Firewall Rule Counters Max Size?
-
I'll double check my rules I guess and make sure I'm not doing something silly.
-
OK, things are still not adding up. I updated the rule yesterday afternoon so that it would be more inclusive of traffic, to make sure I'm counting the traffic in this rule and not getting caught in another rule. I know from the backup logs that we uploaded roughly 1TiB, but my rule is showing less than 4GiB. The CLI counters in pfctl agree with the webui, so is something weird in pf?
-
Going to filter through the output of pfctl and try to figure out if this traffic is hitting another rule and getting counted elsewhere. Even if this is wrapping at 2^32 this is just not making sense.
-
Hmm, in a test here I created a new rule to pass iperf traffic on port 5201 then ran an iperf test against it:
[24.03-RELEASE][admin@4200.stevew.lan]/root: pfctl -vvsr | grep -A3 @90 @90 pass in quick on igc3 reply-to (igc3 172.21.16.1) inet proto tcp from <WAN__NETWORK:1> to 172.21.16.11 port = 5201 flags S/SA keep state (if-bound) label "USER_RULE: Allow iperf" label "id:1716563048" ridentifier 1716563048 [ Evaluations: 28 Packets: 0 Bytes: 0 States: 0 ] [ Inserted: uid 0 pid 0 State Creations: 0 ] [ Last Active Time: N/A ][ ID] Interval Transfer Bitrate [ 5] 0.00-60.00 sec 6.58 GBytes 941 Mbits/sec receiver[24.03-RELEASE][admin@4200.stevew.lan]/root: pfctl -vvsr | grep -A3 @90 @90 pass in quick on igc3 reply-to (igc3 172.21.16.1) inet proto tcp from <WAN__NETWORK:1> to 172.21.16.11 port = 5201 flags S/SA keep state (if-bound) label "USER_RULE: Allow iperf" label "id:1716563048" ridentifier 1716563048 [ Evaluations: 40 Packets: 9752720 Bytes: 7568082888 States: 2 ] [ Inserted: uid 0 pid 0 State Creations: 3 ] [ Last Active Time: Fri May 24 16:10:00 2024 ]So I'd say it's counting traffic in both directions.
However there is an issue here. Still digging....
-
OK, I just did a test upload of 2GiB and now the counter has gone from 3.79GiB before to 1.64GiB now. WTF
-
Yeah, there's definitely an issue. Just trying to define it before I open a bug.
-
@GeorgePatches said in Firewall Rule Counters Max Size?:
OK, I just did a test upload of 2GiB and now the counter has gone from 3.79GiB before to 1.64GiB now. WTF
We have some well over 4 GB (96) so that's not it. I would guess, something's resetting the counter.
Here's some more fun info, I found https://www.reddit.com/r/PFSENSE/comments/eo62f4/how_to_reset_bytes_in_states_on_firewall_rule/, from (I would guess) "our"/Netgate's Jim P which says Filter Reload should zero them. However if I run a reload it reduces some of the numbers but does not zero them out.
I wasn't paying close attention to which was 96 GB above but that's gone, however I have several over 5 GB still with zero states. I'm looking at our data center router so it should have traffic but not 5 GB in a few seconds.
-
Yup doesn't zero them here. Running
pfctl -F allto flush everything does reset them but it also removes all the rules etc until you reload them. So don't do that! -
-
if the goal is to zero all the rules, wouldn't pfctl -z be what you want?
-
Ha, yup. Not sure how I missed that, thanks!
-
If my rules are getting zeroed repeatedly, would this be logged anywhere I could check?
Another thought, could this have something to do with the fact that we're rolling our traffic logs over at a staggering rate? I think we roll all 7 50MB filter log files in 30 minutes.
-
