Issue to manage pfsense from internet

rjcab

Hello,

here below my network:

The address 192.168.10.253 (WAN PFSENSE) is in DMZ

From internet when I type my https://FAI-IP:4443 no page

Still issue stupid I think ...

thanks in advance

YannTKO

@rjcab
In the WAN interface, you have to uncheck the "Block private networks and loopback addresses" and "Block bogon networks" (the 2nd one is not mandatory)

rjcab

@YannTKO many thanks

Gertjan

@rjcab

Before it becomes a huge issue : LAN resources using http, https and msrdp shouldn't be made accessible like that. It might work, but not for long, things will go pretty bad as soon as 'they' find you.

Consider setting up a VPN server on pfSense.

rjcab

@Gertjan you are right. it is just temporary

But i am still facing issue when I tried to NAT to servers behind Pfsense:

here below NAT & Rules:

in the logs:

For example it passes for 192.168.1.252:8006 but when I go to the webrowser from WAN it doesn't work but works within LAN

Again maybe my stupid error ...

Gertjan

@rjcab

This is 'strange' :

Replace the destination "192.168.1.1" with "any" or "This firewall (self).
Normally, there can't be any traffic coming into WAN with destination IP "192.168.1.1", after all 192.168.1.1 can't be routed over the internet. So it can not origin from the Internet neither.
This isn't - shouldn't be a NAT rule neither.
Traffic that comes from the Internet (and entering the WAN) has arrived at its destination. No port or addresses translating is needed == so no NAT.

Example :

Instead of hitting port 443, TCP == a web server == the pfSense default https GUI, I use this to hit port 1194, UDP, the pfSense OpenVPN server :

Your second, 'NAT pve' rule seems to work.

For your third rule you need to talk to the administrator of the 192.168.1.220.
You should know that a microsoft device that accepts RDP only accepts connection from it's own LAN, normally 192.168.1.0/24 - and no body else (Microsoft really want to the user to be save ^^).
So you have to set up the RDP access on that 192.168.1.220 device so that it accepts connections from 'everybody'.

To see if it works : Packet capturing to the rescue :

and hit start.

Now, go to your neighbor, use his connection.
Or use your phone with the Wifi switched to Off !
Do not use your local network resources ( !!!!!!!!!!!! )

Connect to your WAN IP :

where 1.2.3.4 is your WAN IP.

Always start the easy way : use an IP.
Later on, you can use a DDNS type host name that always points to your WAN IP.

An note this some where :
Do not (try to) use your WAN IP while being connected on your your LAN.
If you are on your LAN, use 192.168.1.220 as an IP, or create a host over ride for it in the resolver like
server.hoe.arpa that point to 192.168.1.220.

Rule 4 and 5 : created by 'Easyrule' ? NAT rules can't be created using Easy rule.

rjcab

@Gertjan said in Issue to manage pfsense from internet:

Your second, 'NAT pve' rule seems to work.

thanks for your time.

If I focus on 'NAT pve', I don't know how to investigate further to identify the cause.
For the RDP issue .220 I will check further on the server itself.

Gertjan

@rjcab said in Issue to manage pfsense from internet:

If I focus on 'NAT pve', I don't know how to investigate further to identify the cause.

You know where the traffic arrives : the WAN interface.
You should know what WAN IP you have : [https://www.whatismyip.com/) : click and you'll know ^^
You know what destination port is used : 8006
You know what protocol is used : TCP.

Now you know enough to check if traffic arrives at the WAN gates :

Hit start, and go drink a coffee at your neighbors place. Use their Internet access again, and visit the IP you've found as you WAN IPv4.
That all there is.

If the Packet Capture starts to capture packets, you know traffic comes into the WAN interface.
Traffic you've emitted ? Easy to check also as the source IPv4 should be the IP you used when you were at your neighbors place.

If all this went well, you've proven a very important step : does the traffic arrive at your pfsense as it is totally a waste of time if the traffic isn't even arrive at your pfSense. This can happen if you were using an upstream ISP router : you have to NAT that router also.
Your ISP could also block incoming connection ...
Or you use some sort of CGNAtted IP (given to you by your ISP) so you can't access your pfSense whatever you try.