cycle and have a look at the console.
-
Has the console ever worked?
Try a different USB cable. Try a different terminal client device if you can.
Steve
-
now it is possible to connect securecrt via usb cable, can I make a bacob from the marvell prompt and can I run some reprations mode
i cant get it to run fsck
when it starts upGeneral initialization - Version: 1.0.0
AVS selection from EFUSE disabled (Skip reading EFUSE values)
Overriding default AVS value to: 0x23
Detected Device ID 6820
High speed PHY - Version: 2.0Init Customer board board SerDes lanes topology details:
| Lane # | Speed| Type |
------------------------------|
| 0 | 3 | SATA0 |
| 1 | 5 | PCIe0 |
| 2 | 3 | SATA1 |
| 3 | 4| SGMII2 |
| 4| 5 | PCIe1 |
| 5 | 5 | USB3 HOST1 |PCIe Ref. Clock Buffer Control is 0xf00015bf, setting to 0xf00015bf
SOC_CONTROL_REG1 is 0xf00015bf, setting to 0x0707c0f3
PCIe, Idx 0: detected no link
PCIe, Idx 1: detected no link
High speed PHY - Ended Successfully
mv_ddr: mv_ddr-armada-17.06.1-g07f8294 (Oct 8 2018 - 12:59:22)
DDR4 Training Sequence - Switching XBAR Window to FastPath Window
mv_ddr: completed successfully
| / | __ _ _ ____ | | |
| |/| |/ _` | '\ \ / / _ \ | |
| | | | (| | | \ V / __/ | |
|| ||_,|| _/ _|||
_ _ ____ _
| | | | | __ ) ___ ___ | |
| | | || _ \ / _ \ / _ | __|
| || || |) | () | () | |_
_/ |____/ _/ ___/ __|
** LOADER **U-Boot 2013.01-02879-geb5cbf6642 (Oct 08 2018 - 12:59:19) Marvell version: devel-17.06.0
Board: Rogue-1
SoC: MV88F6820 Rev B0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1600 [MHz]
L2 @ 800 [MHz]
TClock @ 250 [MHz]
DDR4 @ 800 [MHz]
DDR4 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 2 GiB
MMC: mv_sdh: 0
DBG: Calling spi_flash_probe from env_relocate_spec()
SF: Probing bus 0 cs 0 @ 20000000Hz mode 3
SF: Detected W25Q32JV with page size 4 KiB, total 4 MiB
PCI-e 0: Detected No Link.
PCI-e 1: Detected No Link.
USB2.0 0: Host Mode
USB3.0 1: Host ModeMap: Code: 0x7fedc000:0x7ff9741c
BSS: 0x7ffef600
Stack: 0x7f4cbf20
Heap: 0x7f4cc000:0x7fedc000
U-Boot Environment: 0x00100000:0x00110000 (SPI)Board configuration detected:
Net:port Interface PHY address egiga0 RGMII 0x00 egiga1 RGMII 0x01 egiga2 SGMII In-Band egiga0 [PRIME], egiga1, egiga2 Hit any key to stop autoboot: 0 reading ubldr.bin ** Unable to read file ubldr.bin ** Starting application at 0x00200000 ...
then it won't go on
what can I do
-
You can reinstall from the Marvell prompt:
https://docs.netgate.com/pfsense/en/latest/solutions/sg-3100/reinstall-pfsense.htmlOpen a ticket with us to get the recovery image:
https://www.netgate.com/tac-support-request
