Problem booting netgate 2100
-
Hello team, today I encountered an error where my Netgate 2100 was not loading and was stuck at a blinking blue light on the circle LED.
Since am not tech-savvy I just connected to the console port and rebooted the device and the following boot log appeared with an error. any help would be highly appreciated thanks.OK reboot
resetting ...
TIM-1.0
WTMI-devel-1.0.0-1115f12
WTMI: system early-init
SVC REV: 5, CPU VDD voltage: 1.237V
NOTICE: Booting Trusted Firmware
NOTICE: BL1: v1.5(release):ROGUE2-01.00.00.01-cpu1_2G-0-g06b570a8d (Marvell-release-1.3.0)
NOTICE: BL1: Built : 14:34:11, Feb 7 2020
NOTICE: BL1: Booting BL2
console comconsole failed to initialize0.00.01-cpu1_2G-0-g06b570a8d (Marvell-release-1.3.0)
Consoles: EFI console 4:34:13, Feb 7 2020
Reading loader env vars from /efi/freebsd/loader.env
Setting currdev to disk1p1:):ROGUE2-01.00.00.01-cpu1_2G-0-g06b570a8d (Marvell-release-1.3.0)
FreeBSD/arm64 EFI loader, Revision 1.1
(Fri Feb 10 20:26:39 UTC 2023 root@freebsd)
U-Boot 2018.03-devel-1.2.0ROGUE2-01.00.00.02+ (Feb 07 2020 - 14:33:22 -0500)
Command line arguments: loader.efi
Image base: 0x1000000
EFI version: 2.70[MHz]
EFI Firmware: Das U-Boot (rev 0.00)
Console: efi,comconsole (0)
Load Path: /\efi\boot\bootaa64.efi
Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(0,0)/HD(1,0x01,0,0x1,0x64000)
Trying ESP: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(0,0)/HD(1,0x01,0,0x1,0x64000)
Setting currdev to disk1p1:25 Gbps
Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(0,0)/HD(2,0x01,0,0x64001,0x1117c)
Setting currdev to disk1p2:bps
Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(0,0)/HD(3,0x01,0,0x7517d,0x3b2dd33)
Setting currdev to disk1p3:
ERROR: cannot open /boot/lua/loader.lua: no such file or directory. ofdata clock 200000000, frequency 20000000
SF: Detected w25q32bv with page size 256 Bytes, erase size 4 KiB, total 4 MiB
OK
Type '?' for a list of commands, 'help' for more detailed help.
OK : eth0: neta@30000 [PRIME], eth1: neta@40000
Hit any key to stop autoboot: 0
Setting bus to 1
** No partition table - mmc 0 **Reset SCSI
scanning bus for devices...
Bus 0
Device 0: (0:0) Vendor: ATA Prod.: ATP SATA III M.2 Rev: SBFM
Type: Hard Disk
Capacity: 30533.8 MB = 29.8 GB (62533296 x 512)
12725 armada-3720-netgate-1100.dtb
12725 armada-3720-sg1100.dtb
12948 armada-3720-netgate-2100.dtb
12948 armada-3720-sg2100.dtb4 file(s), 0 dir(s)
12948 bytes read in 4 ms (3.1 MiB/s)
839196 bytes read in 24 ms (33.3 MiB/s)Starting EFI application at 01000000 ...
Scanning disk sdhci@d8000.blk...
Scanning disk ahci_scsi.id0lun0...
Found 5 disks -
Update: Was able to contact negate support and they assisted me thanks.