Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    Netgate Device ID changing on power loss

    Scheduled Pinned Locked Moved Hardware
    25 Posts 5 Posters 1.8k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • N
      n1ck31 @stephenw10
      last edited by

      @stephenw10 Thanks for that, unfortunately the NDI still changed again after a hard reset. (I double checked, its gone in the ifconfig command now)

      Although that interface was probably part of the problem, it wasn't the only problem.

      Do you have any other ideas? For now I've downgraded back to CE until I can get this solved.

      N 1 Reply Last reply Reply Quote 0
      • N
        n1ck31 @n1ck31
        last edited by

        @n1ck31 said in Netgate Device ID changing on power loss:

        @stephenw10 Thanks for that, unfortunately the NDI still changed again after a hard reset. (I double checked, its gone in the ifconfig command now)

        Although that interface was probably part of the problem, it wasn't the only problem.

        Do you have any other ideas? For now I've downgraded back to CE until I can get this solved.

        Never mind, after another reboot, it's back. (ue0)

        I've checked BIOS, nowhere to disable this that I can see.

        1 Reply Last reply Reply Quote 0
        • provelsP
          provels
          last edited by

          Are you bridging interfaces? If not, never mind.

          Peder

          MAIN - pfSense+ 24.11-RELEASE - Adlink MXE-5401, i7, 16 GB RAM, 64 GB SSD. 500 GB HDD for SyslogNG
          BACKUP - pfSense+ 23.01-RELEASE - Hyper-V Virtual Machine, Gen 1, 2 v-CPUs, 3 GB RAM, 8GB VHDX (Dynamic)

          N 1 Reply Last reply Reply Quote 0
          • stephenw10S
            stephenw10 Netgate Administrator
            last edited by stephenw10

            Hmm, it didn't disable it?

            Do you see the line as expected in /boot/loader.conf.local?

            Try running: usbconfig dump_device_desc

            That might show you what that device actually is.

            1 Reply Last reply Reply Quote 0
            • N
              n1ck31 @provels
              last edited by n1ck31

              @provels Not intentionally, asrock has no options for it other than this network bond config which isn't the same thing.
              57143e11-76b1-46eb-9747-c1f8f3feffdf-image.png

              @stephenw10 Yep, I can see it there in the file, and nope it didn't disable it.

              This is the output of that command:

              I don't see it there... (yet its still in the system)

              /root: usbconfig dump_device_desc
ugen1.1: <AMD XHCI root HUB> at usbus1, cfg=0 md=HOST spd=SUPER (5.0Gbps) pwr=SA                                                                                                  VE (0mA)

  bLength = 0x0012
  bDescriptorType = 0x0001
  bcdUSB = 0x0300
  bDeviceClass = 0x0009  <HUB>
  bDeviceSubClass = 0x0000
  bDeviceProtocol = 0x0003
  bMaxPacketSize0 = 0x0009
  idVendor = 0x0000
  idProduct = 0x0000
  bcdDevice = 0x0100
  iManufacturer = 0x0001  <AMD>
  iProduct = 0x0002  <XHCI root HUB>
  iSerialNumber = 0x0000  <no string>
  bNumConfigurations = 0x0001

ugen0.1: <AMD XHCI root HUB> at usbus0, cfg=0 md=HOST spd=SUPER (5.0Gbps) pwr=SA                                                                                                  VE (0mA)

  bLength = 0x0012
  bDescriptorType = 0x0001
  bcdUSB = 0x0300
  bDeviceClass = 0x0009  <HUB>
  bDeviceSubClass = 0x0000
  bDeviceProtocol = 0x0003
  bMaxPacketSize0 = 0x0009
  idVendor = 0x0000
  idProduct = 0x0000
  bcdDevice = 0x0100
  iManufacturer = 0x0001  <AMD>
  iProduct = 0x0002  <XHCI root HUB>
  iSerialNumber = 0x0000  <no string>
  bNumConfigurations = 0x0001

ugen2.1: <AMD XHCI root HUB> at usbus2, cfg=0 md=HOST spd=SUPER (5.0Gbps) pwr=SA                                                                                                  VE (0mA)

  bLength = 0x0012
  bDescriptorType = 0x0001
  bcdUSB = 0x0300
  bDeviceClass = 0x0009  <HUB>
  bDeviceSubClass = 0x0000
  bDeviceProtocol = 0x0003
  bMaxPacketSize0 = 0x0009
  idVendor = 0x0000
  idProduct = 0x0000
  bcdDevice = 0x0100
  iManufacturer = 0x0001  <AMD>
  iProduct = 0x0002  <XHCI root HUB>
  iSerialNumber = 0x0000  <no string>
  bNumConfigurations = 0x0001

ugen0.2: <American Megatrends Inc. Virtual Hub> at usbus0, cfg=0 md=HOST spd=HIG                                                                                                  H (480Mbps) pwr=SAVE (100mA)

  bLength = 0x0012
  bDescriptorType = 0x0001
  bcdUSB = 0x0200
  bDeviceClass = 0x0009  <HUB>
  bDeviceSubClass = 0x0000
  bDeviceProtocol = 0x0001
  bMaxPacketSize0 = 0x0040
  idVendor = 0x046b
  idProduct = 0xff01
  bcdDevice = 0x0100
  iManufacturer = 0x0001  <American Megatrends Inc.>
  iProduct = 0x0002  <Virtual Hub>
  iSerialNumber = 0x0003  <serial>
  bNumConfigurations = 0x0001

ugen0.3: <American Megatrends Inc. Virtual Ethernet> at usbus0, cfg=0 md=HOST sp                                                                                                  d=HIGH (480Mbps) pwr=ON (0mA)

  bLength = 0x0012
  bDescriptorType = 0x0001
  bcdUSB = 0x0200
  bDeviceClass = 0x0002  <Communication device>
  bDeviceSubClass = 0x0000
  bDeviceProtocol = 0x0000
  bMaxPacketSize0 = 0x0040
  idVendor = 0x046b
  idProduct = 0xffb0
  bcdDevice = 0x0100
  iManufacturer = 0x0001  <American Megatrends Inc.>
  iProduct = 0x0002  <Virtual Ethernet>
  iSerialNumber = 0x0003  <1234567890>
  bNumConfigurations = 0x0002

ugen0.4: <American Megatrends Inc. Virtual Keyboard and Mouse> at usbus0, cfg=0                                                                                                   md=HOST spd=LOW (1.5Mbps) pwr=ON (0mA)

  bLength = 0x0012
  bDescriptorType = 0x0001
  bcdUSB = 0x0110
  bDeviceClass = 0x0000  <Probed by interface class>
  bDeviceSubClass = 0x0000
  bDeviceProtocol = 0x0000
  bMaxPacketSize0 = 0x0008
  idVendor = 0x046b
  idProduct = 0xff10
  bcdDevice = 0x0100
  iManufacturer = 0x0001  <American Megatrends Inc.>
  iProduct = 0x0002  <Virtual Keyboard and Mouse>
  iSerialNumber = 0x0000  <no string>
  bNumConfigurations = 0x0001

ugen0.5: <American Megatrends Inc. Virtual Cdrom Device> at usbus0, cfg=0 md=HOS                                                                                                  T spd=HIGH (480Mbps) pwr=ON (0mA)

  bLength = 0x0012
  bDescriptorType = 0x0001
  bcdUSB = 0x0200
  bDeviceClass = 0x0000  <Probed by interface class>
  bDeviceSubClass = 0x0000
  bDeviceProtocol = 0x0000
  bMaxPacketSize0 = 0x0040
  idVendor = 0x046b
  idProduct = 0xff20
  bcdDevice = 0x0100
  iManufacturer = 0x0001  <American Megatrends Inc.>
  iProduct = 0x0002  <Virtual Cdrom Device>
  iSerialNumber = 0x0003  <AAAABBBBCCCC1>
  bNumConfigurations = 0x0001

ugen0.6: <American Megatrends Inc. Virtual HardDisk Device> at usbus0, cfg=0 md=                                                                                                  HOST spd=HIGH (480Mbps) pwr=ON (0mA)

  bLength = 0x0012
  bDescriptorType = 0x0001
  bcdUSB = 0x0200
  bDeviceClass = 0x0000  <Probed by interface class>
  bDeviceSubClass = 0x0000
  bDeviceProtocol = 0x0000
  bMaxPacketSize0 = 0x0040
  idVendor = 0x046b
  idProduct = 0xff31
  bcdDevice = 0x0100
  iManufacturer = 0x0001  <American Megatrends Inc.>
  iProduct = 0x0002  <Virtual HardDisk Device>
  iSerialNumber = 0x0003  <AAAABBBBCCCC3>
  bNumConfigurations = 0x0001

              EDIT: Nevermind, here it is:

              ugen0.3: <American Megatrends Inc. Virtual Ethernet> at usbus0, cfg=0 md=HOST sp                                                                                                  d=HIGH (480Mbps) pwr=ON (0mA)
              1 Reply Last reply Reply Quote 0
              • stephenw10S
                stephenw10 Netgate Administrator
                last edited by

                Yup so it's a virtual device. If there's nothing in the BIOS then maybe something in the IPMI setup?

                How does it appear in the boot log when it attaches? You might need to try disabling cdce0 instead. If that's how it appears.

                N 1 Reply Last reply Reply Quote 0
                • N
                  n1ck31 @stephenw10
                  last edited by n1ck31

                  @stephenw10 Nothing in both places. Only things I can disable are the virtual media devices & KBM emulation. No mention of any virtual network adapters at all.

                  This is all thats mentioned of it in the boot log:

                  uhub2: 6 ports with 6 removable, self powered
uhub1: 6 ports with 6 removable, self powered
uhub0: 22 ports with 22 removable, self powered
Root mount waiting for: usbus0
ugen0.2: <American Megatrends Inc. Virtual Hub> at usbus0
uhub3 on uhub0
uhub3: <7-port Hub> on usbus0
uhub3: 5 ports with 5 removable, self powered
Root mount waiting for: usbus0
ugen0.3: <American Megatrends Inc. Virtual Ethernet> at usbus0
Root mount waiting for: usbus0
ugen0.4: <American Megatrends Inc. Virtual Keyboard and Mouse> at usbus0
ukbd0 on uhub3
ukbd0: <Keyboard Interface> on usbus0
kbd2 at ukbd0
                  Bob.DigB 1 Reply Last reply Reply Quote 0
                  • Bob.DigB
                    Bob.Dig LAYER 8 @n1ck31
                    last edited by Bob.Dig

                    @n1ck31 Maybe try disabling the BMC with a jumper and see if this helps.


                    Screenshot 2024-11-01 102940.png

                    N 1 Reply Last reply Reply Quote 0
                    • stephenw10S
                      stephenw10 Netgate Administrator
                      last edited by

                      It must list the device and the driver attaching to it in the boot log. Something like:

                      ugen0.3: <Realtek USB 10/100/1G/2.5G LAN> at usbus0
cdce0 on uhub0
cdce0: <CDC Communications Control> on usbus0
ue0: <USB Ethernet> on cdce0
ue0: Ethernet address: 00:e0:81:21:78:ea

                      And if it does appear like that try adding to loader.conf.local: hint.cdce.0.disabled="1"

                      N 1 Reply Last reply Reply Quote 0
                      • N
                        n1ck31 @Bob.Dig
                        last edited by

                        @Bob-Dig said in Netgate Device ID changing on power loss:

                        @n1ck31 Maybe try disabling the BMC with a jumper and see if this helps.


                        Screenshot 2024-11-01 102940.png

                        Although that probably will solve the issue, that negates the scalped price I paid for this board originally - if i were to go this route I'd just buy a regular consumer board and swap it out.

                        1 Reply Last reply Reply Quote 0
                        • N
                          n1ck31 @stephenw10
                          last edited by

                          @stephenw10 said in Netgate Device ID changing on power loss:

                          It must list the device and the driver attaching to it in the boot log. Something like:

                          ugen0.3: <Realtek USB 10/100/1G/2.5G LAN> at usbus0
cdce0 on uhub0
cdce0: <CDC Communications Control> on usbus0
ue0: <USB Ethernet> on cdce0
ue0: Ethernet address: 00:e0:81:21:78:ea

                          And if it does appear like that try adding to loader.conf.local: hint.cdce.0.disabled="1"

                          Here's the full log file

                          It seems that it's usbus0 on xhci0, so maybe disabling xhci0?

                          Copyright (c) 1992-2023 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 14.0-CURRENT amd64 1400094 #1 RELENG_2_7_2-n255948-8d2b56da39c: Wed Dec 6 20:45:47 UTC 2023
root@freebsd:/var/jenkins/workspace/pfSense-CE-snapshots-2_7_2-main/obj/amd64/StdASW5b/var/jenkins/workspace/pfSense-CE-snapshots-2_7_2-main/sources/FreeBSD-src-RELENG_2_7_2/amd64.amd64/sys/pfSense amd64
FreeBSD clang version 16.0.6 (https://github.com/llvm/llvm-project.git llvmorg-16.0.6-0-g7cbf1a259152)
VT(efifb): resolution 1024x768
CPU: AMD Ryzen 5 5600G with Radeon Graphics (3900.23-MHz K8-class CPU)
Origin="AuthenticAMD" Id=0xa50f00 Family=0x19 Model=0x50 Stepping=0
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
Features2=0x7ef8320b<SSE3,PCLMULQDQ,MON,SSSE3,FMA,CX16,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,AESNI,XSAVE,OSXSAVE,AVX,F16C,RDRAND>
AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM>
AMD Features2=0x75c237ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,SKINIT,WDT,TCE,Topology,PCXC,PNXC,DBE,PL2I,MWAITX,ADMSKX>
Structured Extended Features=0x219c97a9<FSGSBASE,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,PQM,PQE,RDSEED,ADX,SMAP,CLFLUSHOPT,CLWB,SHA>
Structured Extended Features2=0x40069c<UMIP,PKU,OSPKE,VAES,VPCLMULQDQ,RDPID>
Structured Extended Features3=0x10<FSRM>
XSAVE Features=0xf<XSAVEOPT,XSAVEC,XINUSE,XSAVES>
AMD Extended Feature Extensions ID EBX=0x191ef657<CLZERO,IRPerf,XSaveErPtr,RDPRU,WBNOINVD,IBPB,IBRS,STIBP,STIBP_ALWAYSON,PREFER_IBRS,SSBD>
SVM: NP,NRIP,VClean,AFlush,DAssist,NAsids=32768
TSC: P-state invariant, performance statistics
real memory = 17179869184 (16384 MB)
avail memory = 15924834304 (15187 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <ALASKA A M I >
FreeBSD/SMP: Multiprocessor System Detected: 12 CPUs
FreeBSD/SMP: 1 package(s) x 6 core(s) x 2 hardware threads
random: registering fast source Intel Secure Key RNG
random: fast provider: "Intel Secure Key RNG"
random: unblocking device.
ioapic0 <Version 2.1> irqs 0-23
ioapic1 <Version 2.1> irqs 24-55
Launching APs: 1 3 2 10 7 11 6 8 9 4 5
TCP_ratelimit: Is now initialized
wlan: mac acl policy registered
random: entropy device external interface
kbd1 at kbdmux0
WARNING: Device "spkr" is Giant locked and may be deleted before FreeBSD 14.0.
netgate0: <unknown hardware>
efirtc0: <EFI Realtime Clock>
efirtc0: registered as a time-of-day clock, resolution 1.000000s
smbios0: <System Management BIOS> at iomem 0xbcd72000-0xbcd7201e
smbios0: Version: 3.3, BCD Revision: 3.3
acpi0: <ALASKA A M I >
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> port 0x70-0x71 on acpi0
atrtc0: registered as a time-of-day clock, resolution 1.000000s
Event timer "RTC" frequency 32768 Hz quality 0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff irq 0,8 on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 350
Event timer "HPET1" frequency 14318180 Hz quality 350
Event timer "HPET2" frequency 14318180 Hz quality 350
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <base peripheral, IOMMU> at device 0.2 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> at device 2.1 on pci0
pci1: <ACPI PCI bus> on pcib1
xhci0: <XHCI (generic) USB 3.0 controller> mem 0xfc6a0000-0xfc6a7fff irq 36 at device 0.0 on pci1
xhci0: 32 bytes context size, 64-bit DMA
usbus0 on xhci0
usbus0: 5.0Gbps Super Speed USB v3.0
ahci0: <AHCI SATA controller> mem 0xfc680000-0xfc69ffff irq 37 at device 0.1 on pci1
ahci0: AHCI v1.31 with 8 6Gbps ports, Port Multiplier supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
ahcich2: <AHCI channel> at channel 2 on ahci0
ahcich3: <AHCI channel> at channel 3 on ahci0
ahcich4: <AHCI channel> at channel 4 on ahci0
ahcich5: <AHCI channel> at channel 5 on ahci0
ahcich6: <AHCI channel> at channel 6 on ahci0
ahcich7: <AHCI channel> at channel 7 on ahci0
pcib2: <ACPI PCI-PCI bridge> irq 38 at device 0.2 on pci1
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> irq 36 at device 0.0 on pci2
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 36 at device 0.0 on pci3
pci4: <ACPI PCI bus> on pcib4
vgapci0: <VGA-compatible display> port 0xf000-0xf07f mem 0xfb000000-0xfbffffff,0xfc000000-0xfc01ffff irq 36 at device 0.0 on pci4
vgapci0: Boot video device
pcib5: <ACPI PCI-PCI bridge> irq 37 at device 1.0 on pci2
pci5: <ACPI PCI bus> on pcib5
pcib6: <ACPI PCI-PCI bridge> irq 38 at device 2.0 on pci2
pci6: <ACPI PCI bus> on pcib6
pcib7: <ACPI PCI-PCI bridge> irq 39 at device 3.0 on pci2
pci7: <ACPI PCI bus> on pcib7
igc0: <Intel(R) Ethernet Controller I225-V> mem 0xfc300000-0xfc3fffff,0xfc400000-0xfc403fff irq 39 at device 0.0 on pci7
igc0: Using 1024 TX descriptors and 1024 RX descriptors
igc0: Using 4 RX queues 4 TX queues
igc0: Using MSI-X interrupts with 5 vectors
igc0: Ethernet address: 88:c9:b3:bf:75:60
igc0: netmap queues/slots: TX 4/1024, RX 4/1024
pcib8: <ACPI PCI-PCI bridge> irq 36 at device 4.0 on pci2
pci8: <ACPI PCI bus> on pcib8
nvme0: <Generic NVMe Device> mem 0xfc500000-0xfc503fff,0xfc504000-0xfc5040ff irq 36 at device 0.0 on pci8
pcib9: <ACPI PCI-PCI bridge> irq 36 at device 8.0 on pci2
pci9: <ACPI PCI bus> on pcib9
pcib10: <ACPI PCI-PCI bridge> at device 2.2 on pci0
pci10: <ACPI PCI bus> on pcib10
ix0: <Intel(R) X550-T2> mem 0xe0800000-0xe0bfffff,0xe0c04000-0xe0c07fff irq 40 at device 0.0 on pci10
ix0: Using 2048 TX descriptors and 2048 RX descriptors
ix0: Using 6 RX queues 6 TX queues
ix0: Using MSI-X interrupts with 7 vectors
ix0: allocated for 6 queues
ix0: allocated for 6 rx queues
ix0: Ethernet address: d0:50:99:de:c1:1b
ix0: PCI Express Bus: Speed 8.0GT/s Width x1
ix0: Option ROM V1-b1927-p0 eTrack 0x80000aee PHY FW V523
ix0: netmap queues/slots: TX 6/2048, RX 6/2048
ix1: <Intel(R) X550-T2> mem 0xe0400000-0xe07fffff,0xe0c00000-0xe0c03fff irq 41 at device 0.1 on pci10
ix1: Using 2048 TX descriptors and 2048 RX descriptors
ix1: Using 6 RX queues 6 TX queues
ix1: Using MSI-X interrupts with 7 vectors
ix1: allocated for 6 queues
ix1: allocated for 6 rx queues
ix1: Ethernet address: d0:50:99:de:c1:1c
ix1: PCI Express Bus: Speed 8.0GT/s Width x1
ix1: Option ROM V1-b1927-p0 eTrack 0x80000aee PHY FW V523
ix1: netmap queues/slots: TX 6/2048, RX 6/2048
pcib11: <ACPI PCI-PCI bridge> at device 8.1 on pci0
pci11: <ACPI PCI bus> on pcib11
vgapci1: <VGA-compatible display> port 0xe000-0xe0ff mem 0xd0000000-0xdfffffff,0xe0000000-0xe01fffff,0xfcb00000-0xfcb7ffff irq 38 at device 0.0 on pci11
hdac0: <ATI (0x1637) HDA Controller> mem 0xfcb88000-0xfcb8bfff irq 39 at device 0.1 on pci11
pci11: <encrypt/decrypt> at device 0.2 (no driver attached)
xhci1: <XHCI (generic) USB 3.0 controller> mem 0xfc900000-0xfc9fffff irq 37 at device 0.3 on pci11
xhci1: 64 bytes context size, 64-bit DMA
usbus1 on xhci1
usbus1: 5.0Gbps Super Speed USB v3.0
xhci2: <XHCI (generic) USB 3.0 controller> mem 0xfc800000-0xfc8fffff irq 38 at device 0.4 on pci11
xhci2: 64 bytes context size, 64-bit DMA
usbus2 on xhci2
usbus2: 5.0Gbps Super Speed USB v3.0
hdac1: <AMD Raven HDA Controller> mem 0xfcb80000-0xfcb87fff irq 36 at device 0.6 on pci11
pcib12: <ACPI PCI-PCI bridge> at device 8.2 on pci0
pci12: <ACPI PCI bus> on pcib12
ahci1: <AMD KERNCZ AHCI SATA controller> mem 0xfcc01000-0xfcc017ff irq 34 at device 0.0 on pci12
ahci1: AHCI v1.31 with 1 6Gbps ports, Port Multiplier supported with FBS
ahcich8: <AHCI channel> at channel 0 on ahci1
ahci2: <AMD KERNCZ AHCI SATA controller> mem 0xfcc00000-0xfcc007ff irq 35 at device 0.1 on pci12
ahci2: AHCI v1.31 with 1 6Gbps ports, Port Multiplier supported with FBS
ahcich9: <AHCI channel> at channel 0 on ahci2
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
acpi_button0: <Power Button> on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
orm0: <ISA Option ROM> at iomem 0xc0000-0xc7fff pnpid ORM0000 on isa0
hwpstate0: <Cool`n'Quiet 2.0> on cpu0
Timecounter "TSC-low" frequency 1949999786 Hz quality 1000
Timecounters tick every 1.000 msec
ZFS filesystem version: 5
ZFS storage pool version: features support (5000)
ugen1.1: <AMD XHCI root HUB> at usbus1
ugen2.1: <AMD XHCI root HUB> at usbus2
ugen0.1: <AMD XHCI root HUB> at usbus0
nvme0: Allocated 200MB host memory buffer
uhub0 on usbus1
uhub0: <AMD XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus1
uhub1 on usbus2
uhub1: <AMD XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus2
uhub2 on usbus0
uhub2: <AMD XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
hdacc0: <ATI R6xx HDA CODEC> at cad 0 on hdac0
hdaa0: <ATI R6xx Audio Function Group> at nid 1 on hdacc0
pcm0: <ATI R6xx (HDMI)> at nid 3 on hdaa0
pcm1: <ATI R6xx (HDMI)> at nid 5 on hdaa0
pcm2: <ATI R6xx (HDMI)> at nid 7 on hdaa0
pcm3: <ATI R6xx (HDMI)> at nid 9 on hdaa0
Trying to mount root from zfs:pfSense/ROOT/default []...
nda0 at nvme0 bus 0 scbus10 target 0 lun 1
nda0: <WD Blue SN570 250GB 234110WD 22395T804226>
nda0: Serial Number 22395T804226
nda0: nvme version 1.4
nda0: 238475MB (488397168 512 byte sectors)
uhub1: 6 ports with 6 removable, self powered
uhub0: 6 ports with 6 removable, self powered
uhub2: 22 ports with 22 removable, self powered
Root mount waiting for: usbus0
ugen0.2: <American Megatrends Inc. Virtual Hub> at usbus0
uhub3 on uhub2
uhub3: <7-port Hub> on usbus0
uhub3: 5 ports with 5 removable, self powered
Root mount waiting for: usbus0
ugen0.3: <American Megatrends Inc. Virtual Ethernet> at usbus0
Root mount waiting for: usbus0
ugen0.4: <American Megatrends Inc. Virtual Keyboard and Mouse> at usbus0
ukbd0 on uhub3
ukbd0: <Keyboard Interface> on usbus0
kbd2 at ukbd0
CPU: AMD Ryzen 5 5600G with Radeon Graphics (3900.00-MHz K8-class CPU)
Origin="AuthenticAMD" Id=0xa50f00 Family=0x19 Model=0x50 Stepping=0
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
Features2=0x7ef8320b<SSE3,PCLMULQDQ,MON,SSSE3,FMA,CX16,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,AESNI,XSAVE,OSXSAVE,AVX,F16C,RDRAND>
AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM>
AMD Features2=0x75c237ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,SKINIT,WDT,TCE,Topology,PCXC,PNXC,DBE,PL2I,MWAITX,ADMSKX>
Structured Extended Features=0x219c97a9<FSGSBASE,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,PQM,PQE,RDSEED,ADX,SMAP,CLFLUSHOPT,CLWB,SHA>
Structured Extended Features2=0x40069c<UMIP,PKU,OSPKE,VAES,VPCLMULQDQ,RDPID>
Structured Extended Features3=0x10<FSRM>
XSAVE Features=0xf<XSAVEOPT,XSAVEC,XINUSE,XSAVES>
AMD Extended Feature Extensions ID EBX=0x191ef657<CLZERO,IRPerf,XSaveErPtr,RDPRU,WBNOINVD,IBPB,IBRS,STIBP,STIBP_ALWAYSON,PREFER_IBRS,SSBD>
SVM: NP,NRIP,VClean,AFlush,DAssist,NAsids=32768
TSC: P-state invariant, performance statistics
                          stephenw10S 1 Reply Last reply Reply Quote 0
                          • stephenw10S
                            stephenw10 Netgate Administrator @n1ck31
                            last edited by

                            You should disable the on-board audio, though I doubt it's connected to this issue:

                            hdacc0: <ATI R6xx HDA CODEC> at cad 0 on hdac0
hdaa0: <ATI R6xx Audio Function Group> at nid 1 on hdacc0
pcm0: <ATI R6xx (HDMI)> at nid 3 on hdaa0
pcm1: <ATI R6xx (HDMI)> at nid 5 on hdaa0
pcm2: <ATI R6xx (HDMI)> at nid 7 on hdaa0
pcm3: <ATI R6xx (HDMI)> at nid 9 on hdaa0

                            Ok the actual driver attachment looks to have happened after the bootlog completes but it should be in the main system log.

                            Yes, you could disable the usbus or root device completely but it would be better to disable just the Ethernet device if you can.

                            N 1 Reply Last reply Reply Quote 0
                            • stephenw10S
                              stephenw10 Netgate Administrator
                              last edited by

                              Try running: usbconfig -d ugen0.3 dump_all_config_desc

                              It looks like it has more than one config index, in which case we can force the other one which may make it fail to load.

                              1 Reply Last reply Reply Quote 0
                              • N
                                n1ck31 @stephenw10
                                last edited by

                                @stephenw10 said in Netgate Device ID changing on power loss:

                                You should disable the on-board audio, though I doubt it's connected to this issue:

                                hdacc0: <ATI R6xx HDA CODEC> at cad 0 on hdac0
hdaa0: <ATI R6xx Audio Function Group> at nid 1 on hdacc0
pcm0: <ATI R6xx (HDMI)> at nid 3 on hdaa0
pcm1: <ATI R6xx (HDMI)> at nid 5 on hdaa0
pcm2: <ATI R6xx (HDMI)> at nid 7 on hdaa0
pcm3: <ATI R6xx (HDMI)> at nid 9 on hdaa0

                                Ok the actual driver attachment looks to have happened after the bootlog completes but it should be in the main system log.

                                Yes, you could disable the usbus or root device completely but it would be better to disable just the Ethernet device if you can.

                                I'll look into disabling the audio, agreed, makes no sense having that on.

                                Here's the output of the command in your second comment:

                                /root: usbconfig -d ugen0.3 dump_all_con                                                                                                                                                fig_desc
ugen0.3: <American Megatrends Inc. Virtual Ethernet> at usbus0, cfg=0 md=HOST sp                                                                                                                                                d=HIGH (480Mbps) pwr=ON (0mA)


 Configuration index 0

    bLength = 0x0009
    bDescriptorType = 0x0002
    wTotalLength = 0x0050
    bNumInterfaces = 0x0002
    bConfigurationValue = 0x0001
    iConfiguration = 0x0000  <no string>
    bmAttributes = 0x00c0
    bMaxPower = 0x0000

    Interface 0
      bLength = 0x0009
      bDescriptorType = 0x0004
      bInterfaceNumber = 0x0000
      bAlternateSetting = 0x0000
      bNumEndpoints = 0x0001
      bInterfaceClass = 0x0002  <Communication device>
      bInterfaceSubClass = 0x0002
      bInterfaceProtocol = 0x00ff
      iInterface = 0x0004  <RNDIS Notification Interface>

      Additional Descriptor

      bLength = 0x05
      bDescriptorType = 0x24
      bDescriptorSubType = 0x00
       RAW dump:
       0x00 | 0x05, 0x24, 0x00, 0x10, 0x01


      Additional Descriptor

      bLength = 0x05
      bDescriptorType = 0x24
      bDescriptorSubType = 0x01
       RAW dump:
       0x00 | 0x05, 0x24, 0x01, 0x00, 0x01


      Additional Descriptor

      bLength = 0x04
      bDescriptorType = 0x24
      bDescriptorSubType = 0x02
       RAW dump:
       0x00 | 0x04, 0x24, 0x02, 0x00


      Additional Descriptor

      bLength = 0x05
      bDescriptorType = 0x24
      bDescriptorSubType = 0x06
       RAW dump:
       0x00 | 0x05, 0x24, 0x06, 0x00, 0x01


      Additional Descriptor

      bLength = 0x0d
      bDescriptorType = 0x24
      bDescriptorSubType = 0x0f
       RAW dump:
       0x00 | 0x0d, 0x24, 0x0f, 0x05, 0x00, 0x00, 0x00, 0x00,
       0x08 | 0xea, 0x05, 0x00, 0x00, 0x00


     Endpoint 0
        bLength = 0x0007
        bDescriptorType = 0x0005
        bEndpointAddress = 0x0081  <IN>
        bmAttributes = 0x0003  <INTERRUPT>
        wMaxPacketSize = 0x0400
        bInterval = 0x0001
        bRefresh = 0x0000
        bSynchAddress = 0x0000


    Interface 1
      bLength = 0x0009
      bDescriptorType = 0x0004
      bInterfaceNumber = 0x0001
      bAlternateSetting = 0x0000
      bNumEndpoints = 0x0002
      bInterfaceClass = 0x000a  <CDC-data>
      bInterfaceSubClass = 0x0000
      bInterfaceProtocol = 0x0000
      iInterface = 0x0006  <RNDIS Data Interface>

     Endpoint 0
        bLength = 0x0007
        bDescriptorType = 0x0005
        bEndpointAddress = 0x0002  <OUT>
        bmAttributes = 0x0002  <BULK>
        wMaxPacketSize = 0x0200
        bInterval = 0x0000
        bRefresh = 0x0000
        bSynchAddress = 0x0000

     Endpoint 1
        bLength = 0x0007
        bDescriptorType = 0x0005
        bEndpointAddress = 0x0083  <IN>
        bmAttributes = 0x0002  <BULK>
        wMaxPacketSize = 0x0200
        bInterval = 0x0000
        bRefresh = 0x0000
        bSynchAddress = 0x0000



 Configuration index 1

    bLength = 0x0009
    bDescriptorType = 0x0002
    wTotalLength = 0x0050
    bNumInterfaces = 0x0002
    bConfigurationValue = 0x0002
    iConfiguration = 0x0000  <no string>
    bmAttributes = 0x00c0
    bMaxPower = 0x0000

    Interface 0
      bLength = 0x0009
      bDescriptorType = 0x0004
      bInterfaceNumber = 0x0000
      bAlternateSetting = 0x0000
      bNumEndpoints = 0x0001
      bInterfaceClass = 0x0002  <Communication device>
      bInterfaceSubClass = 0x0006
      bInterfaceProtocol = 0x0000
      iInterface = 0x0007  <CDC Notification Interface>

      Additional Descriptor

      bLength = 0x05
      bDescriptorType = 0x24
      bDescriptorSubType = 0x00
       RAW dump:
       0x00 | 0x05, 0x24, 0x00, 0x10, 0x01


      Additional Descriptor

      bLength = 0x05
      bDescriptorType = 0x24
      bDescriptorSubType = 0x01
       RAW dump:
       0x00 | 0x05, 0x24, 0x01, 0x00, 0x01


      Additional Descriptor

      bLength = 0x04
      bDescriptorType = 0x24
      bDescriptorSubType = 0x02
       RAW dump:
       0x00 | 0x04, 0x24, 0x02, 0x00


      Additional Descriptor

      bLength = 0x05
      bDescriptorType = 0x24
      bDescriptorSubType = 0x06
       RAW dump:
       0x00 | 0x05, 0x24, 0x06, 0x00, 0x01


      Additional Descriptor

      bLength = 0x0d
      bDescriptorType = 0x24
      bDescriptorSubType = 0x0f
       RAW dump:
       0x00 | 0x0d, 0x24, 0x0f, 0x08, 0x00, 0x00, 0x00, 0x00,
       0x08 | 0xea, 0x05, 0x00, 0x00, 0x00


     Endpoint 0
        bLength = 0x0007
        bDescriptorType = 0x0005
        bEndpointAddress = 0x0081  <IN>
        bmAttributes = 0x0003  <INTERRUPT>
        wMaxPacketSize = 0x0400
        bInterval = 0x0001
        bRefresh = 0x0000
        bSynchAddress = 0x0000


    Interface 1
      bLength = 0x0009
      bDescriptorType = 0x0004
      bInterfaceNumber = 0x0001
      bAlternateSetting = 0x0000
      bNumEndpoints = 0x0002
      bInterfaceClass = 0x000a  <CDC-data>
      bInterfaceSubClass = 0x0000
      bInterfaceProtocol = 0x0000
      iInterface = 0x0009  <CDC Data Interface>

     Endpoint 0
        bLength = 0x0007
        bDescriptorType = 0x0005
        bEndpointAddress = 0x0002  <OUT>
        bmAttributes = 0x0002  <BULK>
        wMaxPacketSize = 0x0200
        bInterval = 0x0000
        bRefresh = 0x0000
        bSynchAddress = 0x0000

     Endpoint 1
        bLength = 0x0007
        bDescriptorType = 0x0005
        bEndpointAddress = 0x0083  <IN>
        bmAttributes = 0x0002  <BULK>
        wMaxPacketSize = 0x0200
        bInterval = 0x0000
        bRefresh = 0x0000
        bSynchAddress = 0x0000
                                1 Reply Last reply Reply Quote 0
                                • stephenw10S
                                  stephenw10 Netgate Administrator
                                  last edited by

                                  Hmm, both indexs include CDC data which will likely be the ue0 device. The logs just after boot should confirm that showing cdce though.

                                  It feels like it should be possible to add a USB quirk to just stop that loading but I don't see an option for that:
                                  https://man.freebsd.org/cgi/man.cgi?query=usb_quirk

                                  Otherwise disabling cdce0 or the USB bus or controller should be possible.

                                  1 Reply Last reply Reply Quote 0
                                  • w0wW
                                    w0w
                                    last edited by

                                    I have an older ASRock Rack motherboard, and I also had my share of struggles with their BMC port sharing. On this motherboard, from what I found in my research, this virtual AMD port appears when instead of using a dedicated BMC port, you share this port for other purposes, or when you only have one cable connected to a certain port.

                                    As far as I understand and remember, the settings for this behavior are not in the BIOS but in the BMC’s web interface. In the Configuration section, there should be several options for network, link configuration, and choosing between shared or dedicated. One of these options should disable this virtual interface, but I’m not entirely sure. The motherboard manual might provide more detailed descriptions of the BMC settings, but on my board, these settings are quite confusing, and the manual doesn’t cover all of them.

                                    Overall, I had a similar idea—to have access to both the BIOS and everything else. But as usual, since their BMC relies on Java, which can’t be updated, it’s impossible to use their applets because the board is no longer supported. In the end, I connected a PiKVM to this board.

                                    For anyone considering purchasing an ASRock Rack, I highly advise against it if you plan to use the board longer than its support period (typically 2-3 years), as the BMC might "turn into a pumpkin" after that.

                                    1 Reply Last reply Reply Quote 0
                                    • First post
                                      Last post
                                    Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.