Netgate 7100-1U New NIC setup issues
-
The LAN interface should not have a gateway configured on it directly.
The only reason you would ever have a gateway on LAN would be if you had a downstream router connected to it. That could be a layer3 switch but you would then need to have static routes setup to other downstream subnets. You are not using anything like that as I understand it so you should remove the gateway.
The NIC results are as expected so you have the correct NIC configured.
Physically how are these things connected?
There must be some layer 2 connection to the ISP router if clients are pulling a lease from there. So a misconfigured vlan on the switch perhaps?
-
@stephenw10 i did factory reset and will be configuring negate through isp wan external ip .
I have fiber sfp xgpon hooked to isp router/modem and from there hooked to netgate wan ixo and ix3 hooked sfp+ to external switch -
@Sammy2Netgo do i need to setup vlans during first initial interface config ?
-
@Sammy2Netgo do i need opt 1 & opt 2 set in interface assignments ?
I started with
Wan ix0
Lan ix3
I left out opt 1 opt2 -
This post is deleted! -
@stephenw10 but my dhcp on lan will need to have gateway set on dhcp lan to be able to connect to router gui from switch ??
This is how i set lan ix3 settings :
Enter lan ipv4 -192.168.xxx.xxx
Subnet mask -24
For wan enter lan ipv4 upstream gateway adress :
Enter for none
Enable dchp server on lan -yes
Start ip range -192.168.1.0
End ip range -192.168.1.255 -
No you shouldn't need to setup any VLANs to get initial connectivity. You are not using the on-board switch. JUst WAN and LAN configured like that should be fine.
-
@Sammy2Netgo said in Netgate 7100-1U New NIC setup issues:
but my dhcp on lan will need to have gateway set on dhcp lan to be able to connect to router gui from switch ??
Yes, but that's not what a gateway on the interface itself is for. That defines what pfSense itself uses as a gateway. The DHCP server will pass the interface address to clients to use as a gateway.
-
@stephenw10 this new card is causing nothing but problems in the configs
So what do i need to do to get connectivity ? When i factory reset even the port 1 which should be wan lagg0.4090 wont work to obtain ip
Can you let me know setup procedure from beginning factory reset and console port assignments or anything that needs to be done to regain connectivity/Thanx
Factory resetting the netgate with new card how would i gain access to web gui ?Which port as wan and lan by default with new card installed
Factory reset default assignments -
Wan>lagg0.4090
Lan>lagg0.4091
Opt1>ix0
Opt2>ix1 -
OK so you need this extra NIC to get 10Gbase-T connections? Some Nbase rate?
Let me create a default config you can use....
-
PM'd you a test config.
-
@stephenw10 yes i need and use the new rj45 card for 10G connection for wan as my fiber upgrade from gpon to 10G xgspon module not recognized in sfp+ interface
This new card does 1 g 2.5G 5G and 10G multi rate
Its an x550-T2 card -
@stephenw10
Is there easier way of loading the config xml ? i read that using shell script can load from usb without restarting just to go to boot Is this correct ?I copied the xml you sent me into usb and plug the usb but it didn't load the config during reboot which should be automatically ? I copied the cml to usb but it wont detect it -
PM'd you but you probably need to rename the file
config.xml -
@stephenw10 so after renaming i insert usb and reboot and it should detect and install the config or i have to do anything else ?
-
@Sammy2Netgo
Usb formatted fat32 and file renamed to config.XML
Now instead loading config file its trying to boot from it and says not a bootable device what do i do ? -
@stephenw10 here is what i did to gain access to web gui of netgate from console
Wan lagg0.4090 had to take off ix0
Lan ix1 with ip and dhcp set
I then hooked pc into ix1 with gateway ip
Boom im in web GUI now im trying to figure out once in gui i set wan back to ixo and it worked
Whats next as i cant see ix3 in assignments -
Ah, yes in the default configuration ix2 and ix3 are part of the lagg so not available for assigning.
You still have the additional NIC present?
You can try restoring the config I sent you to use that.
-
@stephenw10 ya ix and ix2 not visible in web gui-
How do i restore the config.XML ? I tried but nothing uploaded -i read somewhere that if those assignments are missing pfsense has to be reinstalled ?How do i get this thing to recognize and upload the config ? -
@stephenw10 was wondering if i just said screw it and pull the new card out and do factory reset will those ports assign back to the way they were before ? Then set the assignments accordingly and then put the new card back in ? I dont understand but even if i got access through wan there is no point as ix2 and ix3 dont exist in web GUI or thats only cause i put
Ix1 as lagg0.4091 which is the secondary port on the new card -I dont think it allows for wan/lan on same card both of the ports have to be of the same wan or lan not wan/lan ? Im looking the easiest and less time constraining option as this issue has wasted so many days of my time
What is ix4 and ix5 in assignments isnt that part of lagg0 switch 2.5G do i need those ?
